Apply some pressure to the head while heating and continue doing so until the epoxy bond is softened. The head of the club should then come off easily. Once the head comes off, clean out the hosel area with the small drill bit, then pour a little acetone in the area to thoroughly clean it.
Full Answer
How do you remove a golf shaft from the head?
Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly. Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel.
How do you remove epoxy from a golf club head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you fix a broken golf clubhead?
Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue. As you apply heat, grab the clubhead and gently turn it to begin working it out.
How do you remove a ferrule from a golf club?
Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it. Place the club in a vise to position it for shaft removal. The club should lie horizontally. Make sure the vise grips the shaft securely to prevent it from slipping out. Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel.
How do you remove a golf iron head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you remove a wooden golf club head?
3:024:29Something. I use a wooden mallet. Here just tap it a few times and the head usually comes right offMoreSomething. I use a wooden mallet. Here just tap it a few times and the head usually comes right off every once in a while you're going to come across a club that's already been reset with epoxy.
How do you remove a club head from a steel shaft?
How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...
How do you remove a 3 wood head shaft?
0:364:28And either push or pull the head straight off that's the key. So what I'm going to demonstrate hereMoreAnd either push or pull the head straight off that's the key. So what I'm going to demonstrate here is I'm going to use my trusty propane torch now you may not be as adventurous.
How are golf club heads attached to the shaft?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
How do you replace club heads?
1:4010:45Probably start off on high but you want to move it around on actual the hostile here kind of andMoreProbably start off on high but you want to move it around on actual the hostile here kind of and spinning it around a little bit and make sure you get this superhot.
How do you replace a iron head on a golf club?
2:3122:36Pull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How do you remove a steel shaft from a hosel?
0:083:38You can use either number four which it fits in fairly deep. Or a number five screw extractor whichMoreYou can use either number four which it fits in fairly deep. Or a number five screw extractor which will go in about a half an inch.
How do you remove a steel golf shaft?
0:272:32You can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do you make a golf shaft puller?
0:296:43And put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do you remove an adjustable tip from a golf shaft?
0:119:32Once you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.
What kind of epoxy do you use on golf clubs?
Best 4 Epoxy Adhesives for Golf ClubsJ-B Weld 8281 Professional-Size Steel Reinforced Epoxy Twin Pack – 10 oz. View on Amazon. ... Brampton Epoxy Pro-Fix 20/20 Long Cure Golf Club Repair. View on Amazon. ... GolfWorks High Strength Epoxy Golf Club Head Shaft Adhesive 50 ml. View on Amazon. ... Permabond Epoxy For Golf Clubs.
How to get glue out of a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue. As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
How to get rid of loose glue?
Twist it to remove loose glue. A small amount of mineral spirits will help clean out the area.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
How to catch a club head off a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to get epoxy off of a clubhead?
Apply pressure to the clubhead, while applying heat to the hosel at the same time. Continue doing this until the epoxy bond has softened and the clubhead comes off easily.
How to make a golf club with masking tape?
Step 1. Completely cover the head of the club with masking tape to prevent the head from being scratched during the process. Now, place the club in the vise, so that the middle of the shaft is the part being held in the vise. Make sure the club is held securely.
How to get ferrule off of a car?
Take the utility knife and cut off the small plastic piece at the base of the shaft , also called the "ferrule." If the ferrule doesn't come off easily, use the butane torch to heat it a bit, and then it should come right off.
Can you replace a golf club shaft instead of replacing the entire club?
By Tami Fisher. Replacing a golf shaft instead of replacing the entire club can save money. Once in a while, something happens to cause a golf club shaft to splinter or even break. When this happens, the old shaft must be removed and a new one installed in its place.
Instructions
Clean the club. You can do this with a bucket of hot, soapy water and a soft cloth. To get the sole plate clean, use a small screwdriver to run through the grooves and remove dirt.
Tips & Warnings
Always use a fine piece of steel wool on the club head to prevent marring the surface of the club. Never rub too hard with the steel wool. Always allow the paint, varnish and stain to dry before applying a secondary coat. See manufacturer specifications for required drying times.
