- Put on protective gloves and keep them on until the procedure is complete.
- Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. ...
- Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft.
- Allow the club head to cool completely once its been liberated from the shaft.
- Roll up a small piece of sandpaper and use it to clean out any remaining epoxy residue inside the hosel joint, making it ready for the insertion of ...
How do you remove a broken putter head?
Submerge the putter head (make sure the entire hosel is submerged) in the ice bath Take it out, dry it quickly, and hit it with the propane torch mentioned in the “standard” shaft removal method below.
How do you remove putter grips?
One of the most common ways to remove and add on a putter grip is to use an air compressor. Most golfers tend to use a 120 volt or higher air compressor to have the grips removed. It works by increasing the size of the grip and allowing it to slide down from the shaft.
How do you remove epoxy from a golf club head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
What do you use to clean your putter shafts?
I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc. If you have an old Ping Putter… The way these are built makes it difficult to remove their shafts. I suggest doing the following to get around this: Submerge the putter head (make sure the entire hosel is submerged) in the ice bath
How do you remove a golf club head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you remove iron head shaft?
How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...
Can you change a putter shaft?
Even putter shafts can wear down over time. People often like to change the shaft in their golf club, whether it's because the current one broke or because they want to try out the newest one on the market without purchasing a new club. To help save money, this is a task anyone can do with the right tools.
How do you remove club head from graphite shaft?
0:194:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you replace a iron head on a golf club?
2:3122:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How much does it cost to Reshaft a putter?
A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like. The cheapest shafts you can get are somewhere around 10 bucks each.
How much does it cost to replace a shaft on a putter?
Putter shafts can be $10.00 to replace, and they can be $400 to replace. The actual labor of replacing the shaft should cost around $20 or less.
Are all putter shafts the same?
The first thing you need to know is that all putter shafts flex some amount during the stroke. This adds a variable to the putting stroke we'd rather not have. That's why stiffer is better with putter shafts; the stiffer a putter shaft, the better it should perform.
How do you remove a putter shaft?
1:4611:49THE SHOP: How to replace a putter shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if it's a graphite shaft you would if we want to use a heat gun and a shaft puller. And then justMoreSo if it's a graphite shaft you would if we want to use a heat gun and a shaft puller. And then just give it a twist and it'll break the epoxy. And pop right off.
How do you remove graphite shaft without a shaft puller?
0:015:40How to Remove a Golf Shaft | DIY project Graphite Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipActually you just set it in device uh hit this power out with the gun. All through it the hustle.MoreActually you just set it in device uh hit this power out with the gun. All through it the hustle. And then once it's really heat up then you started i can start uh just pushing it.
How do you remove a graphite shaft at home?
0:556:40pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steelMoreNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steel on steel I don't see anything wrong with it it's just a much bigger. Application of the heat.
How to prepare a club head for a new shaft?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris.
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
Can You Remove a Putter Grip and Reuse It?
Most people believe you’ll need to replace the putter grip if it’s removed completely. However, it’s possible to remove the grip and reuse it. However, it’s important to note you may not get the full benefit of reusing golf putter grips compared to new grips. That will depend on the level of traction and wear that the grip has.
How Do You Remove Golf Grips Without Destroying Them?
Golf grips can be easily removed and reused. If they’re in good condition, you’ll be able to remove them without causing damage. However, if the grips are worn-out, damaged, or old, you’re the best option is to cut them off.
Materials Used for Removing Grip Solvent
Getting rid of the old putter grip can be tricky. However, many materials can be used to eliminate the grip solvent.
What Can I Use As Grip Solvent?
Replacing your golf grips can save you a lot of money. This skill can come in handy when you don’t have the time to take your clubs to a professional golf repair shop. There are a few types of solvents that you can use. The safest and most versatile one is the traditional golf grip solvent.
How Long Does It Take for Grip Solvent to Dry?
Generally, it takes the grip solvent about 4 hours to dry. The adhesive melts on the insides of the grip. As a result, the double-sided tape is joined onto the grip creating a strong bond.
How Long Does It Take to Regrip a Putter?
Re-gripping, the putter, can be done at home, and you won’t need to pay a lot of money for a professional club repairer to do it for you. In general, it’ll take about 4 hours since that’s how long it takes for the new adhesive on the tape to dry off.
How To Remove Putter Grip – Conclusion
Now that you know how to remove the putter grip without damaging it and you know how to install new ones (or reuse old ones), you’ll always have a good grip for your putters. Putting allows you to sink the golf ball into the hole with as few strokes as possible. There’s nothing more frustrating than to take a few extra attempts due to poor putting.
Step 1
Put on protective gloves and keep them on until the procedure is complete.
Step 2
Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense heat evenly on all sides of the hosel and don't be alarmed if small amounts of white smoke begin to escape the hosel cavity. That is just the old epoxy melting.
Step 3
Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.
Step 4
Allow the club head to cool completely once its been liberated from the shaft.
Step 5
Roll up a small piece of sandpaper and use it to clean out any remaining epoxy residue inside the hosel joint, making it ready for the insertion of a new shaft.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
Series Navigation
In the world of refinishing, this is by far the most important preliminary step. After years of use, golf clubs will get beat up, and in order to make them appear “new,” it is important to remove these signs of use. When I first began learning how to refinish golf clubs, it took me a while to learn how to do this.
Materials Needed
Protective Gloves (preferably not baggy ones like I’m unfortunately using in the video) and Eye-wear
About the Author: Zach Gollwitzer
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
