- Put on protective gloves and keep them on until the procedure is complete.
- Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. ...
- Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft.
- Allow the club head to cool completely once its been liberated from the shaft.
- Roll up a small piece of sandpaper and use it to clean out any remaining epoxy residue inside the hosel joint, making it ready for the insertion of ...
How to remove a broken shaft from a club?
Golfworks sells a SHAFT EXTRACTOR BAR for $14.99 + s & h. Apply heat all around the hosel and the face of the club. Clamp the shaft in a vise using a VISE CLAMP $1.99 at Golfworks, apply heat then using the bar, push the head off. If you go slowly and apply heat continously while pushing the head it will come off. Don't rush!!
How do you remove epoxy from a golf club head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you remove the head of a broken shaft?
Apply heat all around the hosel and the face of the club. Clamp the shaft in a vise using a VISE CLAMP $1.99 at Golfworks, apply heat then using the bar, push the head off. If you go slowly and apply heat continously while pushing the head it will come off. Don't rush!! More sharing options... Without a puller your chances are next to none.
How do you remove the shaft from the hosel?
Clamp the shaft in a vise using a VISE CLAMP $1.99 at Golfworks, apply heat then using the bar, push the head off. If you go slowly and apply heat continously while pushing the head it will come off. Don't rush!! More sharing options... Without a puller your chances are next to none. Cut the shaft off and drill the remaining out of the hosel.
How do you remove golf club shafts?
1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.
How do you remove a golf shaft adapter?
0:119:32How to Remove Golf Shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.
Can you pull a graphite shaft without a shaft puller?
Well, the general process for pulling a graphite shaft is just about the same, but there are a few key differences. You need to take more care and HAVE to use a shaft puller. Otherwise, your new fancy and expensive exotic shaft could be at serious risk for major damage.
How do you remove and replace a golf club shaft?
0:335:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so we lay it in in this little groove right here. Which is going to slide back and forth andMoreTool so we lay it in in this little groove right here. Which is going to slide back and forth and put pressure and pull on the head. As the shaft is heated. Then we tighten the shaft.
How do you remove a shaft sleeve?
0:251:31Shaft Sleeve Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you'll do is you'll take a couple hammers put one on the bottom and one on the top. And you'llMoreSo you'll do is you'll take a couple hammers put one on the bottom and one on the top. And you'll just beat on the sleeve. And you'll turn it. And keep doing it until it pins it out and then loosens.
How do I change a shaft adapter?
6:4617:13How To remove / Install a Golf shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe fair or the adapter. Piece and the adapters are made out of aluminum. And aluminum transfers aMoreThe fair or the adapter. Piece and the adapters are made out of aluminum. And aluminum transfers a truckload of heat okay a bunch of heat and. So it doesn't take like you're heating up a hassel.
How do you remove a graphite shaft at home?
0:556:39pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steelMoreNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steel on steel I don't see anything wrong with it it's just a much bigger. Application of the heat.
Can you remove a golf shaft with a hair dryer?
Another alternative heat source I've had success with (literally twice) was a hair dryer. I read about golfers packing prized putters in their carry-on luggage, re-shafting at their hotel, and then removing the head with the hotel hair dryer prior to traveling home. Following that, I tried it and it worked.
How do you remove graphite golf shafts?
0:344:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How do you separate a golf club head from the shaft?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.How to Remove a Golf Club Head | Golflink.comhttps://www.golflink.com › how_1385_remove-golf-club...https://www.golflink.com › how_1385_remove-golf-club...
How much does it cost to re shaft a golf club?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.Average Cost To Reshaft Golf Clubs: With Real Exampleshttps://outofboundsgolf.com › average-cost-to-reshaft-gol...https://outofboundsgolf.com › average-cost-to-reshaft-gol...
How do you take golf clubs apart?
0:172:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow there's lots of ways to do this but in a few tools as well. I'm going to show you probably theMoreNow there's lots of ways to do this but in a few tools as well. I'm going to show you probably the easiest way and that's with the propane torch. You can also use a heat gun but it's going to takeHow To Remove A Steel Golf Shaft From A Golf Club - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watch
Can you reuse a shaft adapter?
One would be to reuse the existing adapter and the other is purchasing a new adapter sleeve and starting fresh. There are good reasons for either choice. If you do decide on using the original OEM adapter, then that will save money.
How do you remove a driver head from the shaft?
0:314:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat are commercially available but they do essentially the same thing they securely clamp the shaftMoreThat are commercially available but they do essentially the same thing they securely clamp the shaft. And either push or pull the head straight off that's the key.
What is a golf shaft adapter?
Shaft adapters make it possible to get the best fit between club and shaft and also enable very slight adjustments to the performance of the assembly that can improve your performance - and they can also make it possible to switch heads.
How do golf shaft adapters work?
Instead of the shaft directly going into the hosel of the head (like a bonded driver), you have the shaft epoxied into the shaft adapter sleeve. Those components then penetrate the head which is secured by a screw. The stop for the screw is viewable by looking at the bottom of the head.
