- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How do you remove a golf shaft from the head?
Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly. Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel.
How do you remove a ferrule from a golf club?
Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it. Place the club in a vise to position it for shaft removal. The club should lie horizontally. Make sure the vise grips the shaft securely to prevent it from slipping out. Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel.
How do you remove a broken hosel from a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft. Lee Elder broke down racial barriers throughout his career and paved the way for others.
What is the hosel on a golf shaft?
The hosel is the area at the base of the clubhead where the shaft is inserted. Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
How do you get the shaft out of the hosel?
You can try to soak the hosel overnight or squirt some WD-40 to penetrate between the shaft and hosel to loosen the shaft, then retry the process. In the event you still cannot remove the stubborn broken piece of shaft, then it might be advisable to drill the shaft out of the hosel.
How do you remove a steel shaft from a hosel?
0:383:38How to Remove a Steel Shaft Broken Off at the Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use either number four which it fits in fairly deep. Or a number five screw extractor whichMoreYou can use either number four which it fits in fairly deep. Or a number five screw extractor which will go in about a half an inch.
How do you remove graphite shaft from hosel?
1:186:40pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipApplication of the heat. Now can you use a propane torch and the big monster. Yeah you canMoreApplication of the heat. Now can you use a propane torch and the big monster. Yeah you can particularly if you're using steel on steel I don't see anything wrong with it it's just a much bigger.
How do you remove a shaft from a golf club?
1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.
How do you remove a golf ferrule?
0:223:50How to Remove Ferrule from Steel Shaft Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become aMoreGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become a bit more smooth-looking kind of like. You know it's getting warm honestly. Does not take. Much.
How do you replace a hosel?
3:024:36SHAFT INSTALL In Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext apply epoxy to the tip of the shaft. Be sure to get good coverage over the tip of the shaft.MoreNext apply epoxy to the tip of the shaft. Be sure to get good coverage over the tip of the shaft. Install the shaft into the hosel bore slowly rotating or twisting the shaft as it goes into the hosel.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
How do I make a graphite shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do you pull a shaft adapter?
0:139:32How to Remove Golf Shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.
How do you Reshaft a golf club at home?
2:2522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heatMoreUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you Reshaft a golf club at home?
How do you change the shaft on a golf club?
0:335:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so we lay it in in this little groove right here. Which is going to slide back and forth andMoreTool so we lay it in in this little groove right here. Which is going to slide back and forth and put pressure and pull on the head. As the shaft is heated. Then we tighten the shaft.Golf Equipment : How to Change a Golf Shaft - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you change the shaft on a golf club?
How do you remove a driver shaft?
As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force. The shaft could break off inside the hosel. Work the head free carefully and gradually until it comes off.How to Remove a Golf Shaft From the Head | Golfweekhttps://golftips.golfweek.usatoday.com › remove-golf-sha...https://golftips.golfweek.usatoday.com › remove-golf-sha...Search for: How do you remove a driver shaft?
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
How to melt glue on a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
What to do if shaft piece fails to come out?
However, if the shaft piece fails to come out or slip, remove the easyout and repeat the last step. (Note: Never heat the hosel with the easyout inserted into the hosel as this can change the tempering of the easyout and possibly cause it to break off within the hosel) Once the broken piece has been successfully removed from the hosel, ...
What size drill bit should I use for a tapered hosel?
Because there is the potential that the hosel is tapered, it is suggested that you start out with an undersized drill bit (T-size or smaller). This will help to take a little bit out at a time as well as preserve the tapered hosel.
How to break epoxy bond?
Once completely cleared out, heat the hosel with a propane torch to break the epoxy bond.
How long does it take to heat a hosel?
Once completely cleared out, heat the hosel with a propane torch to break the epoxy bond. This may require 30 seconds or more of heat depending upon how old the club is.
Can you remove broken iron shaft?
In the event you still cannot remove the stubborn broken piece of shaft, then it might be advisable to drill the shaft out of the hosel. On many older irons, the hosels are tapered. It is difficult to tell this ahead of time as some heads that may be normally come equipped with a taper tip shaft could have been reshafted ...
How to clean epoxy from hosel?
Clean out any remaining epoxy in the hosel. Begin using a file and scrape away the residue, then apply a solvent to a small rag and wipe down the interior of the hosel. You may want to push the rag in with the tip of a screwdriver or similar tool.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
