How to Remove a Shaft from a Head on a Golf Club
- Step 1. Put on protective gloves and keep them on until the procedure is complete.
- Step 2. Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense...
- Step 3. Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head...
How do you get rust off a golf club head?
Step 1: Things You'll Need
- Fine Steel Wool
- Hard bristle toothbrush
- Wet and Dry sandpaper (as fine as you can get it)
- White Vinegar
- Metal Polish
- A bucket
- A Dremel or similar rotary tool with a polishing bit (not necessary, rags will do)
- Plenty of elbow grease!
How to clean a golf club the right way?
How to Clean Golf Clubs
- Gather Cleaning Materials. What do you need to clean golf clubs at home? ...
- Get Sudsy. Squirt a little of the dishwashing liquid into the bottom of your plastic bucket, then add warm water to create suds.
- Place Your Irons In the Bucket. ...
- Clean Out the Grooves. ...
- Rinse Off the Clubhead. ...
- Dry the Clubhead and Shaft. ...
- Cleaning Woods. ...
How do you clean rust off of golf clubs?
Steps on how to clean rust off golf clubs
- Pour the vinegar into the bucket. The vinegar should be enough to cover the entire clubhead when dipped into the bucket. ...
- Start scrubbing. While the clubhead is dipped into the vinegar, cup your hand to splash some vinegar to the shaft. ...
- Sand the deeply rusted parts. ...
- Brush the grooves. ...
- Clean the handle. ...
- Wipe and dry. ...
- Buff it. ...
How to reshaft a golf club?
Update Your Golf Club With a New Shaft
- Steel Shafts: To remove a steel shaft from a metal wood or iron, place the shaft in a super lock tight shaft holder. Tighten the STSL in a vise. ...
- Measure the shaft tip. ...
- After the tip has been trimmed, abrade or roughen the shaft tip. ...
- Align the shaft graphics the way you want them by rotating the shaft. ...
- Position the club in the normal playing position. ...
How do you remove iron heads from shafts?
2:367:18Removing an iron shaft by hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn order to be able to apply the knife. And pull it down. All right now the reason why i'm tellingMoreIn order to be able to apply the knife. And pull it down. All right now the reason why i'm telling you this is i tried doing it without moving the ferrule.
How do you remove a club head from a steel shaft?
How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you change golf club heads?
0:272:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do you make a golf shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
What glue is used for golf club heads?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
How do you replace iron heads?
2:2522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How do you reattach a driver head to shaft?
2:0514:23LOOSE GOLF CLUB HEAD / How To Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipAhead put a little bit of epoxy. In that space between the ferrule. And the hosel squeeze them backMoreAhead put a little bit of epoxy. In that space between the ferrule. And the hosel squeeze them back together wipe it clean let it dry.
How do you reattach a iron Head?
0:006:41HOW to FIX your GOLF CLUB if the HEAD comes off | Easy TutorialYouTubeStart of suggested clipEnd of suggested clipIf you want to just make sure you're getting the right thing basically just one side hardener. AndMoreIf you want to just make sure you're getting the right thing basically just one side hardener. And one side resin. And they mix together to form a really strong bond.
How do you remove a club head from a graphite shaft?
0:314:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat are commercially available but they do essentially the same thing they securely clamp the shaftMoreThat are commercially available but they do essentially the same thing they securely clamp the shaft. And either push or pull the head straight off that's the key.
How do you remove a driver head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you replace a driver head?
0:045:16Golf Club Repair - Removing the driver head and cleaning & preppingYouTubeStart of suggested clipEnd of suggested clipWe can take the old shaft out of the shaft extractor here pretty easy to get the old shaft out justMoreWe can take the old shaft out of the shaft extractor here pretty easy to get the old shaft out just loosen up the screws. Take the protective film off the shaft. So you don't scratch it.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
How do you Reshaft a golf club at home?
2:3522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heatMoreUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How do you remove a ferrule from a golf shaft?
0:223:50How to Remove Ferrule from Steel Shaft Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd also your heat gun so plug bit of heat. Gently on the shaft. There's apply the heat. You'reMoreAnd also your heat gun so plug bit of heat. Gently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become a bit more smooth-looking kind of like.
Can you reuse steel golf shafts?
Continuously reusing graphite shafts is not a good habit either. Each time the shaft is exposed to a heat source, there has to be some effect to the shaft.
How to install a new shaft on a golf club?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris. Make sure that the hosel is totally clean before you begin installing your new shaft.
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
How to catch a club head off a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
How to remove a shaft from a golf club?
Using propane or a torch, heat the hosel of the club to remove the steel shaft from the club head. The heat will break the epoxy bond that holds the head to the shaft.
How to clean epoxy from golf club head?
Use a wire brush to clean out the remains of the old epoxy from the club head.
How long to hold a golf club shaft?
Insert the shaft into the club head. Hold the head and shaft together for approximately 30 seconds to secure.
How to wrap a golf grip?
Apply the double-sided grip tape to the length of the grip wrapping it around the shaft . Leave 1/2 inch overhang in order to fold in the end of the shaft.
When to remove head from shaft?
You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose. By doing so, this will limit the possibility of heat penetrating into the shaft and causing it to break down.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
How to protect a carbon head?
If this is the case, go to you local welding supply center and get a bottle of a product called Cool Gel. This is very cool stuff! Just spray it on the carbon surface only and it will protect it from any wayward heat like an accidental pass with the torch. When you are done, you can just wipe the head with a wet paper towel or rag to remove the gel.
Introduction – DIY Golf Shaft Pulling Tricks
We previously wrote about “ How to Pull a Golf Shaft ” where we cover the basic technique for properly and safely pulling both steel and graphite golf shafts. While that technique is a great best practice, and the only foolproof (-ish) safe way to pull graphite shafts, there are a few hacks you can use for pulling steel shafts at your home.
The Stove
This is the same technique as “by hand” but you use the stove for your heat source. I’ve been in a couple of random situations where I didn’t have a propane torch or heat gun at my disposal and had to pull a steel shaft from a head. All I did was fire up a burner on the stove and use it to heat the epoxy.
In a Vise
The vise technique is one of the great at-home DIY golf shaft pulling tricks. It’s not dissimilar to the “by hand” technique, but gives you a little more leverage and keeps your hands away from the heat. For this technique, you can approach in two different ways.
Boiling Water
This is my absolute favorite DIY golf shaft pulling trick based on ingenuity alone. What’s nice about this technique is that it works well and makes saving your sweet custom ferrules feasible as long as they weren’t super epoxied on. In order to do this, fill a pot with enough water to submerge your club head in.
Conclusion
Like I said in the intro, I’m going to recommend using traditional shaft removal techniques 100% of the time. You can find that approach here . That said, there are situations that may require an alternative approach and hopefully these DIY golf shaft pulling tricks will help you out there.
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
