How to Shorten Golf Clubs
- Insert the golf club into a shaft clamp and tighten the clamp to keep the club from moving around while you work on the grip.
- Use a utility knife to cut the side of the existing grip. Pull off the grip and discard it. ...
- Wrap masking tape around the area of the shaft that will be cut. The tape will keep the end of the shaft from splintering as you cut.
- Insert the cutting blade attachment into the rotary tool according to the instructions in your owner's manual.
- Start at the end of the club and wrap grip tape around the shaft. Overlap the previous layer of tape slightly to keep it tight.
- Insert the pointed end of a golf tee into the hole at the end of the new grip. ...
- Place the grip over the end of the shaft and push it down before the solvent dries. ...
Full Answer
How do you shorten a golf club shaft?
With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft. And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club.
Can golf clubs be shortened?
When shortening is a good option, there are tips to help make it a smooth, efficient, and effective process. Can Golf Clubs Be Shortened? If you’ve been around the sport of golf for any length of time at all, you’ve probably heard two different kinds of stories about shortening clubs.
Why do golfers cut the shafts on their clubs?
They do this to make their clubs better fit their swing, which might mean cutting the shaft simply to change length, or to change swingweight, flex or other playing characteristics. What effect does trimming the shaft have on a golf club?
How can I extend my junior golf clubs?
You can use portions of other used steel shafts to extend the clubs or insert hardwood dowels of the appropriate size to add new length and new life onto your junior golf set. If you do decide to purchase a set of longer shafts to extend the life of the set, our recommendation is not to go any more than one inch longer.
Can you shorten golf clubs for kids?
0:013:20Is it OK to Cut Down Golf Clubs for Kids? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat they want to do is they want to take an old set of clubs that they're not using anymore. CutMoreWhat they want to do is they want to take an old set of clubs that they're not using anymore. Cut them off and give them to their kids or their wife. Usually. It's their kids.
Can golf club shafts be shortened?
With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft. And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club.
How do I shorten my golf clubs DIY?
How to Shorten Golf ClubsInsert the golf club into a shaft clamp and tighten the clamp to keep the club from moving around while you work on the grip.Use a utility knife to cut the side of the existing grip. ... Wrap masking tape around the area of the shaft that will be cut.More items...
Can golf clubs be cut shorter?
Golf clubs are often sold in a “standard” length, which is relative to each club. However, golfers differ in height and arm length, so sometimes the length of a club must be adjusted. Not only can golf clubs be lengthened for people who need it, but they can also be shortened.
Which end do you cut to shorten a golf shaft?
Discrete length shafts, where the iron shafts come shorter in lengths as you go higher up in club number, are in most cases also tapered tip (0.355"). These shafts are pre-trimmed at the tip but NOT at the butt end. The expectation is that your club-builder will trim the butt to achieve the desired final club length.
Can I cut my irons down?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
How do you cut down a golf shaft?
0:394:01How to Cut Golf Shaft DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo for the first step you have to remove your old grip. I find the easiest way to do this is toMoreSo for the first step you have to remove your old grip. I find the easiest way to do this is to literally just cut a line all the way down your club.
What can I use to cut a graphite shaft?
One solution to manually cut golf club graphite (or composite) shafts fast, safe and efficiently is the rod saw blade.
Can you adjust golf club length?
You can buy extension pieces or cut one yourself from an old shaft, using the same cutting techniques that you did for trimming a shaft from the butt end. Use sandpaper to lightly abrade the edge of the extension piece that will attach to the new shaft, then apply epoxy glue to fasten the piece to the shaft.
Should I shorten my iron shafts?
A shorter club technically should improve control and accuracy. A longer club technically should increase distance. A club that is properly fitted in terms of the length of the shaft will maximize accuracy and distance.
What happens if my irons are too long?
What Happens When Golf Clubs Are Too Long? For most golfers, having clubs that are too long will result in the most inconsistent shots. Clubs that are too long will make you stand too upright, which can cause both heel and toe shots as well as a tendency to pull the ball.
How much does it cost to shorten a driver shaft?
Generally, this fee will be about $15 to $35 depending on where and when you get the work done. Replacing a shaft on a driver is a bit more work than regripping a club. Try to have it done by a reputable person who understands club fitting.
How does shortening a golf shaft affect swing weight?
Shortening the shaft can make the golf club less flexible. If you are going to shorten a golf club, there are a few things to keep in mind. The more shaft you cut off, the lighter, more stiff, and effectively flatter the club becomes. For every 1/2 inch you remove, you will lose approximately three swingweight points.
How many swingweight points do you lose when you remove 1/2 inch?
For every 1/2 inch you remove, you will lose approximately three swingweight points. You can readjust the swingweight by adding lead tape to the head of the club. Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club.
What to do when cutting a golf club down?
The first thing that you need to do when you’re cutting a club down is to get the old grip out of your way. In order to do that safely, you need to have plenty of space to work in and a way to hold the club steady while you’re cutting. That’s where the prepared workspace and the vice come in.
How to get adhesive off of golf club?
Heating the tape up will soften the adhesive and make this step easier. Heat the adhesive with a heat gun or a hairdryer. Peel the tape off until you have removed it all from the shaft of the club.
How to get better adhesion on a grip?
It will also emulsify the adhesive and help it to get better surface adhesion with the inside of the grip. Plug the small hole in the top of the grip with a finger and turn the grip upside down. Spray some adhesive into the inside of the grip.
