Switch the engine OFF after parking the golf cart. Allow the engine to cool, if it has been running for some time. Remove the engine cover. You will be able to see the drive belt now. Use an open-end wrench to loosen the drive belt tension bolt. This bolt is on the front clutch pulley. Remove the drive belt by sliding it off the front pulley.
Full Answer
How to replace a drive belt on a golf cart?
Stretch the belt over the front pulley. You will have to pull the front clutch pulley a little forward to create tension on the belt. Tighten the tension bolt using a wrench. Now your Club Car golf cart has a new drive belt and you will be able to feel the difference when you drive the cart around.
How do I know if my golf cart drive belt is bad?
The best test to see if a golf cart drive belt has the correct tension is to use the Finger Test. Press the drive belt with one finger at its center between the two clutches. It should sag by just an inch and a half. Another method suggested by an expert is to go for a drive belt that is 1-inch shorter than the stock belt in your cart.
How to replace a clutch on a golf cart?
Switch OFF the golf cart’s engine. Take a screwdriver and gently insert it between the belt’s bottom and the clutch’s groove. Slowly rotate the clutch and the belt will come off easily. If the belt is already loose, taking it out is very easy.
What to do if your 1997 club car drive belt is slipping?
When a 1997 Club Car drive belt is slipping, first make sure that it is the drive belt that is at fault. You may have to remove the cover and watch the clutches in action while the cart is in motion to make sure that it is indeed the drive belt that is slipping. You will have to change the drive belt as there is no other alternative to it.
How do you tighten the belt on a Yamaha golf cart?
0:002:03How to tighten a loose Starter Belt on Yamaha Golf Cart YDRA. G29YouTubeStart of suggested clipEnd of suggested clipAnd wiggle this belt here yeah she's loose. All right my 12 mil uh socket here grab that loosen thatMoreAnd wiggle this belt here yeah she's loose. All right my 12 mil uh socket here grab that loosen that up 17 mil wrench here wrap this down. There you go.
How do you change a drive belt on a 2007 Yamaha Golf Cart?
0:462:46Yamaha Drive Belt | How to Install on G29 Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it overMoreNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it over the top of this outer chief like this just slowly roll it over. And. It will come right.
How do you change a drive belt on a Yamaha g14 golf cart?
0:352:32HOW TO CHANGE A DRIVE BELT ON YAMAHA GOLF CART OR ANY ...YouTubeStart of suggested clipEnd of suggested clipJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spinMoreJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spin the back off.
How do you tighten a clutch belt on a golf cart?
There is no provision for adjusting the drive belt on a Club Car golf cart. If you find the belt loose or too tight, you have to go for a replacement belt. Choosing the right belt and ordering can pose a challenge. You will need to order a drive belt that is 1-inch shorter than your stock belt.
How tight should a golf cart starter belt be?
The drive belt should not be too tight. If it's too tight it can risk wearing off faster and it's also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger.
How do you install a secondary clutch on a Yamaha golf cart?
6:1216:27Yamaha Drive G29 and Drive 2 Clutch Kit Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut i have seen a lot of guys just make something with stuff that they have laying around the garageMoreBut i have seen a lot of guys just make something with stuff that they have laying around the garage. Now it can be as simple as just using a piece of angle iron. And a piece of all thread.
How do I fix my golf cart belt?
2:255:57Changing the Drive Belt and Starter Generator Belt 2008 EZGO TXTYouTubeStart of suggested clipEnd of suggested clipJust. First put the belts on and then tilt the starter generator as far as you can and tighten thatMoreJust. First put the belts on and then tilt the starter generator as far as you can and tighten that nut up. By hand first and then use the wrench to get it a little bit.
How wide is a Yamaha Golf Cart belt?
1-3/16″ wideBelt size is 1-3/16″ wide x 39″ long.
How do you remove a starter from a Yamaha golf cart?
How to Remove, Wire & Test a Golf Cart Starter Generator Disconnect the negative battery cable. Loosen and then remove the top and bottom bolts of your starter generator. Remove the belt of your starter generator and leave it around the engine. Loosen all of the wiring and remove them each by hand.More items...
How does a golf cart clutch work?
0:463:28How a golf cart CVT slip drive clutch works - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutchMoreAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutch.
How do you tighten the belt on a club car starter?
6:459:16Club Car DS Tune Up Kit | Starter/Drive Belt - YouTubeYouTubeStart of suggested clipEnd of suggested clipBelts are that easy now that we got the belts changed let's say we're going to do on this turn upMoreBelts are that easy now that we got the belts changed let's say we're going to do on this turn up it's go ahead we're going to check the valves. See if they need adjusting.
Do golf carts have transmissions?
All golf carts (much like cars) have a clutch, which is the part of the drivetrain that helps the put the power of the motor down through to the wheels/ground. Golf cart clutches are a part of the Continuously Variable Transmission (or CVT).
How do you change a drive belt on a golf cart?
1:195:57Changing the Drive Belt and Starter Generator Belt 2008 EZGO TXTYouTubeStart of suggested clipEnd of suggested clipDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back.MoreDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back. Until it pops off that rear driven clutch and then take it right out.
How do you measure a golf cart belt?
0:002:04How to measure for a go-kart drive belt. - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover. Now the first measurement we're going to take on this is we're going to measure from theMoreCover. Now the first measurement we're going to take on this is we're going to measure from the centerline of the crankshaft. To the centerline of the jack shaft.
How do you remove a starter from a Yamaha golf cart?
How to Remove, Wire & Test a Golf Cart Starter Generator Disconnect the negative battery cable. Loosen and then remove the top and bottom bolts of your starter generator. Remove the belt of your starter generator and leave it around the engine. Loosen all of the wiring and remove them each by hand.More items...
How does a golf cart clutch work?
0:463:28How a golf cart CVT slip drive clutch works - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutchMoreAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutch.