Step 9
- Pour grip solvent into the grip, approximately 1/3 full, while holding one finger on the end of the grip to avoid it...
- Shake the grip so the inside of the grip gets all the solvent into it.
- Pour the excess solvent onto the grip tape around the shaft and have a plate or pan to avoid having a mess. Apply more...
Full Answer
How do you remove a broken shaft from a golf club?
Using propane or a torch, heat the hosel of the club to remove the steel shaft from the club head. The heat will break the epoxy bond that holds the head to the shaft. Head and shaft will be hot.
Can I refinish my golf clubs?
After years of use, golf clubs will get beat up, and in order to make them appear “new,” it is important to remove these signs of use. When I first began learning how to refinish golf clubs, it took me a while to learn how to do this. There aren’t many tutorials out there specific to the technique that is shown in the video below.
How do you remove epoxy from a golf club?
Use a wire brush to clean out the remains of the old epoxy from the club head. Use a piece of sand paper or a grinder to roughen the tip of the shaft where it connects to the hosel of the club head.
How do you replace the grip of a golf club?
To replace the grip of the club, place the club on a level surface where you can cut a straight line through the grip using a razor blade or a utility knife. Once the grip is cut, remove the grip and peel off the old tape. Apply the double-sided grip tape to the length of the grip wrapping it around the shaft .
How to remove a broken shaft from a vise?
Can you replace a golf club shaft?
About this website
Can golf irons be repaired?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself.
How do you fix a golf club iron?
0:2510:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe glue itself or the epoxy. So you can really the club head in I did have a few tools layingMoreThe glue itself or the epoxy. So you can really the club head in I did have a few tools laying around that I could allow me to do this so.
Can you reattach club head?
0:006:41HOW to FIX your GOLF CLUB if the HEAD comes off | Easy TutorialYouTubeStart of suggested clipEnd of suggested clipIf you want to just make sure you're getting the right thing basically just one side hardener. AndMoreIf you want to just make sure you're getting the right thing basically just one side hardener. And one side resin. And they mix together to form a really strong bond.
How do you fix a broken golf club?
7:549:022020 removing a broken shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd so that now that we have it so now the inside's nice and clean the outside's nice and clean andMoreAnd so that now that we have it so now the inside's nice and clean the outside's nice and clean and we just have to reshaft. It. So that's pulling a broken iron shaft with with a regular. Tool.
How do you replace a iron head on a golf club?
2:3122:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
What kind of epoxy do you use on golf clubs?
Best 4 Epoxy Adhesives for Golf ClubsJ-B Weld 8281 Professional-Size Steel Reinforced Epoxy Twin Pack – 10 oz. View on Amazon. ... Brampton Epoxy Pro-Fix 20/20 Long Cure Golf Club Repair. View on Amazon. ... GolfWorks High Strength Epoxy Golf Club Head Shaft Adhesive 50 ml. View on Amazon. ... Permabond Epoxy For Golf Clubs.
What glue is used for golf club heads?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
How do I fix my iron head?
2:0414:23LOOSE GOLF CLUB HEAD / How To Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell you can basically just skip. Ahead put a little bit of epoxy. In that space between the ferruleMoreWell you can basically just skip. Ahead put a little bit of epoxy. In that space between the ferrule. And the hosel squeeze them back together wipe it clean let it dry.
Can you play with a damaged golf club?
A player is not allowed to replace a damaged club, except when it is damaged during the round by an outside influence or natural forces, or by someone other than the player or his or her caddie.
Can you replace an iron shaft?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
Can you repair a broken club?
Under rule 4.1b(3), players are not allowed to replace clubs that they damaged during a round, though they are allowed to repair a club and continue using it thanks to the new USGA rule changes enacted in January. But if the club was damaged by “an outside influence or natural forces,” replacing it is allowed.
How do you fix a broken shaft?
1:467:16Removing a Broken Graphite Shaft 2019 -Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou've got to be able to drill it out with some drill bits. And then you've got to be able to cleanMoreYou've got to be able to drill it out with some drill bits. And then you've got to be able to clean it out so that's what we're gonna do so let's get spotted. All right just like on a shaft repair.
How to remove a broken shaft from a vise?
Step 1. Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the shaft in place. Use medium heat for graphite shafts and higher heat for steel shafts. Once the adhesive has started to melt, pull the broken shaft from the hosel, which is where the shaft meets ...
Can you replace a golf club shaft?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
What polishing compound should I use for a sisal wheel?
For polishing. Sisal wheel – This is going to do the bulk of your polishing and should be used with the black polishing compound (you can also use brown and white compounds if you are patient enough) Polishing wheels – For final touches. Use with finer polishing compounds (i.e. red, green, blue)
What is a 1/2 arbor hole?
with 1/2″ arbor holes (the cheapest and most readily available deburring and polishing wheels fit are 6″ in diameter with 1/2″ arbor holes) There is a difference between a “bench grinder” and a “bench buffer”. A bench grinder is generally used for grinding/sharpening metals, and thus, has guards on it. If you buy one of these, you may consider ...
Since 1974, The Iron Factory has been committed to superior craftsmanship and quality service
Founded by Jim Kronus, The Iron Factory began as the first and only golf club iron refinisher in the United States. Since then, we have perfected the process of repairing, rebuilding, and refinishing over a million clubs for both professional and amateur golfers.
Time
When we receive the clubs it normally takes 3-5 weeks depending on the season for all rechromes and rebuilds. Strip (only) and regrooving please allow 2 weeks. Any extra work will increase the time. Time is easily forgotten; quality is long remembered.
Shipping
Send your clubs to our listed address with a brief note of work required and include a daytime phone number.
Chroming Process
During the polishing operation weight can be lost removing nicks and dings. The amount of material added during the plating process can replace lost head weight.
Costs
All prices are per club and currently listed on our website, any special accommodations please inquire.
How to remove a broken shaft from a vise?
Step 1. Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the shaft in place. Use medium heat for graphite shafts and higher heat for steel shafts. Once the adhesive has started to melt, pull the broken shaft from the hosel, which is where the shaft meets ...
Can you replace a golf club shaft?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.