Most importantly, when removing a clubhead from a graphite shaft it is imperative that the clubhead be removed by pulling it straight off of the shaft. Twisting and pulling on the clubhead to remove it from the shaft (like you would on a steel shaft) will result into a shaft tip failure. A graphite shaft puller is an absolute must for this job.
How to remove a head from a golf shaft?
However, if you do heat the club with it in the shaft puller, make sure to heat the rear of the hosel. If you do discolor the head, at least it will be on the back side that it least likely to be seen by the golfer when the club is at address. You are now ready to apply heat to the head for the purpose of removing the head from the shaft.
How to remove a clubhead from a graphite shaft?
Most importantly, when removing a clubhead from a graphite shaft it is imperative that the clubhead be removed by pulling it straight off of the shaft. Twisting and pulling on the clubhead to remove it from the shaft (like you would on a steel shaft) will result into a shaft tip failure. A graphite shaft puller is an absolute must for this job.
How do you fix a broken shaft on a golf club?
Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel.
How do you remove epoxy glue from a golf club?
Scrape down toward the head and away from your body. Insert the golf club into a shaft clamp and tighten it. Apply a heat gun to the hosel to melt the epoxy glue. The hosel is the area at the base of the clubhead where the shaft is inserted. Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft.
How do you remove driver head shaft?
2:415:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipHot. Pull it straight off all the way. Once you get it down to the bottom basically it'll come rightMoreHot. Pull it straight off all the way. Once you get it down to the bottom basically it'll come right off. And there you have it.
How do you remove golf club shafts from a graphite shaft?
0:552:37How to cut off and remove a golf grip from graphite shaft ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd if you can see that properly on there on the camera i'm literally just scratching slash scoringMoreAnd if you can see that properly on there on the camera i'm literally just scratching slash scoring this rubber. Hopefully if i give it a good pull. Now it should come off there we go.
How do you replace a graphite shaft on a driver?
4:297:38How to Install Graphite Golf Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe butt of the shaft on a hard surface to ensure the shaft is installed to the bottom of the hosel.MoreThe butt of the shaft on a hard surface to ensure the shaft is installed to the bottom of the hosel. Remove the head and place some epoxy inside the hosel dip the tip of the shaft into the epoxy mix.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
Can you use acetone on graphite shafts?
Wipe the shaft with acetone after you have removed the tape. This will help further clean the shaft, as well as remove the mineral spirit residue.
How do you remove adhesive from golf shaft?
2:505:54How to get stickers & glue off you golf shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're gonna get rid of that this is all you need hot water goo gun and a dry piece of paper towelMoreSo we're gonna get rid of that this is all you need hot water goo gun and a dry piece of paper towel you don't want to use the wet light because you want to rub the glue gun on the goop.
How do you remove a golf club head?
Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.Remove the ferrule. ... Place the club in a vise to position it for shaft removal. ... Heat the glue inside the hosel. ... Clean excess glue out of the hosel to make a comfortable fit for the new shaft.
How do you replace a driver head?
1:465:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp as that shaft heats the epoxy starts to break down. And then the shaft the head of the club willMoreUp as that shaft heats the epoxy starts to break down. And then the shaft the head of the club will come will pull off of that shaft. Once that epoxy gives way then you can turn your heat gun.
How do you remove a broken graphite shaft from club head?
1:357:16Removing a Broken Graphite Shaft 2019 -Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this kind of shaft extraction is no different alright so the easiest way that I have found isMoreAnd this kind of shaft extraction is no different alright so the easiest way that I have found is you have to heat up this area and then you step drill.
How do I make a graphite shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do you remove graphite shaft from hosel?
0:515:54How to Remove a Graphite Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo using a heat gun on high. I'm gonna heat the just the Ferro part and then cut it off with a knifeMoreSo using a heat gun on high. I'm gonna heat the just the Ferro part and then cut it off with a knife. It's ready to cut off because you'll kind of see it start to melt.
How do you cut a graphite golf shaft at home?
1:1514:05Golf Club Repair - How To cut a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you don't have a you don't have all the money to do something like that. And or going to buy in aMoreSo you don't have a you don't have all the money to do something like that. And or going to buy in a in a a cutting wheel of sorts. So how do you get it done without. It.
How do you remove golf club shafts?
0:042:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do you remove graphite shafts from an iron?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
How do I make a graphite shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do you remove a ferrule from a graphite golf shaft?
0:223:50How to Remove Ferrule from Steel Shaft Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become aMoreGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become a bit more smooth-looking kind of like. You know it's getting warm honestly. Does not take. Much.
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How to get glue out of a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue. As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force.
How to get rid of loose glue?
Twist it to remove loose glue. A small amount of mineral spirits will help clean out the area.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to catch a club head off a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
Can you pull a pro launch shaft by hand?
I have pulled a few by hand, never anything high end so if it didn't work no biggie. I did mess up the tip of a Pro Launch shaft, just trimmed it and used it in a 5 wood. Did another that was a mess, had to drill it out and throw the shaft away, but I have had several others where I had no issues. It's risky, but it can be done.
Can you pull graphite shafts without a puller?
Pulling a graphite shaft without a shaft puller is almost a guaranteed way to ruin a shaft. You might get lucky and not damage it, but not something I would risk. If someone said here is a shaft to use and by the way, I pulled it by hand, I would pass on it.
How to twist a golf club head?
Remove heat from the hosel and twist the club head counterclockwise. It should twist off fairly easily. If it does not, apply more heat.
How to remove graphite from hosel?
Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