How long does it take for a grip to dry?
Once you have the new grip in place, you will need to let the adhesive dry and cure. It will take approximately 6-8 hours for a full cure.
How to cut yourself with a razor blade?
Put a fresh blade in your razor knife. A sharp blade cuts easier and that protects you from having to push or pull too hard, which could expose you to a higher risk of cutting yourself. A hook blade makes this step easier and safer. Slice through the grip until you have cut it from top to bottom.
What tool to use to cut graphite shaft?
For steel shafts, a hack saw is the best option for a clean cut. For graphite clubs, you will need to use a rotary tool with a cutting wheel to get the best cut possible. Cut the desired amount from the shaft. Be careful to avoid cutting yourself with the saw or the tool.
Does trimming an inch off a golf club affect the weight?
But since you’re only trimming a little bit—it will only have a small impact on the overall performance of the club. Like we said earlier, big changes have big side effects.
How long does it take to shorten a golf club?
Believe it or not, you can adjust them yourself, without going to a professional. These relatively easy steps will help you shorten a golf club in 45 minutes or less! Steps.
How to cut a golf club length?
1. Measure the desired new length of club. With the measuring tape, measure the desired length to be cut off. This distance should be taken from the top of the club. Mark the length. Use a permanent marker to mark where the cut should be made.
How to lubricate a golf grip?
Hold your finger to the tee-sized hole at the end of grip and spray the solvent into the other end. Shake this around to lubricate the inside of the grip. Put the grip onto the end of shaft. With your finger still holding all the solvent liquid inside the grip, slide the big hole onto the shaft.
How to install grip tape on a golf cart?
1. Apply grip tape to the end of the shaft. Put the new grip along the shaft to see how far down it will extend. This is how far you want the tape to go on each side.
How to get sticky glue off of a golf grip?
Spray with solvent. This will lubricate the tape so you can easily slide the grip over it. This solvent will dry up and become a sticky glue. Spray solvent into the grip. Hold your finger to the tee-sized hole at the end of grip and spray the solvent into the other end.
How to dispose of a golf club grip?
Prepare the work area. Place a towel or clothes underneath your vice grip. Place the club into the vice. Put the club into the vice such that the grip end of the club is pointing at you. Cut off the grip. With a utility knife, carefully make a cut along the grip. Remove the grip and dispose of it in the garbage.
How long does it take for a metal shaft to cool?
Wait 10-15 minutes for shaft to cool off. The metal you just cut will be hot so set it aside for several minutes and allow to cool down. Sand/dull the end of metal that was just cut. Take the sand paper and carefully smooth the end of the shaft.
How to shorten a golf club shaft?
To do that, the DIY golfer will have to: 1 Remove the existing grip. 2 With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. 3 Re-install a grip on the newly shortened shaft. 4 And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. "If clubs are shortened and no weight is added back to the clubhead, the chances of the length reduction having the desired effect are somewhere between slim and none."
What is the difference between a golf shaft and a tip?
All golf shafts taper; that is, their circumference is greater at the grip end than at the tip end. That means that the grip end is the strongest part of the shaft and the tip end the weakest, which, Wishon says, leads trimming to have different effects: "Cutting more of the tip will have the effect of getting rid of some of the weaker end ...
Should the reduction in length be made from the grip end only?
"If the goal in making the clubs shorter in length is a desire to gain an improvement in accuracy, the reduction in length should be made from the grip end only ," Wishon said.
Support TST Affiliates
Direct links for Mevo, Mevo+, and Pro Package. Save 10% on Mevo with coupon code "IACAS" as well.
Posts
Well everyone, I’ve been convinced! Too much support for me to not do it at this point. Erik, I’ll reach out on the Golf Evolution contact form and hopefully we can set something up soon. I greatly appreciate the input everyone, thank you!!
How are kids golf sets broken down?
Most kids' golf sets are broken down by age groupings, and for the beginning golfer that will work fine—in most cases. However, there are other considerations that should be taken into account.
What is a good junior golf set?
As your child gets older and more proficient, a good junior golf set will include the putter, a 3 wood and a 5, 7 and 9 (pitching wedge) irons. Do not add too many of the lower lofted clubs such as the 2 or 3 iron to your child's set because youngsters will not be able to get the ball airlifted with these lower clubs.
What is included in the Dexton Big Driver Junior Golf Set?
This Dexton Big Driver Junior Golf Set has a putter, 3 Wood, and a 5/6, 7 and 9 iron. The bag and club covers are also included.
What happens if a youth club is too long?
A youth club that is too long, too heavy, or too stiff will diminish your child's ability and potentially cause frustration. Choosing the right clubs the first time around will get the desired result: a fun and rewarding experience for both you and your child.
Can you use steel shafts on junior golf clubs?
You can use portions of other used steel shafts to extend the clubs or insert hardwood dowels of the appropriate size to add new length and new life onto your junior golf set. If you do decide to purchase a set of longer shafts to extend the life of the set, our recommendation is not to go any more than one inch longer.
Is youth golf rewarding?
Youth Golf Can Be Very Rewarding. Choosing and fitting your youngster with the appropriate clubs can be very rewarding for both you and your child. Just keep in mind that you need to choose the club length based on the child's height and ability rather than simply on their age.
Is it important to keep the weight of a golf club low?
However, the overall club weight is more important for the golf junior. For very short youngsters it is important to keep the overall weight of the club low so that they can swing more efficiently.
