Is it easy to remove the body from an EZGO golf cart?
It is very simple to remove the body off of your EZGO golf cart if you know what to look for. This how to video will… | Golf cart bodies, Ezgo golf cart, Golf carts It is very simple to remove the body off of your EZGO golf cart if you know what to look for.
How do I remove the flywheel of an EZGO?
The flywheel of an EZGO, be it the Workhorse or Medalist can be removed by following these steps: Find out the two dome head screws in the flywheel which seems they are there for no particular reason.
How do I remove the motor from my EZGO RXV?
EZGO RXV Motor Removal Steps 1 You have to first remove the battery wires so that the cart cannot be powered. 2 Next, the air hose should be removed from the carburetor side. 3 Use a jack to lift the cart from the rear end. 4 The drive belt should then be removed. ... 5 Use the 8mm wrench to disconnect the ‘DF’ wire from the starter. More items...
How do you remove the motor from a golf cart?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
How do you remove a flywheel from a golf cart?
0:361:49HOW-TO Easily Remove A Flywheel On A Small Engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm just going to back it off a bit make sure you wear safety glasses when you do this and nowMoreAnd I'm just going to back it off a bit make sure you wear safety glasses when you do this and now with the hammer I'm just going to hit that tool and the flywheel will pop. Off.
How do you remove a flywheel without a flywheel puller?
1:304:42How to Remove a Flywheel without a Puller on a Harbor Freight Predator ...YouTubeStart of suggested clipEnd of suggested clipAnyway put the the pipe eye underneath the flywheel. Apply some pressure take a ball-peen hammer.MoreAnyway put the the pipe eye underneath the flywheel. Apply some pressure take a ball-peen hammer. And hit the end of the crankshaft. And that's how you remove a flywheel without a flywheel puller.
What would cause a gas golf cart not to fire?
First, try this: turn the key switch on, hit the accelerator, and check for a clicking noise. If you don't hear clicking, it's time to take a look at your cart's batteries. Make sure the battery is fully charged and the terminals are cleaned and secure. Next, see how the water level in the battery is holding up.
How do you check the igniter on a EZ Go golf cart?
Take the voltmeter's black and red probe and place it on the –ve and +ve terminal of the coil. Take the readings. It should be between 3.7-5.2 ohms. If outside the range, the coil should be replaced.
How do you get a magneto off without a puller?
0:081:57Remove flywheel/stator without special tools. - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake your big screwdriver thing and just sort of stick it in here stick it in here stick it in hereMoreTake your big screwdriver thing and just sort of stick it in here stick it in here stick it in here and while you're doing that. Take your hammer. Nice big hammer.
How do you use a magneto puller?
2:433:59Tusk Motorcycle Flywheel Puller - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure you've got a good grip on your tools. Also keep in mind once you've reached the rightMoreMake sure you've got a good grip on your tools. Also keep in mind once you've reached the right amount of torque to pull this off the flywheel should just pop right off.
Where is the reset button on an ezgo golf cart?
Locate the motor Remove the panel so the electric motor is visible. Electric motors usually include reset buttons that can perform similar to circuit breakers. Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
Why won't My EZGO start?
Check to make sure the golf cart transmission selector is in the "park" position. Some models of E-Z-GO gas-powered carts may fail to start with a charge if the selector is not fully in the "park" position.
Where is the solenoid on a EZGO gas golf cart?
0:065:38Replace Solenoid in Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipCart um your solenoid could be located in a bunch of different places but almost always underneathMoreCart um your solenoid could be located in a bunch of different places but almost always underneath the seat.
What does the igniter do on an ezgo golf cart?
The Nature of Golf Cart Ignitors In essence, the ignitor works to enhance electrical signals and produce a larger flow of electricity to the coil that helps your spark plug operate. In this way, it is an essential part on gas-powered golf carts but is usually not found on electrical carts as there is no need.
What causes a golf cart not to start?
