how to shorten golf club length

How to Shorten the Length of a Golf Club.

• 1. Prepare the work area. Place a towel or clothes underneath your vice grip.
• 2. Place the club into the vice. Put the club into the vice such that the grip end of the club is pointing at you.
• 3. Cut off the grip. With a utility knife, carefully make a cut along the grip. Remove the grip and dispose of it in the garbage.
• 4. Remove the tape. Underneath the grip, you will find tape. Remove this by peeling it off.

Full Answer

How to measure Golf Club length for your height?

What-If Standard Sized Irons Are Not Fit for You

• Method 1. It is the method that is the most used by the golfers. ...
• Method 2. ...
• Method 3: Long Drivers of America Method (LDA) The club length is also measured by the Long Drivers of America (LDA) method. ...
• Method 4: Using Measuring Instruments. ...
• Method 5: The United States Golf Association (USGA) Method. ...

Are shorter golf clubs better?

Shorter golf clubs are better because almost everyone can use them. Shorter clubs can give you a little extra control, but the big problem about using clubs that are too small is that you’ll start to inherit bad habits and poor posture, which will ultimately hinder your performance on the course.

What is the length of a 5 iron golf club?

There are no specific industry standards for golf club length, but different manufacturers have differing lengths for clubs. A 5-iron from a particular brand is 37.75 inches, others 38 inches or even 38.5 inches long. We cannot stress enough, the importance of a golf club’s length and its effect on your performance.

How to measure Golf Club shaft length?

How to measure the length of your driver shaft:

• Keep the golf club in the playing position such that the center of the sole is in contact with the ground.
• Position a 48” golf club ruler behind the golf club making sure the ruler tip touches the ground by the heel of the club. ...
• Measure the distance from the edge of the grip cap to the heel.

Can I shorten my golf clubs myself?

If you have purchased a set of used golf clubs that are too long, you can quickly cut them down to size with a hand-held rotary tool. You can also resize your old clubs and pass them on to your children. The shaft of a golf club is narrower at the head end to generate power on the swing.

How do you cut golf clubs at home?

0:363:03Golf Tips : How to Trim Golf Club Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipGood measuring stick a marking pin will need a chop saw that we can chop with and we'll also need aMoreGood measuring stick a marking pin will need a chop saw that we can chop with and we'll also need a grinder just to trim off the burner off the end of it before the club is reesh aft.

How much does it cost to get a golf club shortened?

How much does it cost to shorten golf clubs? On average, it will cost $3-5 per club plus the cost of a new grip to shorten your clubs. If you're looking to save your old grips, you won't have to pay for new grips, but you'll have to pay a save grip fee of around $10 per club.

Can I shorten my irons?

Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.

Should I shorten my clubs?

While longer clubs can help increase speed and launch angle, shorter clubs can be easier to hit solid due to the reduction in swing arc. That's why “choking up” on the club offers a golfer more control, in general.

How long should golf clubs be for my height?

Using the ratio of every 6" of height there should be a 1" change in length then there should be a 1 ½" difference between their 5-irons. For example, recommend 36.5" for the lady and 38" for the man (or 36.75" / 38.25").

How do I know if my golf clubs are too long?

Here's how to tell if your golf clubs are too long:Completely upright posture.Improper golf swing.Odd ball flight.Feels cumbersome and unmanageable.Shaft feels weak.Consistency hitting with the toe.The measurements are wrong.

How tall should your golf clubs be?

1. Measure Your Overall Height (i.e. “static” fitting)OVERALL HEIGHTGOLF CLUB LENGTH ADJUSTMENTS5'7″ to 6'1″standard length in inches6'1″ to 6'2″plus 1/4″6'2″ to 6'4″plus 1/2″6'4″ to 6'6″plus 1″7 more rows

What to do when cutting a golf club down?

The first thing that you need to do when you’re cutting a club down is to get the old grip out of your way. In order to do that safely, you need to have plenty of space to work in and a way to hold the club steady while you’re cutting. That’s where the prepared workspace and the vice come in.

