How do you remove the rear axle from an EZGO golf cart?
How do you remove the rear axle on a EZGO golf cart? The steps to remove the rear axle on a EZGO golf cart are:-Remove the tires by giving support to the back of the cart with help of chocks. Pull out the brackets fastening from the frame of the engine, and also take out the muffler.
How to replace a rear wheel on a golf cart?
Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring. Slide the axle out of its position. You may require a slide hammer to help you with releasing the bearing from the axle if it’s stuck on to it.
Why does the castle nut keep spinning on an EZGO golf cart?
The reason the castle nut keeps spinning on a EZGO golf cart is because the nut is too tightened on the slip axle. This means the grip on the axle has worn and the axle needs replacing. Spinning can occur due to too much pressure applied and overtightening of the nut.
How to take off axle shaft from golf cart?
The steps given below can help you to take off the axle shaft from the golf cart. Keep the chocks before the front wheels of the Club Car. Raise the back part of the cart using a floor jack. Support the cart by keeping jack stands below the axle tubes. Take off the back wheel and rim followed by the brake drum.
How do you remove an axle shaft on a EZ Go golf cart?
1:592:59How to Remove an E-Z-GO TXT Front and Rear Axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first step is to remove the rear pin from the brake cable once this is done remove the c-clipMoreThe first step is to remove the rear pin from the brake cable once this is done remove the c-clip and slide the brake cable from the assembly.
How do you remove a golf cart axle?
How do I remove the rear axle on a Club Car golf cart?Remove the rear wheel of the golf cart.Take off the brake drum from its place.Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring.Slide the axle out of its position.
How do I take the hub off my EZ Go golf cart?
0:202:18How To Quickly Replace A Stripped Golf Cart Hub - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you're going to want to do is you want to remove the cotter pin this case I used use pryMoreSo what you're going to want to do is you want to remove the cotter pin this case I used use pry some pliers. And a flat tip screwdriver. And you're going to loosen the castle.
How much does it cost to replace a rear axle?
The rear axle is usually more expensive to repair or replace. It can cost anywhere from $450 to over $1,000 for the rear axle, but most people pay between $600 – $900.
Why do golf carts wobble?
Check whether the tire is properly seated and also check for proper wheel alignment. Sometimes if the wheel alignment is not proper, it could make the cart wobble. The lug nuts and hubs in the wheel could also cause this problem. If one of the hubs is missing or bent at an odd angle, the cart could wobble.
How do you change the rear wheel bearing on a club cart golf cart?
5:0511:47How to replace a golf cart wheel axle bearing. Yamaha G29 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then your bearing will press off this way and then you press on the new one that way and this isMoreAnd then your bearing will press off this way and then you press on the new one that way and this is what it looks like. And that's it that's with the new bearing.
How do you remove hub caps from a golf cart?
0:151:13Ten Spoke Wheel Cover | How to Install Video | Madjax® Golf Cart ...YouTubeStart of suggested clipEnd of suggested clipToday we're installing mad Jack's 10-spoke will cover we're gonna use our flat-head screwdriver toMoreToday we're installing mad Jack's 10-spoke will cover we're gonna use our flat-head screwdriver to remove the existing wheel cover gently pry around the wheel cover in a few areas.
Why wont my golf cart go forward or reverse?
The problem could be with either the Run/Tow switch or Forward/Reverse switch or both. Check the switches to ensure that they aren't stuck midway. If they are, getting them released should help. However, if they show signs of wear and tear, you must get them replaced.
How do you remove a stuck golf cart hub?
The safest way is to use a three-prong pulley puller to remove a stuck brake drum of a Yamaha golf cart. You can attach it around the perimeter of the hub and keep tighten the central bolt. After the required tightening, you can hammer carefully with a 2 to 3 pound hammer. The brake drum will soon come off.
How long does it take to replace an axle?
between one and a half to three hoursReplacing a CV axle is a maintenance item that usually takes between one and a half to three hours to complete, depending on the vehicle and if other repairs are needed. A CV axle typically lasts for 70,000 to 130,000 miles, but the axles should be inspected for damage regularly.
How do you change a rear axle?
0:483:38How to Replace Rear End on Your Car (Differential) - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put one on each side so it's even then basically you on bolt everything you take the driveshaftMoreJust put one on each side so it's even then basically you on bolt everything you take the driveshaft off the back. Then you pick up the back seat.
What causes a broken axle?
Things that can break your vehicle's axle include poor maintenance; an auto accident; hitting curbs, potholes, or bumps too hard; and overloading your vehicle beyond its weight-bearing capacity. The axle is responsible for transferring the engine's power and transmission's torque to the wheels.
How do I remove the rear axle on a Club Car golf cart?
You can remove the rear axle of a Club Car golf cart by taking off the snap ring that is located behind the hub.
How to remove clamp spring from axle?
Take off the clamp spring or C-clip from the axle assembly using the internal retaining ring pliers or 90-degree C-Clip pliers.
How to remove rear axle snap ring?
You can remove the rear axle snap ring on a Club Car using a pair of 90-degree snap ring pliers and a flashlight. Take off the rear wheel from the Club Car golf cart. Remove the brake drum from its place.
What to do if your axle is stuck?
If the axle continues to be stuck to the bearings, you will need a slide hammer to tap the bearings gently a few times and loosen the axle or a bearing puller to take off the bearing.
What is a Project X HZRDUS shaft?
What is the Project X HZRDUS Black Fairway Wood shaft? Project X HZRDUS Black Fairway Wood shaft is a low spin golf shaft design. It comes with enhanced firmness over the entire length of the shaft....
Why block the front wheels of a cart?
Block the front wheels of the cart so that it doesn’t start moving unexpectedly.
How to lift rear suspension frame?
Lift the rear suspension frame using the floor jack so that the rear wheel is suspended in the air.
What is the steering wheel nut size for EZGO RXV golf cart?
What is a HZRDUS Smoke Blue RDX Wood shaft? HZRDUS Smoke Blue RDX Wood shaft is a premium quality golf shaft. Project X has created this shaft in partnership with Hexcel Technology. Are...
Why EZGO golf cart lug nuts keep coming loose?
The expansion and contraction happens because of varying temperature which loosens the nuts.
What torque should lug nuts be tightened to?
The average torque for lug nuts on a golf cart is 50 Ft/Lbs. Loose lug nuts will cause the frame to bend and cause the aluminum casing to crack.
How to fix loose lug nuts?
A lug wrench can be an effective tool to fix loose lug nuts on a golf cart.
How many holes are in an EZGO TXT bolt pattern?
EZGO TXT bolt pattern is 4×4 (4 inches by 4 inches, or 100mm apart). When measured diagonally, the wheel has 4 holes spaced out. This is the standard bolt pattern which comes with all the carting vehicles.
What size nuts are used in a golf cart?
3/4″ sized nuts are used in the axle of a EZGO golf cart. Don’t over tighten the nut as it will result in slipping of the axle and can cause damage to the complete axle set. Oiling is very important to prevent the axle from rusting and slipping.
Why does my EZGO golf cart keep spinning?
The reason the castle nut keeps spinning on a EZGO golf cart is because the nut is too tightened on the slip axle. This means the grip on the axle has worn and the axle needs replacing. Spinning can occur due to too much pressure applied and overtightening of the nut.
Special offers and product promotions
Create your FREE Amazon Business account to save up to 10% with Business-only prices and free shipping.
From the manufacturer
From humble beginnings, E-Z-GO has become the OEM world leader in transportation and a leading global manufacturer of golf cars, utility vehicles and personal transportation vehicles.
Product description
For use with E-Z-GO Golf and Utility Vehicles 2004-2010 . It is made in United states of America. A Must buy product for you with great quality.