How to Shorten Golf Clubs
- Insert the golf club into a shaft clamp and tighten the clamp to keep the club from moving around while you work on the grip.
- Use a utility knife to cut the side of the existing grip. Pull off the grip and discard it. ...
- Wrap masking tape around the area of the shaft that will be cut. The tape will keep the end of the shaft from splintering as you cut.
- Insert the cutting blade attachment into the rotary tool according to the instructions in your owner's manual.
- Start at the end of the club and wrap grip tape around the shaft. Overlap the previous layer of tape slightly to keep it tight.
- Insert the pointed end of a golf tee into the hole at the end of the new grip. ...
- Place the grip over the end of the shaft and push it down before the solvent dries. ...
How to shorten a golf club?
How to Shorten Golf Clubs 1 Insert the golf club into a shaft clamp and tighten the clamp to keep the club from moving around while you work on the grip. 2 Use a utility knife to cut the side of the existing grip. Pull off the grip and discard it. ... 3 Wrap masking tape around the area of the shaft that will be cut. ... More items...
How to cut a golf club to size?
Cut the club at the desired length. Using the hack saw, carefully cut the club where you marked it. Be sure keep fingers away from blade for your safety.
What happens if a junior golf club is too short?
Poor fitting clubs can lead to swing problems that can be difficult to correct in later years, and even affect the desire to play. Clubs that are too long will cause the junior to compensate with a swing that is too “flat”, and clubs that are too short will lead to a swing that is too upright.
How do I choose the right Golf Club for my child?
The best choice is a club approximately 1.5” longer than an exact fit, which allows the junior to “choke down” during initial play, gradually moving his/her hands higher on the grip as they grow over the next two seasons.
Can you shorten golf clubs for kids?
0:013:20Is it OK to Cut Down Golf Clubs for Kids? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat they want to do is they want to take an old set of clubs that they're not using anymore. CutMoreWhat they want to do is they want to take an old set of clubs that they're not using anymore. Cut them off and give them to their kids or their wife. Usually. It's their kids.
How do I make my golf clubs shorter?
How to Shorten a Golf ClubSecurely fasten the golf club in place using a vise on a workbench or similar setup, such as a golf club regripping station used at golf courses or pro shops.Cutting off the rubber golf grip using a sharp blade, such as a utility knife with a hooked blade.More items...•
How much can you shorten a golf club?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
How do you adjust length of golf clubs?
To avoid cutting the shaft or adding an attachment, purchase a new shaft at your desired length. Cut the ferrule and remove the clubhead from the old shaft as you did before trimming the tip. If you wish to keep the original grip, use an air compressor to separate it from the old shaft, then pull the grip off.
Is it bad to shorten golf clubs?
For most golfers, having clubs that are too short will be better than if they're too long, but can still result in inconsistent shots. Clubs that are too short will make you stand bent over, which can cause back pain. You'll also have the tendency to push the ball a lot.
Can I cut my irons to one length?
Every ONE Length iron has been re-engineered to match 7-iron head weight, therefore, any custom shaft (cut to 7-iron length) can work with any of the ONE Length heads.
What happens if your clubs are too long?
5 Signs Your Golf Clubs are Too Long You can't move your lower body while swinging the golf club. You keep hitting the ball with the golf club's toe. The ball tends to veer off to the left or too high when hit by the club. The golf club's shaft feels very weak when held, gripped, or swung.
Do shorter golfers need shorter clubs?
Shorter golfers are often better served with shorter clubs, while the lie angle (how the club sits on the ground) may also need tweaking. If your clubs are too long and/or upright, you'll be forced to adjust away from a swing that's natural for you.
Are shorter irons easier to hit?
Long irons are considerably harder to hit than short irons, and it is good to have a general understanding of this concept. The more prepared you are to take on these long iron shots, the better your chance for success.
What happens if I cut an inch off my driver?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
How long should your golf clubs be for your height?
Using the ratio of every 6" of height there should be a 1" change in length then there should be a 1 ½" difference between their 5-irons. For example, recommend 36.5" for the lady and 38" for the man (or 36.75" / 38.25").
What happens if golf clubs are too long?
5 Signs Your Golf Clubs are Too Long You can't move your lower body while swinging the golf club. You keep hitting the ball with the golf club's toe. The ball tends to veer off to the left or too high when hit by the club. The golf club's shaft feels very weak when held, gripped, or swung.
How do you shorten a golf shaft?
0:394:01How to Cut Golf Shaft DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo for the first step you have to remove your old grip. I find the easiest way to do this is toMoreSo for the first step you have to remove your old grip. I find the easiest way to do this is to literally just cut a line all the way down your club.
Can I cut an inch off my driver shaft?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
How to wrap a golf club grip?
Start at the end of the club and wrap grip tape around the shaft. Overlap the previous layer of tape slightly to keep it tight. Smooth out any wrinkles or bumps in the tape as you go along.
How to shorten a golf club?
How to Shorten Golf Clubs. If you have purchased a set of used golf clubs that are too long, you can quickly cut them down to size with a hand-held rotary tool. You can also resize your old clubs and pass them on to your children. The shaft of a golf club is narrower at the head end to generate power on the swing.
Why is the shaft narrower at the head end of a golf club?
The shaft of a golf club is narrower at the head end to generate power on the swing. When shortening a golf club, you must remove the grip and cut the wide end of the shaft so the club can still flex properly.
How to cut a club shaft with a rotary tool?
Insert the cutting blade attachment into the rotary tool according to the instructions in your owner's manual. Use the rotary tool to cut the club shaft along your marked line. Smooth out the end of the shaft with a piece of fine grain sandpaper.
How to lubricate a golf grip?
Hold your finger to the tee-sized hole at the end of grip and spray the solvent into the other end. Shake this around to lubricate the inside of the grip. Put the grip onto the end of shaft. With your finger still holding all the solvent liquid inside the grip, slide the big hole onto the shaft.
How to install grip tape on a golf cart?
1. Apply grip tape to the end of the shaft. Put the new grip along the shaft to see how far down it will extend. This is how far you want the tape to go on each side.
How to get sticky glue off of a golf grip?
Spray with solvent. This will lubricate the tape so you can easily slide the grip over it. This solvent will dry up and become a sticky glue. Spray solvent into the grip. Hold your finger to the tee-sized hole at the end of grip and spray the solvent into the other end.
How to dispose of a golf club grip?
Prepare the work area. Place a towel or clothes underneath your vice grip. Place the club into the vice. Put the club into the vice such that the grip end of the club is pointing at you. Cut off the grip. With a utility knife, carefully make a cut along the grip. Remove the grip and dispose of it in the garbage.
How many times has wikihow been viewed?
To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed 23,328 times.
What is wikihow wiki?
X. wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed 23,513 times.
How long does it take for a metal shaft to cool?
Wait 10-15 minutes for shaft to cool off. The metal you just cut will be hot so set it aside for several minutes and allow to cool down. Sand/dull the end of metal that was just cut. Take the sand paper and carefully smooth the end of the shaft.
How to get adhesive off of golf club?
Heating the tape up will soften the adhesive and make this step easier. Heat the adhesive with a heat gun or a hairdryer. Peel the tape off until you have removed it all from the shaft of the club.
How to get better adhesion on a grip?
It will also emulsify the adhesive and help it to get better surface adhesion with the inside of the grip. Plug the small hole in the top of the grip with a finger and turn the grip upside down. Spray some adhesive into the inside of the grip.
How long does it take for a grip to dry?
Once you have the new grip in place, you will need to let the adhesive dry and cure. It will take approximately 6-8 hours for a full cure.
What to do when cutting a golf club down?
The first thing that you need to do when you’re cutting a club down is to get the old grip out of your way. In order to do that safely, you need to have plenty of space to work in and a way to hold the club steady while you’re cutting. That’s where the prepared workspace and the vice come in.