How to get adhesive off of golf club?

Heating the tape up will soften the adhesive and make this step easier. Heat the adhesive with a heat gun or a hairdryer. Peel the tape off until you have removed it all from the shaft of the club.

How to get better adhesion on a grip?

It will also emulsify the adhesive and help it to get better surface adhesion with the inside of the grip. Plug the small hole in the top of the grip with a finger and turn the grip upside down. Spray some adhesive into the inside of the grip.

How long does it take for a grip to dry?

Once you have the new grip in place, you will need to let the adhesive dry and cure. It will take approximately 6-8 hours for a full cure.

What tool to use to cut graphite shaft?

For steel shafts, a hack saw is the best option for a clean cut. For graphite clubs, you will need to use a rotary tool with a cutting wheel to get the best cut possible. Cut the desired amount from the shaft. Be careful to avoid cutting yourself with the saw or the tool.

Does trimming an inch off a golf club affect the weight?

But since you’re only trimming a little bit—it will only have a small impact on the overall performance of the club. Like we said earlier, big changes have big side effects.

Is it a good idea to cut down a set of golf clubs?

Written by Justin Adams in Beginners' Tips. Some golfers will tell you that it’s never a good idea to cut down a set of clubs. There are others who swear by it and do it all the time to make sure that their clubs are a custom-tailored fit for the golfer who will use them. There are good arguments on either side, but one thing is for sure, ...

How to shorten a golf club?

How to Shorten Golf Clubs. If you have purchased a set of used golf clubs that are too long, you can quickly cut them down to size with a hand-held rotary tool. You can also resize your old clubs and pass them on to your children. The shaft of a golf club is narrower at the head end to generate power on the swing.

Why is the shaft narrower at the head end of a golf club?

The shaft of a golf club is narrower at the head end to generate power on the swing. When shortening a golf club, you must remove the grip and cut the wide end of the shaft so the club can still flex properly.

How to cut a club shaft with a rotary tool?

Insert the cutting blade attachment into the rotary tool according to the instructions in your owner's manual. Use the rotary tool to cut the club shaft along your marked line. Smooth out the end of the shaft with a piece of fine grain sandpaper.

How to wrap a golf club grip?

Start at the end of the club and wrap grip tape around the shaft. Overlap the previous layer of tape slightly to keep it tight. Smooth out any wrinkles or bumps in the tape as you go along.

Measuring Your Golf Clubs

The easiest way to tell whether your golf clubs are too long is to measure them.

When Would You Need To Shorten Golf Clubs?

It’s evident that shortening your golf clubs is important if you intend to use them yourself and while a lot of people will have their golf clubs fitted, some opt to purchase second hand clubs.

How To Shorten Golf Clubs

If you have determined that your golf clubs need to be shortened then you’re probably eager to get the job done as quickly as possible so that you can get back onto the course.

How does shortening a golf shaft affect swing weight?

Shortening the shaft can make the golf club less flexible. If you are going to shorten a golf club, there are a few things to keep in mind. The more shaft you cut off, the lighter, more stiff, and effectively flatter the club becomes. For every 1/2 inch you remove, you will lose approximately three swingweight points.

How many swingweight points do you lose when you remove 1/2 inch?

For every 1/2 inch you remove, you will lose approximately three swingweight points. You can readjust the swingweight by adding lead tape to the head of the club. Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club.

How many inches to a standard length golf club?

Six feet, five inches-add one and a half inches to the standard length of the club. Six feet, three inches to six feet, five inches-add one inch to the standard length of the club. Six feet to six feet, three inches-add half an inch to the standard length of the club.

How to tell if a golf club is too long?

Below you’ll find common signs that indicate the clubs you’re using are too long: 1 You have to stand up almost completely straight. 2 You’re unable to move your lower body using proper swinging mechanics 3 The ball often flies off to the left and too high. 4 The club’s shaft feels very weak 5 You’re constantly hitting the ball with the toe of the golf club.

