How Do I Remove the Shaft of a Golf Club?
- Place the shaft, or what remains of it if it is broken, in a vise parallel to the floor. Secure the shaft in the vise.
- Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. ...
- Remove heat from the hosel and twist the club head counterclockwise. It should twist off fairly easily.
- Clean out any remaining epoxy in the hosel. ...
How do I clean up golf club shafts?
Oct 29, 2013 · https://www.hirekogolf.com - Have fun and learn how to repair or disassemble a steel-shafted golf club, while getting started in custom golf clubmaking in ju...
How do you replace a golf club shaft?
The following are some useful tips that will come in handy for you in a bid to help you learn how to remove the shaft from your golf club: Step 1. You will need to remove the ferrule from the club. This is the small elastic or plastic band that you will find just on top of the hosel. You will need a utility knife to remove it. However, try and be very careful with it so that you do not cause any …
How much does it cost to reshaft a golf club?
Twisting and pulling on the clubhead to remove it from the shaft (like you would on a steel shaft) will result into a shaft tip failure. A graphite shaft puller is an absolute must for this job. Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp ) to several hundred dollars for a hydraulic model.
How to reshaft a golf club?
So the order would be shaft clamp —> spring —> hosel protector —> club head. Of course in this setup the spring is fully compressed and applying that pressure to the business end of the setup. Now all you have to do is heat the hosel of the club head, and it should pop off without applying any additional force. 0 Paul Harrison 7 months ago
How do you remove a golf club shaft without a puller?
How do you remove a graphite golf club shaft?
How do you pull a steel golf shaft?
- Carefully clamp the shaft into a vise using a Shaft Vise Clamp. ...
- When removing steel shafts from clubheads, use a torch to heat the hosel. ...
- After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.
How do you separate a golf head from the shaft?
How do you make a golf shaft puller?
How do you use a shaft puller?
Can you change golf club shafts?
How do you remove driver shaft?
How much does it cost to replace a golf club shaft?
Can golf club shafts be reused?
Can I change the shafts in my irons?
Can you reuse shafts?
How to get glue out of a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue. As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
How to get rid of loose glue?
Twist it to remove loose glue. A small amount of mineral spirits will help clean out the area.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
How to get epoxy off of a clubhead?
Apply pressure to the clubhead, while applying heat to the hosel at the same time. Continue doing this until the epoxy bond has softened and the clubhead comes off easily.
How to get ferrule off of a car?
Take the utility knife and cut off the small plastic piece at the base of the shaft , also called the "ferrule." If the ferrule doesn't come off easily, use the butane torch to heat it a bit, and then it should come right off.
How to make a golf club with masking tape?
Step 1. Completely cover the head of the club with masking tape to prevent the head from being scratched during the process. Now, place the club in the vise, so that the middle of the shaft is the part being held in the vise. Make sure the club is held securely.
Can you replace a golf club shaft instead of replacing the entire club?
By Tami Fisher. Replacing a golf shaft instead of replacing the entire club can save money. Once in a while, something happens to cause a golf club shaft to splinter or even break. When this happens, the old shaft must be removed and a new one installed in its place.
Step 1
You will need to remove the ferrule from the club. This is the small elastic or plastic band that you will find just on top of the hosel. You will need a utility knife to remove it. However, try and be very careful with it so that you do not cause any damage on your club.
Step 2
Get a vice and secure the club properly. Make sure that you have something soft to protect the club from excessive force as you secure it to the vice, ensuring that you leave exposed around 8 inches off the shaft and the entire length of the head.
Step 3
Get some heat on the glue inside the hosel to melt it. You can do this with a propane torch. Do not crank the head of the club with too much force as you attempt to remove it. Applying too much force could actually break the club within the hosel.
Step 4
Clean off any of the glue that might have remained in the hosel so that you can get a proper and new fit for the shaft. To do this easily, get some sandpaper and roll it slowly until it fits into the hosel. Twist slightly and gently so that you can get rid of any loose glue.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
When to remove head from shaft?
You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose. By doing so, this will limit the possibility of heat penetrating into the shaft and causing it to break down.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
How to protect a carbon head?
If this is the case, go to you local welding supply center and get a bottle of a product called Cool Gel. This is very cool stuff! Just spray it on the carbon surface only and it will protect it from any wayward heat like an accidental pass with the torch. When you are done, you can just wipe the head with a wet paper towel or rag to remove the gel.
Can you remove graphite shafts?
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this.
Can you load a spring in a vise?
If you buy a spring that is larger on the inside than a shaft, you can load it in the vise to make the hosel protector apply continuous pressure to the club head.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
Can you pull a pro launch shaft by hand?
I have pulled a few by hand, never anything high end so if it didn't work no biggie. I did mess up the tip of a Pro Launch shaft, just trimmed it and used it in a 5 wood. Did another that was a mess, had to drill it out and throw the shaft away, but I have had several others where I had no issues. It's risky, but it can be done.
Can you pull graphite shafts without a puller?
Pulling a graphite shaft without a shaft puller is almost a guaranteed way to ruin a shaft. You might get lucky and not damage it, but not something I would risk. If someone said here is a shaft to use and by the way, I pulled it by hand, I would pass on it.