How to cut yourself with a razor blade?
Put a fresh blade in your razor knife. A sharp blade cuts easier and that protects you from having to push or pull too hard, which could expose you to a higher risk of cutting yourself. A hook blade makes this step easier and safer. Slice through the grip until you have cut it from top to bottom.
What tool to use to cut graphite shaft?
For steel shafts, a hack saw is the best option for a clean cut. For graphite clubs, you will need to use a rotary tool with a cutting wheel to get the best cut possible. Cut the desired amount from the shaft. Be careful to avoid cutting yourself with the saw or the tool.
Is shortening a club complicated?
The actual process of shortening a club isn’t too complicated. If you know how to use a tape measure and a hack saw, you can get the job done. The trick is knowing when you can get away with it and when you’d be better off selling or trading-in a club to help with the purchase of something else. When shortening is a good option, there are tips ...
How does shortening a golf shaft affect swing weight?
Shortening the shaft can make the golf club less flexible. If you are going to shorten a golf club, there are a few things to keep in mind. The more shaft you cut off, the lighter, more stiff, and effectively flatter the club becomes. For every 1/2 inch you remove, you will lose approximately three swingweight points.
How many swingweight points do you lose when you remove 1/2 inch?
For every 1/2 inch you remove, you will lose approximately three swingweight points. You can readjust the swingweight by adding lead tape to the head of the club. Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club.
Who is Michael Joseph?
Michael Joseph is a golf industry professional in New Jersey. He has worked as a golf professional, instructor, and clubmaker. Joseph's education includes a degree in golf operations management and a certification in club-fitting from The Golf Academy of America (formally the San Diego Golf Academy).
What golf clubs do juniors use?
Advanced juniors generally use a kids golf set that includes Driver, Fairway Wood, Hybrid, 5-9 irons, Pitching Wedge, Gap Wedge, Sand Wedge and Putter. This is 12 clubs, leaving 2 more clubs that can be added depending on preference - most common are a Lob Wedge, 5-Wood, or a Second Hybrid.
What is junior golf?
Junior golf clubs sets are broadly categorized into Advanced , Intermediate and Beginner. In addition, certain Beginner sets are categorized as Budget due to their lower cost and cheaper components. Clubs are listed within each category in alphabetical order and not based on our rating or the price of the clubs.
What is intermediate junior golf club?
Intermediate/Advanced, means that the sets are high quality and have more clubs - therefore could be used for Advanced players (e.g. the Ping Prodi G sets). Of course, any intermediate or advanced junior club is also great for beginners but these do usually cost a little more than beginner kids golf clubs.
What is an advanced set?
Advanced sets are designated as such for competitive tournament players that require both high quality clubs that also have good "gapping" and therefore more clubs in the set (e.g. juniors that need clubs that have less than approx. 10 yards distance between them).
Do you cut down adult golf clubs?
Do not cut down adult clubs, they are too heavy and the shafts are generally too stiff. Young kids do not need a full set of clubs but as juniors start playing competitive golf the equipment becomes more important. A putter, wedge and three-wood or driver are great clubs to start with.
Is Taylormade Phenom the same as Rory?
The TaylorMade Phenom and Rory clubs are very similar if not identical. A visual comparison of the 2 models reveals purely cosmetic differences in the club heads although the shafts and lengths may be slightly different.
Is Taylormade Rory junior club phased out?
With the introduction of the TaylorMade Rory junior clubs the Phenom's may be phased out. As of writing this, the TaylorMade site only has the smaller (6 clubs set for ages 5-8) available for sale. See more below for a comparison of the two.
Support TST Affiliates
Direct links for Mevo, Mevo+, and Pro Package. Save 10% on Mevo with coupon code "IACAS" as well.
Posts
Well everyone, I’ve been convinced! Too much support for me to not do it at this point. Erik, I’ll reach out on the Golf Evolution contact form and hopefully we can set something up soon. I greatly appreciate the input everyone, thank you!!
