Push on the base of the hosel with a pry bar to release the head from the shaft. Catch the head as it falls off the end of the shaft. Allow the club head to cool off before installing the new shaft.
How to remove a golf shaft without a puller?
How to Remove a Golf Shaft From the Head
- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How do I clean up golf club shafts?
Step 1: Put some white vinegar in a bucket so that it can cover the head of the club. Then splash the white vinegar over the rest of your club shaft using your hand. You can do this using a cloth though. Caution: Do it outside of your room, otherwise it will stink like Vinegar.
Can you change a shaft from graphite to steel?
The steel shafts are replaceable and graphite can be replaced with, meaning there is no heavier weight to the clubs. However, the grip may need to be changed, and you will probably have to use a new heat treatment. It requires a bit of effort, but it can be done.
How to extract graphite or steel golf shafts?
Who Should Play Steel Shafts?
- Strong golfers and athletes
- Players with lots of club head speed
- Better players than want more feel and feedback in their swing
- The golfers that like to work the ball left and right
- Players that want to control the ball flight and launch
- Those that worry more about precision and accuracy than distance
How do you remove a driver head from the shaft?
As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force. The shaft could break off inside the hosel. Work the head free carefully and gradually until it comes off.
How do you remove graphite shaft from hosel?
0:515:54How to Remove a Graphite Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo using a heat gun on high. I'm gonna heat the just the Ferro part and then cut it off with a knifeMoreSo using a heat gun on high. I'm gonna heat the just the Ferro part and then cut it off with a knife. It's ready to cut off because you'll kind of see it start to melt.
Can you pull a graphite shaft without a shaft puller?
Well, the general process for pulling a graphite shaft is just about the same, but there are a few key differences. You need to take more care and HAVE to use a shaft puller. Otherwise, your new fancy and expensive exotic shaft could be at serious risk for major damage.
How do you remove a golf iron head from the shaft?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do I make a graphite shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
Can you reuse graphite golf shaft?
Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely. The only way a graphite shaft will become unusable aside from some freak accidents is by human error in part of the build or an out of control temper on the course.
How do I remove a shaft adapter without a puller?
1:594:14Simple Taylor Made shaft adapter removal 30 sec without shaft pullerYouTubeStart of suggested clipEnd of suggested clipAll right take the head on see that moves really easy and so you just keep kind of twisting. AndMoreAll right take the head on see that moves really easy and so you just keep kind of twisting. And pulling keep the head locked in and eventually it will come all the way. Off.
How do you replace a graphite shaft on a golf club?
0:157:38How to Install Graphite Golf Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt is recommended the house will be cleaned using cotton swabs and acetone. Simply dip one or two ofMoreIt is recommended the house will be cleaned using cotton swabs and acetone. Simply dip one or two of the cotton swabs into acetone and swab out the inside of the club head hosel.
How do you remove a ferrule from a graphite shaft?
0:223:50How to Remove Ferrule from Steel Shaft Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become aMoreGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become a bit more smooth-looking kind of like. You know it's getting warm honestly. Does not take. Much.
How do you remove a wedge head from a shaft?
0:042:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you remove epoxy from graphite shafts?
Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.
How do you remove graphite shafts?
0:344:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How do you remove a ferrule from a graphite shaft?
0:223:50How to Remove Ferrule from Steel Shaft Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become aMoreGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become a bit more smooth-looking kind of like. You know it's getting warm honestly. Does not take. Much.
How do you replace a graphite shaft?
4:297:38How to Install Graphite Golf Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemove the head and place some epoxy inside the hosel dip the tip of the shaft into the epoxy mix.MoreRemove the head and place some epoxy inside the hosel dip the tip of the shaft into the epoxy mix. And then install into the head rotate.
How do you get a broken shaft out of the adapter?
0:403:32How to Remove a Graphite Shaft Broken Off at the Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipToo you're going to need some sort of drill bits.MoreToo you're going to need some sort of drill bits.
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
How to melt glue on a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
Who is Jim Hagerty?
Writer Bio. Jim Hagerty is a writer and journalist who began writing professionally in 1996. He has had articles published in the "Rock River Times," "Builder's Journal" and various websites. He earned a Bachelor of Science in public relations and journalism from Northern Michigan University in Marquette.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
Who is Denise Sullivan?
Denise Sullivan has been writing professionally for more than five years after a long career in business. She has been published on Yahoo! Voices and other publications. Her areas of expertise are business, law, gaming, home renovations, gardening, sports and exercise.
robert horneman
Golfworks sells a SHAFT EXTRACTOR BAR for $14.99 + s & h. Apply heat all around the hosel and the face of the club. Clamp the shaft in a vise using a VISE CLAMP $1.99 at Golfworks, apply heat then using the bar, push the head off. If you go slowly and apply heat continously while pushing the head it will come off. Don't rush!!
prestiege
i used a flaring tool once in a pinch to pull a head trying to save the shaft, head came off easy and the shaft was fine.
FATC1TY
I pulled a shaft once with a gas stove and an oven mitt.. Actually, I didn't, but not far off. I've actually pulled shafts before with no vice, no puller, and really nothing but a heat gun and a towel. Heat the hosel up, rotating the club around to get it hot everywhere, and not just a spot.. Generally I've been lucky enough to know about how much heat, and how long before I can stop heating it, put the grip between my feet, and pull up on the head with a slight twist in ONE direction.
Socrates
I really don't see how cutting the shaft out is better than pulling it using a heat gun. With the heat gun you, at minimum, have some chance of not ruining the shaft and unless you just sit there and cook the hell out of it you aren't going to ruin the head either and even if you do its purely cosmetic.
dlygrisse
I have pulled a few by hand, never anything high end so if it didn't work no biggie. I did mess up the tip of a Pro Launch shaft, just trimmed it and used it in a 5 wood. Did another that was a mess, had to drill it out and throw the shaft away, but I have had several others where I had no issues. It's risky, but it can be done.
hbear
Consider that is is VERY possible to ruin the shaft without it "appearing" like you did....
Socrates
When you guys messed up shafts.. Did they just come apart? Break off? End up all frayed like a paintbrush?
