
How to Remove a Shaft from a Head on a Golf Club
- Put on protective gloves and keep them on until the procedure is complete.
- Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. ...
- Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft.
- Allow the club head to cool completely once its been liberated from the shaft.
- Roll up a small piece of sandpaper and use it to clean out any remaining epoxy residue inside the hosel joint, making it ready for the insertion of ...
How do you get rust off a golf club head?
Step 1: Things You'll Need
- Fine Steel Wool
- Hard bristle toothbrush
- Wet and Dry sandpaper (as fine as you can get it)
- White Vinegar
- Metal Polish
- A bucket
- A Dremel or similar rotary tool with a polishing bit (not necessary, rags will do)
- Plenty of elbow grease!
How to clean a golf club the right way?
How to Clean Golf Clubs
- Gather Cleaning Materials. What do you need to clean golf clubs at home? ...
- Get Sudsy. Squirt a little of the dishwashing liquid into the bottom of your plastic bucket, then add warm water to create suds.
- Place Your Irons In the Bucket. ...
- Clean Out the Grooves. ...
- Rinse Off the Clubhead. ...
- Dry the Clubhead and Shaft. ...
- Cleaning Woods. ...
How do you clean rust off of golf clubs?
Steps on how to clean rust off golf clubs
- Pour the vinegar into the bucket. The vinegar should be enough to cover the entire clubhead when dipped into the bucket. ...
- Start scrubbing. While the clubhead is dipped into the vinegar, cup your hand to splash some vinegar to the shaft. ...
- Sand the deeply rusted parts. ...
- Brush the grooves. ...
- Clean the handle. ...
- Wipe and dry. ...
- Buff it. ...
How to regrip a golf club?
- How to Regrip Golf Clubs 1. Take Off the Old Grip 2. Add Grip Tape 3. Apply Solvent Solution 4. ...
- How to Choose the Right Golf Grips to Regrip Your Golf Clubs Size Firmness Weather Conditions Texture
- Types of Golf Grips Wrapped Corded Rubber Hybrid
- Cleaning Golf Grips
- When to Regrip Golf Clubs
- Signs Your Club Grips Need to Be Replaced
- Final Thoughts

How do you remove the shaft from an iron head?
How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...
How do you remove a wedge head from a shaft?
As you apply heat to the hosel (by keeping the heat moving around the whole area), you should periodically try and twist the head and shaft. If they don't budge, keep applying heat. Eventually you will feel the epoxy break and will be able to twist the head off.
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you remove a hosel from a golf shaft?
0:433:32How to Remove a Graphite Shaft Broken Off at the Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy scads to protect the club. Head I want to clamp it make sure to clamp it tight but not too tightMoreBy scads to protect the club. Head I want to clamp it make sure to clamp it tight but not too tight if I'm gonna crush the top of the housing. Now you're gonna need a few other things.
How do you replace club heads?
1:4010:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipProbably start off on high but you want to move it around on actual the hostile here kind of andMoreProbably start off on high but you want to move it around on actual the hostile here kind of and spinning it around a little bit and make sure you get this superhot.
Can you put a new driver head on an old shaft?
The only way to know if we can put your old fitted shaft into a new head it to pull the shaft, weight the head and test the new head with the old shaft. The head may be heavier or lighter, the hosel dimensions may be off which could cause a length issue.
What glue is used to attach golf club heads?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
How do you replace a iron head on a golf club?
2:3522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How do you reattach a driver head to shaft?
0:236:41HOW to FIX your GOLF CLUB if the HEAD comes off | Easy TutorialYouTubeStart of suggested clipEnd of suggested clipIf you want to just make sure you're getting the right thing basically just one side hardener. AndMoreIf you want to just make sure you're getting the right thing basically just one side hardener. And one side resin. And they mix together to form a really strong bond.
How do you remove a bore through the shaft?
2:1313:16How To pull bore thru Golf Shafts, Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd that goes right on over here and it acts as the buffer to pull so I don't dent the top of theMoreAnd that goes right on over here and it acts as the buffer to pull so I don't dent the top of the head with my shaft puller. Ok. So that's what this does.
How do you remove a golf ferrule?
0:223:50How to Remove Ferrule from Steel Shaft Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become aMoreGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become a bit more smooth-looking kind of like. You know it's getting warm honestly. Does not take. Much.
How do you replace a hosel?
3:024:36SHAFT INSTALL In Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext apply epoxy to the tip of the shaft. Be sure to get good coverage over the tip of the shaft.MoreNext apply epoxy to the tip of the shaft. Be sure to get good coverage over the tip of the shaft. Install the shaft into the hosel bore slowly rotating or twisting the shaft as it goes into the hosel.
How to install a new shaft on a golf club?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris. Make sure that the hosel is totally clean before you begin installing your new shaft.
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
How to catch a club head off a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
How to get the head off a golf club?
Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.
Is a stock shaft good for golf?
Golf shafts come in a variety of materials, flexes and specifications. Often, the stock shaft is not the best choice for your particular game. You may remove the original shaft and replace it with one that more closely fits your abilities. When considering a new shaft, note features such as weight, length, kick point and flex.
How to twist a golf club head?
Remove heat from the hosel and twist the club head counterclockwise. It should twist off fairly easily. If it does not, apply more heat.
How to remove graphite from hosel?
Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
How to get epoxy off of a clubhead?
Apply pressure to the clubhead, while applying heat to the hosel at the same time. Continue doing this until the epoxy bond has softened and the clubhead comes off easily.
How to make a golf club with masking tape?
Step 1. Completely cover the head of the club with masking tape to prevent the head from being scratched during the process. Now, place the club in the vise, so that the middle of the shaft is the part being held in the vise. Make sure the club is held securely.
How to get ferrule off of a car?
Take the utility knife and cut off the small plastic piece at the base of the shaft , also called the "ferrule." If the ferrule doesn't come off easily, use the butane torch to heat it a bit, and then it should come right off.
Can you replace a golf club shaft instead of replacing the entire club?
By Tami Fisher. Replacing a golf shaft instead of replacing the entire club can save money. Once in a while, something happens to cause a golf club shaft to splinter or even break. When this happens, the old shaft must be removed and a new one installed in its place.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
