How to Remove a Golf Shaft From the Head
- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How do you get rust off a golf club head?
Step 1: Things You'll Need
- Fine Steel Wool
- Hard bristle toothbrush
- Wet and Dry sandpaper (as fine as you can get it)
- White Vinegar
- Metal Polish
- A bucket
- A Dremel or similar rotary tool with a polishing bit (not necessary, rags will do)
- Plenty of elbow grease!
How to clean a golf club the right way?
How to Clean Golf Clubs
- Gather Cleaning Materials. What do you need to clean golf clubs at home? ...
- Get Sudsy. Squirt a little of the dishwashing liquid into the bottom of your plastic bucket, then add warm water to create suds.
- Place Your Irons In the Bucket. ...
- Clean Out the Grooves. ...
- Rinse Off the Clubhead. ...
- Dry the Clubhead and Shaft. ...
- Cleaning Woods. ...
How do you clean rust off of golf clubs?
Steps on how to clean rust off golf clubs
- Pour the vinegar into the bucket. The vinegar should be enough to cover the entire clubhead when dipped into the bucket. ...
- Start scrubbing. While the clubhead is dipped into the vinegar, cup your hand to splash some vinegar to the shaft. ...
- Sand the deeply rusted parts. ...
- Brush the grooves. ...
- Clean the handle. ...
- Wipe and dry. ...
- Buff it. ...
How to reshaft a golf club?
Update Your Golf Club With a New Shaft
- Steel Shafts: To remove a steel shaft from a metal wood or iron, place the shaft in a super lock tight shaft holder. Tighten the STSL in a vise. ...
- Measure the shaft tip. ...
- After the tip has been trimmed, abrade or roughen the shaft tip. ...
- Align the shaft graphics the way you want them by rotating the shaft. ...
- Position the club in the normal playing position. ...
How do you remove a steel shaft from a golf club?
0:042:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do you remove and replace a golf club shaft?
0:335:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so we lay it in in this little groove right here. Which is going to slide back and forth andMoreTool so we lay it in in this little groove right here. Which is going to slide back and forth and put pressure and pull on the head. As the shaft is heated. Then we tighten the shaft.
How do you get the shaft out of the hosel?
You can try to soak the hosel overnight or squirt some WD-40 to penetrate between the shaft and hosel to loosen the shaft, then retry the process. In the event you still cannot remove the stubborn broken piece of shaft, then it might be advisable to drill the shaft out of the hosel.
How do I remove a shaft adapter without a puller?
1:594:14Simple Taylor Made shaft adapter removal 30 sec without shaft pullerYouTubeStart of suggested clipEnd of suggested clipAll right take the head on see that moves really easy and so you just keep kind of twisting. AndMoreAll right take the head on see that moves really easy and so you just keep kind of twisting. And pulling keep the head locked in and eventually it will come all the way. Off.
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you Reshaft a golf club at home?
2:2522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heatMoreUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How do you remove a screw shaft?
Drill an appropriately sized small pilot hole through the screw head and slightly into the screw shaft. Then use a screw extractor bit (often referred to as an “easy out”) to slowly turn the screw out of its hole. If all else fails, use an appropriately sized drill bit to drill the screw out.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
How do you remove club head from graphite shaft?
0:314:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How do I change a golf club shaft?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.Build your own golf club shaft extractor - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you make a golf shaft puller?
How much does it cost to replace a golf club shaft?
Shaft Adapter Sleeves allow you to mount or change the heads on your shafts. The shaft adapter is usually used on drivers or woods but can be used on the golf club shaft of your choice.Adapter Sleeve for Driver Shaft .335 tip - Not Installed - Tour Shop Fresnohttps://www.tourshopfresno.com › golf-shaft-tips › adapte...https://www.tourshopfresno.com › golf-shaft-tips › adapte...Search for: What is a golf shaft adapter sleeve?
Can you change the shaft on irons?
0:5210:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actualMoreThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actual end of the golf club or the iron. Before you actually put the new shaft in you'll need a ferrule.How to replace a golf club shaft - Step by Step - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you change a golf club shaft?
How do you install a golf shaft?
0:5910:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actualMoreThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actual end of the golf club or the iron. Before you actually put the new shaft in you'll need a ferrule.
How to clean epoxy from hosel?
Clean out any remaining epoxy in the hosel. Begin using a file and scrape away the residue, then apply a solvent to a small rag and wipe down the interior of the hosel. You may want to push the rag in with the tip of a screwdriver or similar tool.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
Introduction
Steps to replace an old golf club shaft with a new steel shaft and replace an old grip with a new one.
Step 1 Golf Club Steel Shaft and Grip
Using propane or a torch, heat the hosel of the club to remove the steel shaft from the club head. The heat will break the epoxy bond that holds the head to the shaft.
Step 2
Use a wire brush to clean out the remains of the old epoxy from the club head.
Step 3
Use a piece of sand paper or a grinder to roughen the tip of the shaft where it connects to the hosel of the club head.
Step 4
Pour epoxy into a container and stir to mix it together. Once epoxy is mixed together, spin the shaft tip into the epoxy to prepare for insertion into the head.
Step 5
Insert the shaft into the club head. Hold the head and shaft together for approximately 30 seconds to secure.
Step 6
To replace the grip of the club, place the club on a level surface where you can cut a straight line through the grip using a razor blade or a utility knife.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
Can you discolor a golf club head?
If you do discolor the head, at least it will be on the back side that it least likely to be seen by the golfer when the club is at address. You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose.
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to prepare a club head for a new shaft?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris.
Where did Bill Herrfeldt graduate from?
Bill Herrfeldt specializes in finance, sports and the needs of retiring people, and has been published in the national edition of "Erickson Tribune," the "Washington Post" and the "Arizona Republic." He graduated from the University of Louisville.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
Introduction – DIY Golf Shaft Pulling Tricks
We previously wrote about “ How to Pull a Golf Shaft ” where we cover the basic technique for properly and safely pulling both steel and graphite golf shafts. While that technique is a great best practice, and the only foolproof (-ish) safe way to pull graphite shafts, there are a few hacks you can use for pulling steel shafts at your home.
The Stove
This is the same technique as “by hand” but you use the stove for your heat source. I’ve been in a couple of random situations where I didn’t have a propane torch or heat gun at my disposal and had to pull a steel shaft from a head. All I did was fire up a burner on the stove and use it to heat the epoxy.
In a Vise
The vise technique is one of the great at-home DIY golf shaft pulling tricks. It’s not dissimilar to the “by hand” technique, but gives you a little more leverage and keeps your hands away from the heat. For this technique, you can approach in two different ways.
Boiling Water
This is my absolute favorite DIY golf shaft pulling trick based on ingenuity alone. What’s nice about this technique is that it works well and makes saving your sweet custom ferrules feasible as long as they weren’t super epoxied on. In order to do this, fill a pot with enough water to submerge your club head in.
Conclusion
Like I said in the intro, I’m going to recommend using traditional shaft removal techniques 100% of the time. You can find that approach here . That said, there are situations that may require an alternative approach and hopefully these DIY golf shaft pulling tricks will help you out there.