Jack the front end of the golf cart up and place on the jack stands. Remove the front wheels and each spindle assembly using a socket or box end wrench. Fit the hole punch into the bottom of the kingpin and try to pull it out.
Full Answer
How do I change the bushings on my EZ Go golf cart?
0:132:04How to Replace Bushings for E-Z-GO Heavy Duty Leaf Springs - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut check shop easy TOCOM for vehicle specific instructions. The first step one of the txt is toMoreBut check shop easy TOCOM for vehicle specific instructions. The first step one of the txt is to remove the two bolts holding the shackle and lease rings to the vehicle with a 9/16 socket and wrench.
How do you remove king pin bushings?
7:2938:20How To Replace Kingpin Bushing And Assemble An Early Ford Front ...YouTubeStart of suggested clipEnd of suggested clipThrough. That quick so the key is to get one or two good hits to make sure you're very square. AndMoreThrough. That quick so the key is to get one or two good hits to make sure you're very square. And hitting straight down and that will kind of get it moving once it gets moved.
How do you install king pin bushings?
0:473:39Meritor FastSet No-Ream King Pin Kit Installation Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo begin the installation twist the new spiral bushings in clockwise. Start by hand at a slightMoreTo begin the installation twist the new spiral bushings in clockwise. Start by hand at a slight angle then use a t-handle tool continue installing until the bushing is below the top of the bore.
How do you ream king pin bushings?
5:2814:29Pre war Riley 9 king pin reaming - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo king pin goes through once it gets in there is a nice sliding but tight fit in that stub axle. SoMoreSo king pin goes through once it gets in there is a nice sliding but tight fit in that stub axle. So now I can push in the lower one. And ring through using the top one as a guide.
How do I know if my kingpin is worn?
Try moving the wheel left to right and top to bottom and up and down. If the wheel has any play you may have an issue likely caused by a worn kingpin. Use a dial indicator to measure, axial and lateral movement should not exceed 1/8 or . 120 in.
How long does it take to replace King Pins?
6-8 hoursA kingpin replacement generally takes 6-8 hours.
Which way do king pin bearings go?
0:472:57King Pin Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we take the king pin bearing riding up movable bearing on the bottom that's where your weightsMoreSo we take the king pin bearing riding up movable bearing on the bottom that's where your weights going to be.
Where do king pin shims go?
If excessive play is present, the spindle can be shimmed by removing the King Pin and placing one or two of the thin shims between the upper side of th axle and the upper spindle boss. The number of shims needed will be different from car to car and even side to side.
What is a king pin front end?
0:011:24King Pin vs Ball Joint Front Suspension - How to tell ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipHas an eyelet on both the bottom and the top the beam itself runs about seven inches tall.MoreHas an eyelet on both the bottom and the top the beam itself runs about seven inches tall.
What is King Pin Kit?
King pin kits are composed of king pins as centrepiece of the steering knuckle, slide bearing bushings and roller bearings. Depending on the area of application, the kits are additionally equipped with oil seals, thrust washers, o-rings, shims and lubrication nipples.
How do you use a hand reamer?
0:461:55Hand Reaming - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe best way is to pull this dreamer out at the bottom just like that. The reamer will follow theMoreThe best way is to pull this dreamer out at the bottom just like that. The reamer will follow the hoe the shank is only about mm smaller.
What is kingpin's real name?
Wilson FiskKingpin (Wilson Fisk) In Comics Powers, Abilities, & History |Marvel.
What is kingpin bearing?
Kingpin bearing is the main pivot in the steering mechanism of a car or other vehicles. Features: Excellent prevention from overrunning & backstopping. Self-Aligned. High load sustaining capacity.
What is King Pin Kit?
King pin kits are composed of king pins as centrepiece of the steering knuckle, slide bearing bushings and roller bearings. Depending on the area of application, the kits are additionally equipped with oil seals, thrust washers, o-rings, shims and lubrication nipples.
What are kingpins on a tractor?
The nipple at the front of a semi-trailer to connect to a fifth wheel coupling on a tractor unit is also known as a kingpin, which usage is analogous to the original horse-drawn wagon and traction engine steering use.
Where are kingpins located on a truck?
The kingpin, a part of the fifth wheel connection, is the pivot point between the tractor and semitrailer. The kingpin setting is the distance from the center of the fifth wheel connection to the center of the rear axle group., and affects the turning radius of the vehicle.