- Remove your old shafts. If they are made of steel, place one in a vise, then tighten it. ...
- Use sandpaper or a file to abrade the end of the steel shafts that will go into the hosels of your club heads. ...
- Make sure that the shafts are completely covered when you apply the epoxy to their tips. ...
- Cut the shafts to their proper length after the epoxy has hardened, which takes less than 2 hours. For steel shafts, cut them with a hacksaw. ...
- Put on the grips. Thoroughly clean the area on the shafts that will be covered by the grips before you wrap it with double-sided tape. ...
How to repair&replace a golf club shaft?
How to Repair & Replace a Golf Club Shaft. 1 Step 1. Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the ... 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5. More items
How do you replace the grip of a golf club?
To replace the grip of the club, place the club on a level surface where you can cut a straight line through the grip using a razor blade or a utility knife. Once the grip is cut, remove the grip and peel off the old tape. Apply the double-sided grip tape to the length of the grip wrapping it around the shaft .
How do you install epoxy shafts in golf clubs?
Once epoxy is mixed together, spin the shaft tip into the epoxy to prepare for insertion into the head. Insert the shaft into the club head. Hold the head and shaft together for approximately 30 seconds to secure.
How do you sand a graphite golf shaft?
Graphite shafts may have coating on the end that should be removed with a sharp blade before sanding. Apply epoxy to the inside of the hosel. Make sure the inside of the hosel is completely coated, then coat the tip of the shaft with epoxy. Slide the shaft into the hosel and turn the shaft so that the club head is properly aligned to the shaft.
Can you change the shaft on irons?
If you're thinking about changing the shafts on your golf clubs, you can either do them yourself or take them to your local golf shop.
Can you change golf shafts yourself?
Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How do I Reshaft my irons?
HOW TO RESHAFT GOLF CLUBSSteel Shafts: To remove a steel shaft from a metal wood or iron, place the shaft in a super lock tight shaft holder. ... Measure the shaft tip. ... After the tip has been trimmed, abrade or roughen the shaft tip. ... Align the shaft graphics the way you want them by rotating the shaft.More items...
How do you change a shaft on a golf club?
Scrape off the ferrule at the bottom of the club head's hosel with a utility knife. Place the club into a shaft clamp to hold it in place while you work on the head. Use a heat gun to heat up the area around the hosel to soften the epoxy glue that connects the shaft to the club head.
Should I Reshaft my irons?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
How do you change a shaft?
2:0710:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipProbably start off on high but you want to move it around on actual the hostile here kind of andMoreProbably start off on high but you want to move it around on actual the hostile here kind of and spinning it around a little bit and make sure you get this superhot.
How long does it take to Reshaft a golf club?
How long does it take to reshaft a driver? It takes 24 hours to reshaft a golf driver. The actual time depends on the epoxy used for this process. If you use an epoxy such as the Tour epoxy, you can get done with the reshafting process really fast and your driver will be ready to use in about half an hour.
How often should you Reshaft irons?
Should I reshaft irons or buy new ones? This depends on the two points of whether your golf club is fitted and new, or is old and unfitted. If your golf clubs are old and unfitted, then go for a new set of golf clubs. But if the clubs are new and fitted, then you should have them reshafted.
How do you install a golf shaft?
5:117:44SHAFT INSTALL Steel - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the ferrule is in position take the head and push the ferrule into its final position tap theMoreOnce the ferrule is in position take the head and push the ferrule into its final position tap the butt of the shaft on a hard surface to ensure the shaft is installed to the bottom of the hosel.
How do you fix a broken shaft?
1:467:16Removing a Broken Graphite Shaft 2019 -Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou've got to be able to drill it out with some drill bits. And then you've got to be able to cleanMoreYou've got to be able to drill it out with some drill bits. And then you've got to be able to clean it out so that's what we're gonna do so let's get spotted. All right just like on a shaft repair.
How hard is it to change driver shaft?
Replacing your old shaft can be a relatively painless process for you or your local repair shop. If your favorite old driver seems to have run out of quality hits, you might want to refresh it by adding a new shaft to the club.
How do you remove graphite shaft from iron?
0:344:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How to remove a shaft from a golf club?
Using propane or a torch, heat the hosel of the club to remove the steel shaft from the club head. The heat will break the epoxy bond that holds the head to the shaft.
How long to hold a golf club shaft?
Insert the shaft into the club head. Hold the head and shaft together for approximately 30 seconds to secure.
How to clean epoxy from golf club head?
Use a wire brush to clean out the remains of the old epoxy from the club head.
How to wrap a golf grip?
Apply the double-sided grip tape to the length of the grip wrapping it around the shaft . Leave 1/2 inch overhang in order to fold in the end of the shaft.
How to remove a broken shaft from a golf club?
Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the shaft in place. Use medium heat for graphite shafts and higher heat for steel shafts. Once the adhesive has started to melt, pull the broken shaft from the hosel, which is where the shaft meets the club head.
How to put a club shaft in a hosel?
Make sure the inside of the hosel is completely coated, then coat the tip of the shaft with epoxy. Slide the shaft into the hosel and turn the shaft so that the club head is properly aligned to the shaft. If there is a ferrule (small plastic piece), it should be inserted into the hosel first, then coat the interior with epoxy and slide the shaft in.
How to sand graphite shafts?
With the shaft still in the vise, use sandpaper to rough up the tip of the shaft, which will be inserted into the hosel. Graphite shafts may have coating on the end that should be removed with a sharp blade before sanding.
Can a golf club shaft be repaired?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced.
How to abrade a golf club shaft?
Use sandpaper or a file to abrade the end of the steel shafts that will go into the hosels of your club heads. However, if the shafts are made of graphite, remove the outer coating with a sanding belt before you sand them. If the shafts are a little too fat to fit into the hosels, use a wire drill bit on them until they fit snugly into them.
How to keep a golf club shaft from burning?
If they are made of steel, place one in a vise, then tighten it. If there is a plastic ferrule where the club head meets the shaft, wrap it in a wet paper towel to keep it from burning. Wearing a pair of fire-retardant gloves, heat the hosel of the club head for 30 seconds with a heat gun, then twist the shaft to remove it. ...
How to adjust grips on a golf cart?
Put on the grips. Thoroughly clean the area on the shafts that will be covered by the grips before you wrap it with double-sided tape. Cover the tape with grip solvent and carefully slide each grip down the shaft to the end. Since it takes about 10 minutes for the solvent to dry, you have plenty of time to adjust the grips with your hands.
