
1. Use your pliers to disconnect the inlet hose from the stock airbox. 2. Use the 7MM ratchet to loosen and remove inlet hose.
How do I test the turbo inlet?
Testing will take place in an enclosed garage with air temperature between 70 to 78 degrees fahrenheit. The turbo inlet pipe will be attached to an OEM inlet hose and to the flowbench by means of a straight silicone coupler and flowbench adapter plate.
How is the turbo inlet pipe attached to the flowbench?
The turbo inlet pipe will be attached to an OEM inlet hose and to the flowbench by means of a straight silicone coupler and flowbench adapter plate.
What is the best source of performance data for turbocharger inlet pipe?
This project was started to evaluate the performance of a selection of Turbocharger Inlet Pipe (TIP) products. Presently the only known source of performance data for some of these products is manufacturer supplied data and user accounts that typically consist of perceived performance changes.

How do you remove a turbo inlet pipe?
3:358:03VW MK7 GTI - Turbo Inlet Pipe Install DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipLine up okay so now we remove the t30 from the turbo on the arm on the inlet pipe that'll let usMoreLine up okay so now we remove the t30 from the turbo on the arm on the inlet pipe that'll let us turn it clockwise and pull it off now remove the t30. Here at the PCB. Black. Turbo inlet pipe.
How do you remove a turbo inlet pipe 1.8 T?
1:295:37VW MK4 1.8t Forge Turbo Inlet Pipe Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipReach. There's no good angle to film this and you really don't need to watch me removing a bolt. ButMoreReach. There's no good angle to film this and you really don't need to watch me removing a bolt. But once that bolt is out you should be able to gently wiggle the turbo inlet pipe back and forth.
Is a turbo inlet pipe worth it?
1:594:31APR Turbo Inlet Pipe Review - IS IT WORTH $150? - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it I think it definitely does in the long run help the turbo breathe a little bit get a littleMoreAnd it I think it definitely does in the long run help the turbo breathe a little bit get a little bit more air efficiently.
What does a turbo inlet pipe do?
Turbo inlet hoses (TIH) are a vital component of the complete intake system in a turbocharged engine. It's the link from the intake to the turbocharger. Like other components of the intake system, an upgraded TIH seeks to increase horsepower through easing restriction.
Do you need a tune for an inlet pipe?
A: Tuning is usually not necessary for a turbo inlet hose and it is recommended to compare boost and air/fuel ratio before and after installation to make sure there are no significant changes.
What does a turbo muffler delete do?
TURBO MUFFLER DELETE DOES. The standard part is located on the outlet of the turbo compressor and is simply designed to reduce engine bay acoustics. Whilst it subdues the harmonic noises generated by the turbo, it also adds in disruptive turbulence to the airflow right where you don't want it.
What is an inlet pipe?
(ˈɪnˌlɛt paɪp ) noun. a pipe that allows a substance to enter a machine or device.
ASRman
Has anyone had any issues removing their TT Pipe or Forge Turbo Inlet Pipe from their car?
Jon R306
That sounds tricky I soaked the TT pipe O rings in engine oil for a bit before installation and covered the billet aluminium in oil and wiped off also.
ASRman
That sounds tricky I soaked the TT pipe O rings in engine oil for a bit before installation and covered the billet aluminium in oil and wiped off also.
GregR-125
Has anyone had any issues removing their TT Pipe or Forge Turbo Inlet Pipe from their car?
ASRman
Yes. Put some rubber gloves on and twist gently. It will come off and I'm sure thr effectiveness of the gloves will work as well for you as they did for me with exactly the same problem
EcosseGolfR
Has anyone had any issues removing their TT Pipe or Forge Turbo Inlet Pipe from their car?
EcosseGolfR
Apologies....just noticed you have the aluminium inlet and not the silicone hose, so just ignore what i said....I haven't seen the one that you refer too.
Penguin
Does anyone know if there’s any difference between the Turbo Technics and Revo turbo inlet pipes?
Sequence
Does anyone know if there’s any difference between the Turbo Technics and Revo turbo inlet pipes?
Dicko1989
Does anyone know if there’s any difference between the Turbo Technics and Revo turbo inlet pipes?
SpursMadDave
I take it you mean the pipe and elbow? I went with TT as got a good price and glad I did as its a good fit. Cheaper ones seem to be a bit hit and miss, not much difference between the better makes as mentioned. Sent from my VOG-L09 using Tapatalk
slider09
It seems to be one of the mods that is universally recommended and has dyno, rather than anecdotal, evidence to back up some gains.
Penguin
Is there proven evidence that these do make a difference - and I’m not allowing the butt Dyno to be the judge either
Munch
Ram air intake pipe and elbow on eBay directly from them at £119 delivered in blue, black or red. Uber easy and good fit.
1. Background
This project was started to evaluate the performance of a selection of Turbocharger Inlet Pipe (TIP) products. Presently the only known source of performance data for some of these products is manufacturer supplied data and user accounts that typically consist of perceived performance changes.
2. Purpose
This test program will consist of taking measurements of the airflow passing through each test item to enable the evaluation of relative performance among the test items and absolute performance under the test conditions. The results will show which Turbo Inlet Pipe allows the highest airflow under the test conditions.
3. Description of Equipment
The TIP is a component located along the Mk7 GTI/R engine intake and connects the airbox to the turbocharger allowing filtered air to enter the turbocharger compressor housing. All test items that are part of this program are built to function at a minimum with the IS20 or IS38 style compressor housing and stock size inlet hoses.
4. Scope of Test
Airflow testing by means of a flowbench is commonly performed at test depressions in the range of 10” to 28” of H2O. For this test program all measurements will be recorded at a depression of 28” of H2O.
5. Method of Test
Flowbench accuracy will be checked prior to collecting measurements by using a PTS calibration plate. The flowbench will be operated in a draw-through configuration. The flowbench will be operated before taking readings to perform a leak check.
6. Project Management
Availability of test items poses the most significant challenge to collecting comprehensive data. The following table summarizes candidate test items, vendor, vendor response to request, owner contribution, and links to each test case.
7. Results
The following links are to pages detailing the progress of the testing effort:
