It is better to get hold of a puller to remove the flywheel from an EZGO golf cart. Then use a plate to drill the holes to match the flywheel. Behind the flywheel, put a socket or large nut behind it. Use the flywheel bolts to pull it off. Make sure that the bind is not pulled too much on one side.
How do you remove the engine on a 2001 EZGO golf cart?
There is an easy way to remove the engine on a 2001 EZGO golf cart. Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How do I remove the flywheel of an EZGO?
The flywheel of an EZGO, be it the Workhorse or Medalist can be removed by following these steps: Find out the two dome head screws in the flywheel which seems they are there for no particular reason.
How do I remove the motor from my EZGO RXV?
EZGO RXV Motor Removal Steps 1 You have to first remove the battery wires so that the cart cannot be powered. 2 Next, the air hose should be removed from the carburetor side. 3 Use a jack to lift the cart from the rear end. 4 The drive belt should then be removed. ... 5 Use the 8mm wrench to disconnect the ‘DF’ wire from the starter. More items...
How do you remove the belt from a golf cart starter?
The easiest way is to rotate the clutch towards the cart’s rear to slip off the belt. Remove the belt and keep it aside. Use the 8mm wrench to disconnect the ‘DF’ wire from the starter. Next, use the 10mm socket to remove the ground strap from the starter/generator and remove the part from the cart.
Videos of How to Remove wheel bearing On Ez Go Golf cartbing.com › videos
Images of How To Remove Wheel Bearing on EZ Go Golf Cartbing.com › images
How do I take the hub off my EZ Go golf cart?
0:427:22EZGO rear hub replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere we go. And then the wheel just comes off and then you got the the hub exposed. Okay then whatMoreThere we go. And then the wheel just comes off and then you got the the hub exposed. Okay then what you want to do is straighten out the cotter pin. As best you can okay and then get that up and out.
How do you remove a wheel bearing without a tool?
4:5810:14How to replace a pressed in wheel bearing without a press. - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff of the ball joint made sure that this wheel speed sensor was disconnected. And i just put itMoreOff of the ball joint made sure that this wheel speed sensor was disconnected. And i just put it here so what i'm gonna have to do now is put it on two blocks.
How do I remove my EZ GO axle?
1:592:59How to Remove an E-Z-GO TXT Front and Rear Axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first step is to remove the rear pin from the brake cable once this is done remove the c-clipMoreThe first step is to remove the rear pin from the brake cable once this is done remove the c-clip and slide the brake cable from the assembly.
How do you remove a wheel bearing?
6:4016:25How to Replace a Front Wheel Bearing - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe'll put our slide hammer on it you know the slide hammer just screws right onto. This. And thenMoreWe'll put our slide hammer on it you know the slide hammer just screws right onto. This. And then all you need to do is yank this as hard as you can multiple times and it'll pop the hub right off.
What tools do I need to remove a wheel bearing?
What tools do I need to replace a wheel bearing? Needle-nose pliers, a ratchet wrench with various sized sockets, flat-head screwdriver, jack and a star wrench for loosening nuts on the wheel.
How do you press a bearing without a press?
11:4218:21PRESS IN Wheel Bearings- LIKE A PRO WITHOUT A PRESS! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith that race so because it's gonna come flush we want to make sure we use the flat side. So itMoreWith that race so because it's gonna come flush we want to make sure we use the flat side. So it doesn't close if we use this cone. Side it you won't be able to press the bearing in fully.
How do you remove an axle from a golf cart?
How do I remove the rear axle on a Club Car golf cart?Remove the rear wheel of the golf cart.Take off the brake drum from its place.Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring.Slide the axle out of its position.
How do you remove a stuck golf cart hub?
The safest way is to use a three-prong pulley puller to remove a stuck brake drum of a Yamaha golf cart. You can attach it around the perimeter of the hub and keep tighten the central bolt. After the required tightening, you can hammer carefully with a 2 to 3 pound hammer. The brake drum will soon come off.
Why do golf carts wobble?
Check whether the tire is properly seated and also check for proper wheel alignment. Sometimes if the wheel alignment is not proper, it could make the cart wobble. The lug nuts and hubs in the wheel could also cause this problem. If one of the hubs is missing or bent at an odd angle, the cart could wobble.
Can I change a wheel bearing myself?
Changing your own wheel bearings is considered an intermediate job that can be done at home, but will need some speciality mechanic tools.
How do you use a bearing removal tool?
0:105:12Press in, out and replace wheel bearing and hub with simple tools.YouTubeStart of suggested clipEnd of suggested clipHere's your hub right here. As you can see you attach that part here and then you slide it with thisMoreHere's your hub right here. As you can see you attach that part here and then you slide it with this thing stays on the car. So did this will be on a car you attach that thing with your lug nuts.
How hard is it to replace wheel bearings?
Replacing a wheel bearing that comes as an assembly with the hub and bolts to the spindle or steering knuckle is not very difficult if you have proper skills, tools and the manual. Of course, the large axle nut is very tight and can be difficult to remove.