The throttle cable requires only a little slack and not too much. The following steps will help you to adjust the throttle on an EZGO RXV golf cart using a drill, a 10mm wrench and a T-45 bit. Remove the screws on both the side panels of the golf cart using the T-45 bit.
Full Answer
How do you remove the engine on a 2001 EZGO golf cart?
There is an easy way to remove the engine on a 2001 EZGO golf cart. Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How do you adjust the throttle cable on an EZGO golf cart?
How do you adjust the throttle cable on an EZGO golf cart? Close the carburetor throttle plate.. Rotate the governor arm in a counter-clockwise direction.. Keep the cable inside the throttle cable bracket that is fitted on the rear axle.. Make sure that the governor and carburetor are seated with ...
Where is the tow switch on an EZ GO golf cart?
Lift your E-Z-Go cart’s front seat. You will see the tow/run switch; turn it to tow instead of run. Look for wires labeled 1, 2, 3, 4 and ensure that wire 1 connects to wire2 and where wire3 connects to wire 4.
What does a throttle cable do on a golf cart?
It ensures that your golf cart operation is smooth and safe. A throttle cable assists in the efficient utilization of the batteries and gas of the golf cart. How do you adjust the throttle cable on an EZGO golf cart?
How do I remove a throttle cable?
0:021:11Removing Throttle Cable from Throttle Body - YouTubeYouTubeStart of suggested clipEnd of suggested clipBody what I normally do is I take a ballpoint pen like this push down on the throttle arm here getMoreBody what I normally do is I take a ballpoint pen like this push down on the throttle arm here get underneath the cable. Move it all the way to the end like this just pop the cable right off.
How do I remove the throttle cable from my accelerator pedal?
2:046:43Accelerator Cable Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust pull out on it. Just snaps right out of the pedal. And then there's a little groove in the armMoreJust pull out on it. Just snaps right out of the pedal. And then there's a little groove in the arm for the cable. And then there it is cable is all free of the pedal.
How do you adjust the throttle cable on a EZGO golf cart?
2:446:13How to Adjust Governor on EZGO RXV Gas Golf Cart | Speed IncreaseYouTubeStart of suggested clipEnd of suggested clipLess exposed in other words we want to get this housing pushed back in order to do that we'll takeMoreLess exposed in other words we want to get this housing pushed back in order to do that we'll take this outer nut loose. And run it closer to the edge. Then move the jamb nut up closer to it.
How do you remove throttle cable from handlebars?
1:406:29How to remove a throttle tube and put it back on - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe easiest way to do this is to pick the housing up and just pull the housing. Against the cable.MoreThe easiest way to do this is to pick the housing up and just pull the housing. Against the cable.
How do you install a push pull throttle cable?
2:498:08How To Replace a 4 Stroke Throttle Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the long taper facing towards the end of the cable. And then we can take the body of it. We'reMoreWith the long taper facing towards the end of the cable. And then we can take the body of it. We're going to push the throttle cable in put the body over it like so.
How do you hook up a throttle cable to a pedal?
2:015:41How to install universal billet pedals and convert to a throttle cable in a ...YouTubeStart of suggested clipEnd of suggested clipThe cables coming out how the this cable mounts to the pedal lover is with these this pin right hereMoreThe cables coming out how the this cable mounts to the pedal lover is with these this pin right here and then this cotter pin. As you can see there's on the side of this lever. There's three holes.
How do I speed up my EZ Go gas golf cart?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you make a gas golf cart go faster?
How to Make Your Gas-Powdered Golf Cart Faster [Updated, 2022]1 Use A Better Golf Cart Battery.2 Increase Torque.3 Upgrade the Golf Cart Motor.4 Install a Torque Converter.5 Install a Higher-Performance Clutch.6 Tweak The Governor.7 Install A Cold Air Intake.8 Get Bigger Golf Cart Tires.More items...•
How can I increase the speed of my golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you remove a throttle cable from a slide?
3:255:03Throttle Cable Removal Mikuni TM28 Flatside - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo again i hold it with my thumb. If that does not come out you can grab the little tip with a pairMoreSo again i hold it with my thumb. If that does not come out you can grab the little tip with a pair of pliers. And then pull it out. And then wiggle the throttle.
How do you remove throttle cable from switch housing?
4:0913:24Harley Davidson Throttle Cable Install, Remove, Replace, RepairYouTubeStart of suggested clipEnd of suggested clipOff a little slit in it. And. Then it backs right off the cable. Don't lose those. And he's justMoreOff a little slit in it. And. Then it backs right off the cable. Don't lose those. And he's just doing the same exact thing to the return cable getting the ferrule out of there and removing.
How do I change throttle?
DifficultyOpen your hood and locate your engine's throttle body. ... Remove the air intake duct at the throttle body.Inspect the throttle body ports for carbon build up. ... Remove the throttle cable from the throttle body control lever. ... Disconnect any air or vacuum hoses from the throttle body.More items...
What is throttle cable?
The throttle cable plays a key role in ensuring smooth power delivery and acceleration of the cart. It ensures that your golf cart operation is smooth and safe. A throttle cable assists in the efficient utilization of the batteries and gas of the golf cart.
How to get a golf cart to idle?
Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle.
How to stop a cart from running at less speed?
Compress the spring between the cable stop and the throttle lever to close the throttle until the pedal is away from the microswitch so that the cart can run at less speed with very less throttle. You must do the compression until your problem goes off. Turn the key to the OFF position and press the accelerator pedal.
How to increase the speed of a golf cart?
Make sure that the governor and carburetor are seated with minimum slack and no tension. Fix the cable in place by tightening the nuts at the end of the cable. As the length of the throttle cable increases, it stops the throttle lever from being pulled back. This will in turn increase the speed of your golf cart.
What to do if throttle plate opens before it should?
If the throttle plate opens before it actually should, loosen the rear cable. If the throttle plate opens at the correct time but only partly, tighten the rear cable. If the throttle plate opens before it actually should but only partly, loosen the front cable and then tighten the rear cable.
How to adjust idling on a golf cart?
Press the accelerator so that the golf cart starts up and begins to idle. Check the cable tension to make sure that it’s still loose. The idle screw can be used to adjust the idling if it’s very fast. Turn the key to the OFF position and put the cable back into the box.
How to run a cable to a governor?
Slide the cable through the little slit present on the side of the cart. Position the cable so that the wire part is in the spool. This ensures that the threaded part of the cable rests on the adjuster bracket. Move the housing backward and adjust the nut to where it was initially. Finally, run the cable to the governor as it was at the start.
Do E-Z-Go Golf Carts have titles?
E-Z-Go Golf Carts, unlike vehicles, do not have a title, but they do have serial numbers. If you are buying a golf cart, it is essential to check the serial number to ensure you do not buy a stolen one. Each E-Z-Go Golf cart has a unique serial number that you can use to identify your golf cart.
Where is the E-Z-Go Cart Serial Number
As mentioned above, all E-Z-Go Golf carts have unique serial numbers. These numbers are essential when buying replacement parts for your golf cart. Textron Specialized Vehicles has been building golf carts for a long time, and the serial numbers are placed on different parts of the golf carts.
How do I push my E-Z-Go Golf Cart?
It can be frustrating when your battery is flat and your golf cart will not roll. To push it to the nearest charging or gas station, you need to release the motor brake. Follow these easy steps to do that.
Why does my E-Z-Go golf cart not move
There are several reasons why your cart refuses to move, but you should check the battery before anything else. If the battery is charged, here are some other reasons why your golf cart will not move.
Are all E-Z-Go Golf carts electric?
No, there are both electric and gas-powered E-Z-Go Golf carts available. Bear in mind that there are several models you can drive on the street, but those are all-electric. These electric models run on batteries that you have to charge at least every 24 hours, depending on how much you use them.
How to tell the Assembly year of my E-Z-Go golf cart
The placement of serial numbers is discussed above, and you will find the manufacturer’s number right next to it. The manufacturer’s number consists of one letter and 3 or 4 numbers. The last two numbers indicate the last two digits of the year of assembly.
How to service E-Z-Go Golf Cart
Like all vehicles, E-Z-Go golf carts require regular maintenance to enhance longevity and performance. You should ensure that your golf cart is serviced after every six months of use. That will ensure that you spot problems and repair them early, which will help reduce repair costs. Here are essential guidelines for E-Z-Go golf cart maintenance.
How to change motor on Ezgo cart?
How to change the motor on a Electric EZGO: The first step is to remove the wires connecting the battery pack to ensure that the cart has no power. It is advisable to use protective gloves. Do not use wristwatch, rings or jewelry.
How to remove the engine on a 2001 Ezgo?
Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How to yank a cart motor out?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
How to remove PDS motor?
Here are the steps to remove a PDS motor: You must first put the Run-Tow/Maintenance switch to Tow/Maintenance. Disconnect the wires connecting the battery. Disconnect and remove all the wires and cables connected to the motor. You should then remove the snap ring and the speed sensor from the motor end cover.
Why is it so hard to remove a golf cart motor?
On most occasions, the difficulty in removing the motor from its place in a golf cart is due to the rust that would have developed all around. It won’t come off so easily and you can’t use too much force as it may damage some of the other parts.
Can you pull an EZGO cart up?
For starters, the input shaft could be jammed or broken, making it difficult for you to pull the motor up. You can use a hammer mildly to slowly tap and pull it off the hold and pull it up. The other issue you may face with the older models of EZGO carts is where the motor could be welded to the body.
How to remove clutch on EZGO golf cart?
How to remove a secondary clutch on an EZGO golf cart. First of all, make sure that the golf cart is turned off, and the brake is in place. Make sure to put pressure on the gas pedal. Use a clutch puller to remove the drive belt. Loosen the central bolt using an air gun.
What to do if you have a problem with your G16 golf cart?
If there is any problem with the secondary clutch, it is best to replace it or the drive belt connected to it. If you are unsure about removing the drive belt or the clutch, then you can adjust it.
How to remove secondary clutch on Yamaha golf cart?
Just carefully follow the given steps: First of all, identify the right clutch puller according to the VIN number of the golf cart you are operating.
Why does my golf cart clutch slip?
There can be a problem with the drive belt, which can cause the clutch to slip. Sometimes the installed belt drive may not match the clutch in the golf cart, causing problems. Just replace it, and you are good to go. Check if the belt drive is misaligned. This is also a common problem with the clutch.
What is wrong with my golf cart clutch?
If there is any problem in how your golf cart runs, you can check for the following problems: There might be a problem with the belt. Check if the belt is too tight or loose.
How to find primary clutch on golf cart?
There are two clutches in the golf cart. To locate the primary clutch, it is generally the lower one. Consult the cart’s manual to make sure. First, observe exactly how the drive belts have been adjusted to the clutches. After you have noted that.
What to do if clutch gets stuck?
If that is the case, then you will need to complete the following steps: If the clutch gets stuck in any instance, the first thing you should do is use a PB Blaster and add some of it to the clutch. Give it some time to soak.
