Golf-FAQ.com

how to remove graphite golf shafts

by Mr. Nathan Steuber PhD Published 2 years ago Updated 2 years ago
image

  • To remove a graphite golf shaft, first determine the size of the hole that needs to be drilled. ...
  • Next, use a drill bit to create the required hole in the shaft. ...
  • Finally, insert a screwdriver into the end of the drill bit and twist it until it comes out of the other side of the hole. ...
  • After tightening up the screwdriver, carefully remove the drill bit from around the hole in your shaft.

Full Answer

How do you replace a golf club shaft?

How To Re-Shaft Your Steel Golf Clubs

  1. Carefully clamp the shaft into a vise using a Shaft Vise Clamp. ...
  2. When removing steel shafts from clubheads, use a torch to heat the hosel. ...
  3. After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head. ...
  4. Using a wire brush remove excess epoxy from the inside of the hosel.

More items...

How to remove a golf shaft without a puller?

How to Remove a Golf Shaft From the Head

  1. Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
  2. Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
  3. Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
  4. Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...

How do I clean up golf club shafts?

Prevention is Better Than Cure

  • Wipe your clubs down with cotton after every round
  • Wipe your clubs with a multipurpose lubricant in every few months
  • Never store them in a humid location i.e. garage, corner of a storeroom.
  • Closely monitor the clubs once a month.
  • Spray rust remover on metal club heads and shafts. ...
  • Dry out properly before storing your clubs if they get wet.

Can you change a shaft from graphite to steel?

Steel iron shafts have been the standard for decades, but that doesn't mean they should be the standard for you. Unless you're a pro, you should take a serious look at switching out to graphite.

image

How do you remove a graphite golf club shaft?

0:344:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.

How do you remove graphite shaft without a puller?

0:353:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.

How do you remove graphite shaft at home?

0:556:40pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steelMoreNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steel on steel I don't see anything wrong with it it's just a much bigger. Application of the heat.

How do you remove a graphite shaft adapter?

0:119:32How to Remove Golf Shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.

Can you reuse graphite golf shaft?

Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely. The only way a graphite shaft will become unusable aside from some freak accidents is by human error in part of the build or an out of control temper on the course.

How do you remove golf club shafts?

1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.

How do you replace graphite steel shafts?

0:157:38How to Install Graphite Golf Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce completed set the head aside a few minutes to dry acetone evaporates very quickly and the headMoreOnce completed set the head aside a few minutes to dry acetone evaporates very quickly and the head should be ready for assembly within 5. Minutes. Once the shaft is selected for assembly.

How do you remove graphite shaft from fairway woods?

One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.

How do you remove epoxy from graphite shafts?

Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.

How do you remove a ferrule from a graphite shaft?

3:599:36Club repair / saving original ferrules! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll I really do is is just twist a little a little at a time until.MoreAll I really do is is just twist a little a little at a time until.

How do you remove adapter sleeves?

2:333:57How To Remove Golf Shaft Adapter Sleeve - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt as quickly as possible so that the glue. Doesn't cool off and harden. Again sweet and looky thereMoreIt as quickly as possible so that the glue. Doesn't cool off and harden. Again sweet and looky there pulled the shaft right off. So if you need to remove the hosel. Save it or the shaft.

How do you make a golf shaft puller?

0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.

Series Navigation

It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.

Removing an Adapter from a Wood or Driver

The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.

Series Navigation

Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.

Can you pull a pro launch shaft by hand?

I have pulled a few by hand, never anything high end so if it didn't work no biggie. I did mess up the tip of a Pro Launch shaft, just trimmed it and used it in a 5 wood. Did another that was a mess, had to drill it out and throw the shaft away, but I have had several others where I had no issues. It's risky, but it can be done.

Can you pull graphite shafts without a puller?

Pulling a graphite shaft without a shaft puller is almost a guaranteed way to ruin a shaft. You might get lucky and not damage it, but not something I would risk. If someone said here is a shaft to use and by the way, I pulled it by hand, I would pass on it.

How to remove tape from golf club?

It should take approximately 10 minutes to heat the shaft. Focus the heat gun on the grip area of the shaft where the tape is located .

What happens if your golf grips are worn out?

If your grips are worn out, then your scores will begin to suffer on the course due to the loss of control of your golf shots. Over the life of your clubs, you will need to replace the grips.

How to tape a grip?

Apply double-sided tape to the length of the grips by wrapping the tape around the shaft.

Can you remove grip tape from graphite shafts?

If you choose to do the grip replacement yourself, a common problem that arises is removing the grip tape from graphite shafts during the replacement process. Unlike steel shafted clubs, graphite shafts can be damaged much easier during the tape removal process and require special attention.

What bit to use for a 0.350 hosel?

For a 0.350” hosel use an 8.9mm bit and for a 0.370” hosel a 9.4mm bit. To aid in the process, you can also use a drill press with some sort of clubhead fixture to securely hold the hosel. If you do drill through the hosel stop and push it into the head, it is extremely difficult if not impossible to remove it in the hollow chamber.

Can you drill a broken shaft?

Don’t try to drill the broken piece of shaft all out at once unless you know absolutely for sure what the insertion depth of the head is. Remember, manufacturers do not publish this information.

Support TST Affiliates

Direct links for Mevo, Mevo+, and Pro Package. Save 10% on Mevo with coupon code "IACAS" as well.

Posts

Day 60: 2/23/2022 I got some nice work in on my priority piece. I snuck in a chipping ladder too.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9