Golf-FAQ.com

how to replace the pds rocker type fnr swtch on ezgo golf cart

by Breanna Schultz Jr. Published 3 years ago Updated 2 years ago

Where is the F/R switch on a ezgp PDS?

The F/R switch on a EZGP PDS is located under the seat of the golf cart. Here are some pointers: If you want to convert it to a rocker type switch on your dash, ensure to use diodes that are at least 3 amps. Check the low voltage setting, it should be less than your cart voltage.

How do I test my EZGO forward reverse switch?

Here are a few other things that you can do to test your EZGO forward reverse switch: Check all the connections and make sure each part is getting power by using the multimeter.

Why is the FNR switch on my EZGO golf cart Hot?

A F/R switch on a EZGO golf cart is likely to get hot due to of loose or broken contacts. These broken contacts increase the resistance and heat build-up causing the FNR switch to heat up. The best solution is this case would be to have the cables replaced.

Is your f/R switch affecting your golf cart?

If you are a golf enthusiast and own a cart, then you are likely going to experience wear and tear issues that can affect your F/R switch. When the switch is in the reverse mode you get only a buzzer sound. The cart moves forward even when the switch is in the neutral position. Not getting the best speed while in the forward position.

How do I test my EZGO F&R switch?

Check all the connections and make sure each part is getting power by using the multimeter. Have your foot firmly on the brake, put in the key, and the F/R switch in the forward position. When you push the go pedal if the solenoid charges up then your EZGO F/R switch is good to go.

What does EZGO reed switch do?

Reed Switches are used to prevent cart operation with the charger plugged in. They have become increasingly expensive and they are very fragile. this component is used to eliminate the reed switch from the electrical system.

How do you remove an EZGO ignition switch?

Remove face nut with pliers. The face nut is the round piece that holds the ignition switch in place. Once the face nut is removed, the ignition switch will detach. Hang onto the lock nut for the new ignition switch if a new lock nut is no available.

How do you test a directional switch on a golf cart?

Place your foot on the car's brake, insert the key, and put the forward-reverse key in the forward position. If you see that the solenoid charges up pushing the pedal, then your forward reverse switch is working fine. As you put your Golf Cart in the forward mode, check your multimeter for full voltage.

How do I test my EZ GO micro switch?

Depress the pedal slowly. The reading should be 0.45 - 0.53 volts just as the micro-switch is activated. Depress the pedal slowly to full throttle. The reading should move smoothly to about 1.5 volts.

Where is the micro switch on a ezgo golf cart?

On EZGO gas golf carts, the accelerator micro switch is located behind the forward-reverse lever and right below the seats under the mat near the accelerator pedal.

How do you bypass the ignition switch on a golf cart?

This process includes these steps:Turn off the ignition switch to minimize your risk of electrocution. ... Locate the wires for your cart's ignition switch. ... Use wire snips to cut these wires away from their connectors. ... Touch the engines together carefully to bypass the ignition switch and send power to your engine.More items...

How do you install a light switch on a golf cart?

8:0912:58Club Car DS Headlight and Tail Light Kit How to Install Video Golf Cart ...YouTubeStart of suggested clipEnd of suggested clipWe're going to run it directly the way the factory wiring harnesses ran. So just right up underneathMoreWe're going to run it directly the way the factory wiring harnesses ran. So just right up underneath the frame. Here. Pull all your wires. Through.

How do you check the igniter on a EZ Go golf cart?

Take the voltmeter's black and red probe and place it on the –ve and +ve terminal of the coil. Take the readings. It should be between 3.7-5.2 ohms. If outside the range, the coil should be replaced.

Why won't my ezgo golf cart go forward or reverse?

A EZGO golf cart may not go forward or reverse because of a malfunctioning microswitch, solenoid, or ignition switch. Loose or corroded cable connections or a faulty controller can also cause the golf cart to not move. Malfunctioning microswitch.

Where is the reset button on a ezgo golf cart motor?

Locate the motor Remove the panel so the electric motor is visible. Electric motors usually include reset buttons that can perform similar to circuit breakers. Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.

Why will my golf cart go forward but not reverse?

The next most common problem you're likely to experience with your golf cart is a malfunctioning controller. Controllers for direction come in two varieties – forward and reverse. As a result, a cart that will go forward but not reverse may have a broken controller for the reverse that needs to be fixed or repaired.

Where is the F/R switch on a golf cart?

The F/R switch on a EZGP PDS is located under the seat of the golf cart. Here are some pointers: If you want to convert it to a rocker type switch on your dash, ensure to use diodes that are at least 3 amps. Check the low voltage setting, it should be less than your cart voltage.

What happens when you put a golf cart in reverse mode?

When the switch is in the reverse mode you get only a buzzer sound. The cart moves forward even when the switch is in the neutral position.

How to troubleshoot a cart?

Let’s go through walk you through some troubleshooting steps you can perform on your cart: The first thing you can do is to lift the seat and ensure the cables are correctly wired with no loose contacts. You may also use a multimeter to ensure there are no broken contacts.

What to do if top cover doesn't fit?

In case your top cover does not fit correctly, bend the wires to fit them in. Pro Tip: Ensure your nuts and screws are as tight as possible. If not, they are likely to vibrate when moving and this could lead to overheating and damage to your F/R switch and/or the cart as well.

Is the Ping G25 adjustable?

Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...

Do FNR switches need to be replaced?

Also, check if the board is damaged due to the heat. If yes, then the FNR switch would also need to be replaced.

Where is the ITS on an Ezgo PDS?

The ITS of an EZGO PDS is housed under the floorboard. To access the ITS, you’ll have to take off the rocker panel from the driver’s side and lift the floor mat upwards. There is a cutout on the floorboard behind the accelerator pedal. You can raise the cutout and take off the screws that keep the lid in place on the pedal box.

Where to keep positive probe on multimeter?

Keep the positive probe of the multimeter above the red wire terminal of the six-pin connector. If there is no battery voltage, the red wire between the connector and the solenoid is faulty. Keep the positive probe of the multimeter above the black wire terminal of the six-pin connector.

What happens if the solenoid doesn't go?

If there is no solenoid activation, one or both wires connected to the microswitch fail to make proper contact with the Molex connector. However, if the solenoid does click but doesn’t go, one or both the other wires connected to the ITS may have failed to make proper contact with the Molex connector.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9