Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it. Place the club in a vise to position it for shaft removal. The club should lie horizontally. Make sure the vise grips the shaft securely to prevent it from slipping out. Expose the length of the head and about 8 inches of shaft.
How do you remove a ferrule from a golf club?
Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it. Place the club in a vise to position it for shaft removal. The club should lie horizontally. Make sure the vise grips the shaft securely to prevent it from slipping out. Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel.
How to remove a head from a golf shaft?
However, if you do heat the club with it in the shaft puller, make sure to heat the rear of the hosel. If you do discolor the head, at least it will be on the back side that it least likely to be seen by the golfer when the club is at address. You are now ready to apply heat to the head for the purpose of removing the head from the shaft.
How to remove rust from iron shafts?
How to Remove Rust From Iron Shafts. 1 Step 1. Dampen a rag and rub the club shaft anywhere that rust has formed. The rag will remove loose, flaked rust to help you see how much rust is ... 2 Step 2. 3 Step 3. 4 From the Web.
How to remove a graphite shaft?
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
How do you remove shafts from an iron?
0:437:18Removing an iron shaft by hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you guys have a set of clubs that are out there steel shafted irons and you're just kind ofMoreSo if you guys have a set of clubs that are out there steel shafted irons and you're just kind of interested in tinking around how do i take them apart.
How do you remove a golf club shaft?
1:145:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp once you get the ferrule off you're going to need a few minutes here up you can use basically aMoreUp once you get the ferrule off you're going to need a few minutes here up you can use basically a gas gun which I'll use a lot of times if I'm removing a steel shaft.
How do you remove and replace a golf club shaft?
0:335:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so we lay it in in this little groove right here. Which is going to slide back and forth andMoreTool so we lay it in in this little groove right here. Which is going to slide back and forth and put pressure and pull on the head. As the shaft is heated. Then we tighten the shaft.
How do you remove iron head from graphite shaft?
0:344:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How do you change an iron shaft?
2:4622:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How do I change a golf club shaft?
0:5910:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actualMoreThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actual end of the golf club or the iron. Before you actually put the new shaft in you'll need a ferrule.
Is it easy to change golf shafts?
Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How much does it cost to re shaft a golf club?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
How do you make a golf shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do you remove a golf iron head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
Can you pull a graphite shaft without a shaft puller?
Well, the general process for pulling a graphite shaft is just about the same, but there are a few key differences. You need to take more care and HAVE to use a shaft puller. Otherwise, your new fancy and expensive exotic shaft could be at serious risk for major damage.
How do you remove graphite shaft without a shaft puller?
3:205:40How to Remove a Golf Shaft | DIY project Graphite Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipDefinitely use a um a rubber hammer.MoreDefinitely use a um a rubber hammer.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
How do I remove a golf shaft adapter?
0:139:32How to Remove Golf Shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you make a golf shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How to get glue out of a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue. As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
How to get rid of loose glue?
Twist it to remove loose glue. A small amount of mineral spirits will help clean out the area.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How to catch a club head off a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
Who is Denise Sullivan?
Denise Sullivan has been writing professionally for more than five years after a long career in business. She has been published on Yahoo! Voices and other publications. Her areas of expertise are business, law, gaming, home renovations, gardening, sports and exercise.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
What to do before you heat a propane tank?
Rule #4 – Before you heat, take a peek. Before grabbing the propane tank, take of peek of the finish because this will tell you what type of heat source to use. If the hosel is a satin or high polish finish, you should have no problem using a propane (or butane) torch or heat gun.
How to protect a carbon head?
If this is the case, go to you local welding supply center and get a bottle of a product called Cool Gel. This is very cool stuff! Just spray it on the carbon surface only and it will protect it from any wayward heat like an accidental pass with the torch. When you are done, you can just wipe the head with a wet paper towel or rag to remove the gel.
How to remove rust from golf club shaft?
Step 1. Dampen a rag and rub the club shaft anywhere that rust has formed. The rag will remove loose, flaked rust to help you see how much rust is sticking to the shaft.
What does it mean when a golf club shaft rusts?
When a golf club's iron shaft develops rust, this issue doesn't mean the club is no longer worth keeping. It does mean, however, that the problem requires your immediate attention. Because rust spreads over time, address the situation quickly to restore the club to its original appearance. If your clubs are rusting frequently, examine how you use ...
Who is William McCoy?
Toronto-based journalist William McCoy has been writing since 1997, specializing in topics such as sports, nutrition and health. He serves as the Studio's sports and recreation section expert. McCoy is a journalism graduate of Ryerson University.
