Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring. Slide the axle out of its position. You may require a slide hammer to help you with releasing the bearing from the axle if it’s stuck on to it.
How to remove a bearing from a golf cart axle?
You may require a slide hammer to help you with releasing the bearing from the axle if it’s stuck on to it. You can also check for a C-clip at the backside of the golf cart that keeps the axle in position. This clip is often inside the axle tube behind the drum mounting flange.
How do you remove the rear axle on a club car?
You can remove the rear axle of a Club Car golf cart by taking off the snap ring that is located behind the hub. Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring.
How to replace a rear wheel on a golf cart?
Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring. Slide the axle out of its position. You may require a slide hammer to help you with releasing the bearing from the axle if it’s stuck on to it.
What's the 1998 club car rear axle bearing location?
The axle bearing of a 1998 electric Club Car rear axle houses a retainer nut that is located inside the axle tube. This is often a C-clip and keeps the axle in position inside the tube. This C-clip or retainer nut can be accessed only using a pair of 90-degree C-clip pliers.

How do you install a rear axle bearing without a press?
9:3112:17Replace Your Rear Wheel Bearing Without a Press! - YouTubeYouTubeStart of suggested clipEnd of suggested clipI like to throw a little bit of grease on all the bolt I put back in including the threads. And theMoreI like to throw a little bit of grease on all the bolt I put back in including the threads. And the splines on the axle the threads on the axle.
How do you remove an axle shaft bearing?
3:5333:44How to replace a rear axle shaft bearing and seal on a Jeep TJ or LJ ...YouTubeStart of suggested clipEnd of suggested clipTool you got to come through the tape roller bearing cage first so get the cage out of the way allMoreTool you got to come through the tape roller bearing cage first so get the cage out of the way all these little roller bearings fall out then you have just the uh the cone.
How do you replace an inner axle bearing?
0:399:26Spring Axle Inner and Outer Bearing Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext remove the tire. And set it aside remove the dust cap by using a flat head screwdriver to pryMoreNext remove the tire. And set it aside remove the dust cap by using a flat head screwdriver to pry it out from the hub assembly rotate the hub assembly. And pry evenly around the edge.
How do you change a axle on a golf cart?
1:592:59How to Remove an E-Z-GO TXT Front and Rear Axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first step is to remove the rear pin from the brake cable once this is done remove the c-clipMoreThe first step is to remove the rear pin from the brake cable once this is done remove the c-clip and slide the brake cable from the assembly.
How do you remove a rear axle bearing?
1:4412:22How to Remove a Rear Axle Shaft Seal and Bearing with ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipCentered so and here's a race of a bearing we've already pulled and you can see how it our split oneMoreCentered so and here's a race of a bearing we've already pulled and you can see how it our split one is going to uh be up against the bearing. And allow us to pull it out.
How do you remove axle bearings without a puller?
0:393:19How to Remove Axle Bearings DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou fish it down into the bearing and then you tighten that nut up so that it's snug it might take aMoreYou fish it down into the bearing and then you tighten that nut up so that it's snug it might take a couple tries but the theory is is that if you keep it centered.