With the flat side of the clips to the outside, snap the clips into place on the 4 mounting holes on the shifter back assembly as shown in FIGURE 1-B. 2. Place the cart in the forward position and remove the stock shifter lever.
Full Answer
What to do if your Yamaha golf cart is not moving?
You can move the belt a little in its groove and do the test again. The starter bushes can also be the reason for the golf cart not moving. Check the controller if you find that your Yamaha golf cart’s solenoid is not clicking after you have installed a new set of batteries.
How to fix a Yamaha G29 golf cart pedal switch problem?
In the G29 Yamaha golf cart, the pedal switch could be the issue. You should check it thoroughly. One quick way to do this is to press the pedal right up to the floor and remove your foot in a quick motion allowing the pedal to spring back to its original position in one stroke. Sometimes, this action can sort out the issue.
Is there a custom dash assembly for a Yamaha golf cart?
This Yamaha Golf Cart Custom Dash Assembly is designed for installation on ALL YAMAHA DRIVE GOLF CARTS (YDRE/YDRA/G29) . This new dash will give your Yamaha center console a completely custom look.
How do I Reset my Electric golf cart?
On electric motors there are often reset buttons that act like mini circuit breakers. Generally, where the wires enter the unit a small little red button will be sticking out in that same vicinity. Find the button and push it back in. Test the cart. When the reset button has been pushed it, turn the cart on and gently push on the power pedal.
How do you disassemble a Yamaha golf cart?
0:538:59Yamaha Drive G29 Golf Cart - Body Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipDrive ones from 2007 up to 2016. You do have to remove the top or top supports. To be able to removeMoreDrive ones from 2007 up to 2016. You do have to remove the top or top supports. To be able to remove the front or rear body section from the cart.
How do I speed up my Yamaha electric golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you take the bumper off a Yamaha golf cart?
0:555:14Armor Bumper for Yamaha® Drive | How to Install Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's two bolts that hold the bumper on to the frame. You're going to use ten millimeter socketMoreThere's two bolts that hold the bumper on to the frame. You're going to use ten millimeter socket and remove. These. Using a 17 millimeter socket.
Where is the model number on a Yamaha golf cart?
It is likely located:Under the rear bumper on the frame; or.Under the seat where the floor board meets the motor compartment; or.Under driver side glove box.
Why is my electric golf cart so slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How fast can a 48v golf cart go?
The standard 48v golf cart will travel between 12 to 14 mph. However, if you apply modifications to the vehicle you can expect top speeds of 20 to 24mph.
How do you change shocks on a Yamaha golf cart?
0:322:02Front Shock Replacement on a Club Car Precedent Golf Cart How-ToYouTubeStart of suggested clipEnd of suggested clipBefore we jack two from the car up let's loosen all the loading us so we can get this car out. TheMoreBefore we jack two from the car up let's loosen all the loading us so we can get this car out. The first thing we'll do is go ahead and remove the bottom bolt. Okay now to remove the top bolt.
How do you change a solenoid on a Yamaha golf cart?
1:065:38Replace Solenoid in Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you start by removing the bolts that actually hold the solenoid to your golf cart wherever thatMoreSo you start by removing the bolts that actually hold the solenoid to your golf cart wherever that might be. And one of the tips i also like to mention is hold up your new solenoid.
What year is a G29 Yamaha Golf Cart?
2007In 2007 Yamaha introduced the Yamaha 'Drive' or G29 golf cart which was in production through 2016. The body was still rounded and had the tuning fork logo but the cuves and lines changed as did the seats cupholder and top. The G29A was gas and G29E was electric.
How can you tell what year a Yamaha golf cart is?
Usually found under the seat, under the driver side glove box area or on the chassis towards the rear of the golf cart. Under the bumper area usually. Once you have located this you can use the chart below to cross-reference those numbers and determine the year and model of your Yamaha Golf Cart.
What are the different models of Yamaha golf carts?
Yamaha has released three series of golf carts: the G Series, the Drive Series, and the Adventurer Series. Most collections include both gas and electric models, so keep that in mind as you search for your model year.
How can you tell what year a golf cart is?
1:272:42What Year is My Club Car? | New Golf Cart Owners: 101 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey always seem to know what you want before you call. With club car vehicles the cereal is usuallyMoreThey always seem to know what you want before you call. With club car vehicles the cereal is usually in the dashboard or glove box area or just underneath. And is sometimes on the steering.
Why is my Yamaha golf cart not moving?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid. The battery has to be checked first to see if it’s delivering the right voltage while in the idle state as well as when the pedal is pressed. There can be other reasons for the Yamaha golf cart not moving though you hear the click.
What to do if your G9 golf cart is not clicking?
If you find your G9 Yamaha golf cart not starting nor clicking, check the key components for damage. If you find the parts to in good condition, check the brushes in the starter/generator.
How to check solenoid on G9 Yamaha?
The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced. You must be careful while doing this crude test; there could be sparks when the two terminals touch.
What is a faulty controller?
The controller is one major component that may have to be replaced. A faulty controller can stall the cart and the click you hear must be from the solenoid. Test the solenoid to see if it is functioning properly. You will require a multimeter, preferably a digital one, or a DVM for this.
Where is the electric motor on a golf cart?
Located under a panel at the back of your golf cart will be the electric motor. The panel will be held in place by four or six screws. Use your screwdriver to remove these, turning them counterclockwise.
How to charge a golf cart?
Step 1. Test the wall socket where you charge your cart. Every golf cart has a built-in charger that connects to a wall socket. Take your wall socket 120-volt tester and check the actual socket that you use to charge the cart itself. Plug in your 120-volt tester and make sure the actual wall socket is good. If there is no voltage reading, your ...
What are the problems with electric golf carts?
Electric golf carts have two areas where problems usually occur, the batteries and the motor. Before you spend a lot of time and money waiting on a repairman or taking your electric golf cart to the shop, take a few seconds to troubleshoot the cart on your own.
Where are the batteries in a car charger?
If you are getting power to the charger, it's time to check the batteries. Most batteries are located under the seat, which flips up for access. Grab a hold of the back of your seat and flip it up to expose the batteries. There will be a row of batteries. Each one of these need to be checked.
What to do if your socket is not reading voltage?
If there is no voltage reading, your socket is bad and either needs to be replaced or the circuit breaker needs to be reset. You can reset the circuit breaker by flipping all the switches in your breaker box. An electrician should replace the socket.