How long is a standard iron club?

Standard Club Sizes. Iron: The one iron club is a little over forty inches in length. Each iron falls half an inch with each size until you reach the nine iron which measures in at a little over thirty-six inches. Differences in irons can also occur due to shaft material.

How long is a golf driver?

On average, most golfers use a driver that’s forty-four inches in length, however, a club shaft up to forty-eight inches in allowed for competitions.

How tall should a golf iron be?

Height Recommendations for Irons. Here you’ll find the standard recommended measurements for golf clubs based on height: Six feet, six inches and taller-add two inches to the standard length of the club. Six feet, five inches-add one and a half inches to the standard length of the club.

How long is a three wood putter?

Putter: The standard length of a putter is thirty-four inches, however, the length of a putter is measured much differently than irons. It often depends on the putter’s construction.

Do beginners need to size their golf clubs?

These are questions many newbies have but don’t know the answer to. Beginners usually struggle with sizing their golf clubs correctly. Unfortunately, when it comes to clubs, size is very important. In fact, the right size of clubs can significantly improve your game, while the wrong size of clubs can negatively impact your performance, ...

How does a lengthened golf club work?

A longer distance can be achieved with a lengthened club if you have the ability to swing it with the same force and speed that you did with a shorter club . This increases the ball’s velocity upon impact, and you can hit it farther. Flex: The flex of the shaft will be altered. This happens for a few reasons.

When shortening a golf club, do you have to remove the crown?

When you shorten a golf club, you have to remove the crown, and safely disconnect the shaft from the head.

Why are golf clubs made the way they are?

The reason clubs are made the way they are is to gather momentum as you swing down. If your club is too short, you’re going to build momentum while having resistance, meaning you will push too hard against the wind and not just swing naturally. There’s not enough weight to the club.

What happens if your woods aren't longer?

If your woods didn’t have the length that they do, and they were shorter, you’d be sending your ball almost straight up and they wouldn’t close much of a distance. It’s not always about the angling of the golf club head; sometimes it’s about the length and force to make it meet the ball.

Why do you have to swoop on your golf club?

Because the club is longer, you have to swoop on your downward swing, causing the force of your wood – if you’ve hit it correctly – to be applied to the bottom of the ball and send it upwards. A wood without enough length just doesn’t cut it. You’d be sending the ball higher but with almost no distance.

What happens if you play too long in a golf club?

If the club is too long for you, then you’re spending extra time during ramp up which is the amount of time spent during your initial downswing. You want a balance between your abilities, ramp up, and momentum while cutting through the wind with as little resistance as possible.

Why did Lars start golfing?

Father of six and long-time golfer, Lars started golfing because of a summer job when he was nineteen, where he caddied for a Virginia state official. From that moment on, he fell in love with the sport, and made it a core staple in his life. Thirty-five years later, with thousands of games under his belt, he’s here to teach you the fundamentals and master techniques of golf, while recommending proper golfing gear and equipment for every step in your journey.

How to shorten a golf club shaft?

To do that, the DIY golfer will have to: 1 Remove the existing grip. 2 With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. 3 Re-install a grip on the newly shortened shaft. 4 And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. "If clubs are shortened and no weight is added back to the clubhead, the chances of the length reduction having the desired effect are somewhere between slim and none."

What is the difference between a golf shaft and a tip?

All golf shafts taper; that is, their circumference is greater at the grip end than at the tip end. That means that the grip end is the strongest part of the shaft and the tip end the weakest, which, Wishon says, leads trimming to have different effects: "Cutting more of the tip will have the effect of getting rid of some of the weaker end ...

Should the reduction in length be made from the grip end only?

"If the goal in making the clubs shorter in length is a desire to gain an improvement in accuracy, the reduction in length should be made from the grip end only ," Wishon said.