How to Remove a Golf Shaft From the Head
- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How do you replace a broken shaft on a golf club?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise, making sure you don't damage it. Then use a hand drill to carefully remove the debris.
How do you remove epoxy from a golf club head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
Do you need a professional to reshaft a golf shaft?
It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly. Remove the ferrule.
How do you remove a ferrule from a golf club?
Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it. Place the club in a vise to position it for shaft removal. The club should lie horizontally. Make sure the vise grips the shaft securely to prevent it from slipping out. Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel.
How do you remove a shaft head?
As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force. The shaft could break off inside the hosel. Work the head free carefully and gradually until it comes off.
How do you remove iron heads from shafts?
2:447:18Removing an iron shaft by hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn order to be able to apply the knife. And pull it down. All right now the reason why i'm tellingMoreIn order to be able to apply the knife. And pull it down. All right now the reason why i'm telling you this is i tried doing it without moving the ferrule.
How do you remove a wedge head from a shaft?
As you apply heat to the hosel (by keeping the heat moving around the whole area), you should periodically try and twist the head and shaft. If they don't budge, keep applying heat. Eventually you will feel the epoxy break and will be able to twist the head off.
How do you remove a hosel from a shaft?
0:503:32How to Remove a Graphite Shaft Broken Off at the Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipI might push in the stop at the bottom of the hosel.MoreI might push in the stop at the bottom of the hosel.
How are golf club heads attached to the shaft?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
How do you replace a iron head on a golf club?
2:3122:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
Can you put a new driver head on an old shaft?
The only way to know if we can put your old fitted shaft into a new head it to pull the shaft, weight the head and test the new head with the old shaft. The head may be heavier or lighter, the hosel dimensions may be off which could cause a length issue.
How do you make a golf shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do I remove a golf shaft adapter?
0:139:32How to Remove Golf Shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to prepare a club head for a new shaft?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris.
Where did Bill Herrfeldt graduate from?
Bill Herrfeldt specializes in finance, sports and the needs of retiring people, and has been published in the national edition of "Erickson Tribune," the "Washington Post" and the "Arizona Republic." He graduated from the University of Louisville.
Step 1
Put on protective gloves and keep them on until the procedure is complete.
Step 2
Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense heat evenly on all sides of the hosel and don't be alarmed if small amounts of white smoke begin to escape the hosel cavity. That is just the old epoxy melting.
Step 3
Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.
Step 4
Allow the club head to cool completely once its been liberated from the shaft.
Step 5
Roll up a small piece of sandpaper and use it to clean out any remaining epoxy residue inside the hosel joint, making it ready for the insertion of a new shaft.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How to clean epoxy from hosel?
Clean out any remaining epoxy in the hosel. Begin using a file and scrape away the residue, then apply a solvent to a small rag and wipe down the interior of the hosel. You may want to push the rag in with the tip of a screwdriver or similar tool.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