Introduction – DIY Golf Shaft Pulling Tricks
We previously wrote about “ How to Pull a Golf Shaft ” where we cover the basic technique for properly and safely pulling both steel and graphite golf shafts. While that technique is a great best practice, and the only foolproof (-ish) safe way to pull graphite shafts, there are a few hacks you can use for pulling steel shafts at your home.
The Stove
This is the same technique as “by hand” but you use the stove for your heat source. I’ve been in a couple of random situations where I didn’t have a propane torch or heat gun at my disposal and had to pull a steel shaft from a head. All I did was fire up a burner on the stove and use it to heat the epoxy.
In a Vise
The vise technique is one of the great at-home DIY golf shaft pulling tricks. It’s not dissimilar to the “by hand” technique, but gives you a little more leverage and keeps your hands away from the heat. For this technique, you can approach in two different ways.
Boiling Water
This is my absolute favorite DIY golf shaft pulling trick based on ingenuity alone. What’s nice about this technique is that it works well and makes saving your sweet custom ferrules feasible as long as they weren’t super epoxied on. In order to do this, fill a pot with enough water to submerge your club head in.
Conclusion
Like I said in the intro, I’m going to recommend using traditional shaft removal techniques 100% of the time. You can find that approach here . That said, there are situations that may require an alternative approach and hopefully these DIY golf shaft pulling tricks will help you out there.
How to make a golf club with masking tape?
Step 1. Completely cover the head of the club with masking tape to prevent the head from being scratched during the process. Now, place the club in the vise, so that the middle of the shaft is the part being held in the vise. Make sure the club is held securely.
Can you replace a golf club shaft instead of replacing the entire club?
By Tami Fisher. Replacing a golf shaft instead of replacing the entire club can save money. Once in a while, something happens to cause a golf club shaft to splinter or even break. When this happens, the old shaft must be removed and a new one installed in its place.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
EmperorPenguin
Remember that I'm an amateur clubmaker, and when it comes to pulling old shafts I am terrible. I just use a blowtorch and there is a ton of soot, I burn off the paint and the ferrule is blued. This sounds easy to you guys, but for me I don't have a clue.
Albatross85
Graphite- get a shaft puller and apply a heat gun or a very pinpoint butane torch in the correct spot at an angle away from the head and shaft while applying constant pressure with the puller.
tareatingrat
If you're not too confident in your abilities, you can also get some gel shield paste (I got mine at Golfworks) to cover the areas you don't want to damage.
vman
This is just an example of beginners blowtorch (Napalm) over enthusiasm. Gently does it next time.
EmperorPenguin
In my lousy amateur attempt, I tried to do it with only a butane torch and nothing else. My question is how it is possible to remove the shaft without a workbench and without a shaft puller?
Nessism
In my lousy amateur attempt, I tried to do it with only a butane torch and nothing else. My question is how it is possible to remove the shaft without a workbench and without a shaft puller?
Socrates
In my lousy amateur attempt, I tried to do it with only a butane torch and nothing else. My question is how it is possible to remove the shaft without a workbench and without a shaft puller?
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
robert horneman
Golfworks sells a SHAFT EXTRACTOR BAR for $14.99 + s & h. Apply heat all around the hosel and the face of the club. Clamp the shaft in a vise using a VISE CLAMP $1.99 at Golfworks, apply heat then using the bar, push the head off. If you go slowly and apply heat continously while pushing the head it will come off. Don't rush!!
prestiege
i used a flaring tool once in a pinch to pull a head trying to save the shaft, head came off easy and the shaft was fine.
FATC1TY
I pulled a shaft once with a gas stove and an oven mitt.. Actually, I didn't, but not far off. I've actually pulled shafts before with no vice, no puller, and really nothing but a heat gun and a towel. Heat the hosel up, rotating the club around to get it hot everywhere, and not just a spot.. Generally I've been lucky enough to know about how much heat, and how long before I can stop heating it, put the grip between my feet, and pull up on the head with a slight twist in ONE direction.
Socrates
I really don't see how cutting the shaft out is better than pulling it using a heat gun. With the heat gun you, at minimum, have some chance of not ruining the shaft and unless you just sit there and cook the hell out of it you aren't going to ruin the head either and even if you do its purely cosmetic.
dlygrisse
I have pulled a few by hand, never anything high end so if it didn't work no biggie. I did mess up the tip of a Pro Launch shaft, just trimmed it and used it in a 5 wood. Did another that was a mess, had to drill it out and throw the shaft away, but I have had several others where I had no issues. It's risky, but it can be done.
hbear
Consider that is is VERY possible to ruin the shaft without it "appearing" like you did....
Socrates
When you guys messed up shafts.. Did they just come apart? Break off? End up all frayed like a paintbrush?
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to prepare a club head for a new shaft?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris.
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
