How to Remove a Golf Shaft From the Head
- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How do you replace the shaft on a golf club?
Steps to Replace a Golf Club Shaft at Home
- Choosing the Right Golf Club Shaft. To begin with, you will need to get your hands on a golf club shaft. ...
- Cleaning the Club. Now, take out your utility knife. ...
- Taking the Shaft Out. It is now time to release the head from the shaft. ...
- Scrapping off Any Residuals. ...
- Installing a New Shaft. ...
- Finishing Touches. ...
How do you remove a golf shaft?
Removing a Rear Drive Shaft – This is how you do it
- Mark the Drive Shaft and Remove the Bolts. To know how to remove drive shaft, getting the exact estimation of drive shaft is necessary before beginning the process.
- Eliminate the Drive Shaft Flange. Drive shaft flange can be easily removed by gently shocking with a plastic hammer. ...
- Take out the Drive Shaft. ...
- Reinstall the Drive Shaft and Other Parts. ...
How to remove a golf shaft without a puller?
How to Remove a Golf Shaft From the Head
- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How to repair a broken Golf Club shaft?
Club Repair services
- Re-shaft broken irons from £28.00
- Re-shaft Hybrids from £50.00
- Re-shaft Woods from £60.00
- Drill out broken iron heads and re-shaft £35.00
- Loft & Lie Adjustments per club £3.00
- Swingweight Adjustments per club £5.00
- Extend Graphite shafts saving grips per club £10.00
- Extend steel shafts saving grips per club £8.00
- Shorten Clubs and save grips per club £6.00
How do you remove a golf head from a steel shaft?
How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...
How do you remove a golf shaft at home?
0:172:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do I remove a shaft adapter without a puller?
1:594:14Simple Taylor Made shaft adapter removal 30 sec without shaft pullerYouTubeStart of suggested clipEnd of suggested clipAll right take the head on see that moves really easy and so you just keep kind of twisting. AndMoreAll right take the head on see that moves really easy and so you just keep kind of twisting. And pulling keep the head locked in and eventually it will come all the way. Off.
How do you pull a graphite golf shaft?
0:483:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut it in quickly. Don't go too tight you wanna just make sure that it's snug because again if youMorePut it in quickly. Don't go too tight you wanna just make sure that it's snug because again if you crush this thing it's useless. Now you want to Snug it. Up.
How do you make a golf shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do I remove a golf shaft adapter?
0:119:32How to Remove Golf Shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.
How do you remove graphite shaft without a puller?
3:205:40How to Remove a Golf Shaft | DIY project Graphite Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipDefinitely use a um a rubber hammer.MoreDefinitely use a um a rubber hammer.
What is a golf shaft adapter sleeve?
Shaft Adapter Sleeves allow you to mount or change the heads on your shafts. The shaft adapter is usually used on drivers or woods but can be used on the golf club shaft of your choice.
How do you remove a broken graphite shaft from driver head?
1:357:16Removing a Broken Graphite Shaft 2019 -Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this kind of shaft extraction is no different alright so the easiest way that I have found isMoreAnd this kind of shaft extraction is no different alright so the easiest way that I have found is you have to heat up this area and then you step drill.
How do you use a shaft puller?
2:226:40pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipQuick. Okay after we put the heat to it you want to put it into the puller really fast and then youMoreQuick. Okay after we put the heat to it you want to put it into the puller really fast and then you want to hold on to the head that you just got out.
Can you reuse graphite golf shaft?
Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely. The only way a graphite shaft will become unusable aside from some freak accidents is by human error in part of the build or an out of control temper on the course.
How do you remove a driver shaft?
0:344:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How do you change a golf club shaft?
0:5210:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actualMoreThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actual end of the golf club or the iron. Before you actually put the new shaft in you'll need a ferrule.
How do you pull a fairway wood shaft?
1:054:56Club Building 101: Pulling a Shaft from a Bonded Driver - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet it set up. And you'll see that it's already starting to push the ferrule. That's fine startingMoreGet it set up. And you'll see that it's already starting to push the ferrule. That's fine starting to really mush. It.
How do you change a driver shaft?
0:335:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so we lay it in in this little groove right here. Which is going to slide back and forth andMoreTool so we lay it in in this little groove right here. Which is going to slide back and forth and put pressure and pull on the head. As the shaft is heated. Then we tighten the shaft.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to catch a club head off a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
How to heat a hosel?
Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense heat evenly on all sides of the hosel and don't be alarmed if small amounts of white smoke begin to escape the hosel cavity. That is just the old epoxy melting.
How to get the head off a golf club?
Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.
Where did Izzy Barden go to college?
He was awarded the Russ Morrison Golf Scholarship in Santa Barbara, Calif., where he attended Santa Barbara City College to study journalism and later dentistry at University of California, Los Angeles.
Is a stock shaft good for golf?
Golf shafts come in a variety of materials, flexes and specifications. Often, the stock shaft is not the best choice for your particular game. You may remove the original shaft and replace it with one that more closely fits your abilities. When considering a new shaft, note features such as weight, length, kick point and flex.
How to twist a golf club head?
Remove heat from the hosel and twist the club head counterclockwise. It should twist off fairly easily. If it does not, apply more heat.
How to remove graphite from hosel?
Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
How to get epoxy off of a clubhead?
Apply pressure to the clubhead, while applying heat to the hosel at the same time. Continue doing this until the epoxy bond has softened and the clubhead comes off easily.
How to get ferrule off of a car?
Take the utility knife and cut off the small plastic piece at the base of the shaft , also called the "ferrule." If the ferrule doesn't come off easily, use the butane torch to heat it a bit, and then it should come right off.
How to make a golf club with masking tape?
Step 1. Completely cover the head of the club with masking tape to prevent the head from being scratched during the process. Now, place the club in the vise, so that the middle of the shaft is the part being held in the vise. Make sure the club is held securely.
Can you replace a golf club shaft instead of replacing the entire club?
By Tami Fisher. Replacing a golf shaft instead of replacing the entire club can save money. Once in a while, something happens to cause a golf club shaft to splinter or even break. When this happens, the old shaft must be removed and a new one installed in its place.
When to remove head from shaft?
You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose. By doing so, this will limit the possibility of heat penetrating into the shaft and causing it to break down.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
How to protect a carbon head?
If this is the case, go to you local welding supply center and get a bottle of a product called Cool Gel. This is very cool stuff! Just spray it on the carbon surface only and it will protect it from any wayward heat like an accidental pass with the torch. When you are done, you can just wipe the head with a wet paper towel or rag to remove the gel.
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