As the main source of power to your electric golf cart, the batteries are commonly the cause for why your electric golf cart won't start. Acid-based batteries are typically used for electric golf carts and must be recharged in order to work properly.
Why wont my golf cart go forward or reverse?
Check the Forward/Reverse switch of your golf cart for loose connections. If the connections are intact, interchange the top and bottom wires at the rear. If the cart now goes in reverse but not forward, the problem is with the switch. You have to just change the switch in this case.
How do I remove an outboard flywheel without a puller?
1:125:57How to remove outboard motor flywheel without a puller - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what we're going to do is just bust the nut loose that's the first step typically the 18 inchMoreSo what we're going to do is just bust the nut loose that's the first step typically the 18 inch breaker bar is enough to do the job.
How do you make a flywheel puller?
0:152:42Extremely Simple Flywheel Puller - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff. So you have to be careful with the coils. And position the flywheel like this. So you don't hitMoreOff. So you have to be careful with the coils. And position the flywheel like this. So you don't hit the coil. With these bolts if you do you're.
How do you remove a flywheel from a lawn mower without a puller?
8:5610:49How To Easily Remove A Flywheel - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo use a big solid bar. It don't have to be brass it could be steel. And a lot of times you don'tMoreSo use a big solid bar. It don't have to be brass it could be steel. And a lot of times you don't even have to pry on it a lot of times you can just hold it up.
How do you remove a Briggs and Stratton flywheel?
1:374:25Briggs & Stratton Riding Lawn Mower Replace Flywheel #591759YouTubeStart of suggested clipEnd of suggested clipUnthread the bolt. And lift off the old flywheel. You're now ready to install the new flywheelMoreUnthread the bolt. And lift off the old flywheel. You're now ready to install the new flywheel aligning the notch in the flywheel with the sod and the crankshaft. Position the new flywheel.
How to change motor on Ezgo cart?
How to change the motor on a Electric EZGO: The first step is to remove the wires connecting the battery pack to ensure that the cart has no power. It is advisable to use protective gloves. Do not use wristwatch, rings or jewelry.
How to remove the engine on a 2001 Ezgo?
Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How to yank a cart motor out?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
How to remove PDS motor?
Here are the steps to remove a PDS motor: You must first put the Run-Tow/Maintenance switch to Tow/Maintenance. Disconnect the wires connecting the battery. Disconnect and remove all the wires and cables connected to the motor. You should then remove the snap ring and the speed sensor from the motor end cover.
Why is it so hard to remove a golf cart motor?
On most occasions, the difficulty in removing the motor from its place in a golf cart is due to the rust that would have developed all around. It won’t come off so easily and you can’t use too much force as it may damage some of the other parts.
Can you pull an EZGO cart up?
For starters, the input shaft could be jammed or broken, making it difficult for you to pull the motor up. You can use a hammer mildly to slowly tap and pull it off the hold and pull it up. The other issue you may face with the older models of EZGO carts is where the motor could be welded to the body.
How to remove flywheel on EZGO?
The flywheel of an EZGO, be it the Workhorse or Medalist can be removed by following these steps: Find out the two dome head screws in the flywheel which seems they are there for no particular reason. Remove the two screws and you would find two holes to connect a puller. Protect the end of the crankshaft from the puller.
How to remove a Yamaha G1 flywheel?
The G1 from Yamaha can be removed via the following steps: Use a bit of penetrating oil and wait for some time. Apply a bit of medium level of heat. Mark the timing plate once done.
How to check if a flywheel is off?
You can do so by following the below steps: Use penetrating oil and wait for some while. Then check if the flywheel gets off. Another option would be to use a bit of heat to check if the flywheel comes off. Set a mark on the timing plate . After the crank seal is removed, it can be reinstalled at the correct time.
Can a flywheel be removed without a puller?
The puller remains a very important tool without which a flywheel cannot be removed. Make sure that the flywheel gets connected to a puller by removing both screws in the surface of the flywheel. Sometimes you may face a stubborn flywheel which may make life hard for you.
