- Determine how much of the shaft’s tip you wish to trim. ...
- Place the shaft into a rubber golf club clamp, then insert the clamp into a vise. The rubber protects the graphite from damage.
- Wrap two or three layers of masking or electrical tape around the area to be cut. The tape helps prevent the shaft from splintering.
- Measure the distance that you wish to trim from the tip, then mark the distance on the tape with a pen.
- Cut carefully along the marked line with a hacksaw, insuring your blade is perpendicular to the shaft.
- Determine how much length must be trimmed from the butt end of the club. This typically depends on the type of club you're constructing.
- Tape and mark the area to be cut, as you did with the tip. However, add 1/8 inch to the cut to account for the grip cap.
- Cut the butt end the same way as you trimmed the tip.
How do you flex a graphite golf shaft?
For example, you’ll trim more off the tip to achieve a stiffer flex. Place the shaft into a rubber golf club clamp, then insert the clamp into a vise. The rubber protects the graphite from damage.
How do you cut graphite shafts?
The graphite shaft will come with trimming instructions that tell you how much to cut from the tip, depending on the amount of flex you want. For example, you’ll trim more off the tip to achieve a stiffer flex. Place the shaft into a rubber golf club clamp, then insert the clamp into a vise.
Why are graphite shafts so hard to make?
The problem with graphite shafts has always been consistency, and there’s a simple reason for this. All of the large graphite shaft manufacturers use a process known as the “roll-wrapping method” to make their graphite shafts, and the process hasn’t changed very much over the decades.
Can you re-shaft a broken graphite shaft?
First of all, it is much easier when re-shafting a driver that the customer broke or simply did not like. One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel.
How do you straighten a golf shaft?
Take your golf towel and rub the shaft vigorously up and down. The friction will heat up the shaft to a point where you can straighten a slight bend. (Yes, it actually works.)
Is it possible to straighten a bent shaft?
A bent shaft can occur as a result of damage during shipment, rigging, or operation. Shaft straightening methods, when properly applied, can sometimes be used to salvage damaged shafting. Because of the different variables involved, shaft bend correction can be as much an art as a science.
Can you bend a graphite shaft?
Yes. At normal temps at least, graphite shafts can't really get any kind of permanent bend.
Can I sand a graphite shaft?
If using a belt sander, I would recommend a graphite shaft sanding belt rather than a normal sanding belt as not to take too much material as fast. Hand sanding can be accomplished by using a 1" wide strip of medium grit sandpaper and use a shoeshine method to evenly sand around the shaft tip.
How do you straighten a bent shaft with heat?
2:2017:53Flame Straightening a bent Steel Spindle - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're going to try to salvage this by using heat straightening. So the idea of heat straighteningMoreSo we're going to try to salvage this by using heat straightening. So the idea of heat straightening is is that you find the hot spot on the shaft or you find where the bend is on the shaft.
How do you straighten a bent motor shaft?
1:002:01How to straighten a quad motor shaft using a drill - YouTubeYouTubeStart of suggested clipEnd of suggested clipUntil the end of the secondary truck reaches its maximum. And then grab the chuck and forcefullyMoreUntil the end of the secondary truck reaches its maximum. And then grab the chuck and forcefully bend it the other way to straighten it out now you have to do this a few times.
Can you hit the ball further with graphite shafts?
Graphite shafts are considerably lighter than steel shafts so they are easier to swing faster and have your golf ball go farther.
Does 1 degree lie angle make difference?
Yes it will make a difference, I play 2 degree upright and +1/2. If your hitting the ball left all the while (I am guessing your right handed) won't be to do with having the lye angle to flat.
How many degrees can you bend a golf club?
4. You can bend a club more than 2 degrees. The 2-degree limit is only recommended when changing the lofts on irons due to the potential effect such bends will have on the sole angle of the club.
How do you prepare a new graphite shaft tip?
0:595:49Golf Repair - How to Prep a Graphite Shaft Tip for Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo simply take your sandpaper. And they're not going any further than where it's been roughed upMoreSo simply take your sandpaper. And they're not going any further than where it's been roughed up before and just where your epoxy is at go ahead and just gently move back. And forth on the shaft.
What does prepping a golf shaft mean?
GOLF CLUBS INSTRUCTION SERIES. STEP 3b. Graphite. Shafts: Lightly sand shaft from tape to tip with 150 grit or finer sand paper to remove the polyurethane finish and all the paint. This operation is "prepping" the shaft and can be done by The GolfWorks (PREP).
How do you sand a shaft?
2:404:52How To Properly Abrade or Sand a Golf Shaft Tip - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain we want to sand. Just a bit higher than the top of the hose but not far enough that theMoreAgain we want to sand. Just a bit higher than the top of the hose but not far enough that the ferrule is not going to cover it up so I can either mark it with my Sharpie pen and this is a black shaft.
Can golf shafts bend?
During the downswing, the shaft bends back (called "lag"). Near impact, the shaft bends down ("droop") and then toward the target ("lead"). MacKenzie's research found that forward bend (called "kick velocity") increased more with flexible shafts than with stiffer shafts—but not for all players.
Can you reuse a graphite shaft?
Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely. The only way a graphite shaft will become unusable aside from some freak accidents is by human error in part of the build or an out of control temper on the course.
How do you remove iron head from graphite shaft?
0:344:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
Does a golf club Bend?
0:412:11Golf Equipment: How Shafts Bend - YouTubeYouTubeStart of suggested clipEnd of suggested clipCase study here to show you just the gross properties of how these shafts bent. So in here I've gotMoreCase study here to show you just the gross properties of how these shafts bent. So in here I've got a really flexible shaft. And a bend this one you can see how much it flexes.
What is the purpose of cutting a graphite shaft?
Cutting a graphite golf shaft will help you easily adjust the length and weight to suit your needs.
How to avoid saw shaft breaking?
Be sure to move the saw slowly to avoid the shaft breaking or breaking unintentionally.
Can you cut graphite shafts?
The process of cutting a graphite golf shaft is almost complete. Now you just need to double-check that the cut is exactly what you want, and you can use it.
Can you cut a golf club?
Even if you don’t spot the mistake early enough, continuing to cut can damage the entire club. A golf club is costly, and it would be a waste to throw it away because of the faulty equipment.
Do you rush to pick up a knife to cut?
After you have determined the point you want to cut, do not rush to pick up the knife to cut it. It would help if you prepared a little more to make the cutting process more convenient and safe for yourself.
Do you have to cut off long shafts?
Usually, the long shafts will have to be cut off to be more comfortable. So you should not just sit still to measure, but stand up to see if it fit s your height.
Can you cut a golf shaft with tape?
You do not need to worry too much because you will cut the golf shaft through this adhesive tape. This layer of video will help keep debris or fragments of graphite in place during the cutting process.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
How to protect a carbon head?
If this is the case, go to you local welding supply center and get a bottle of a product called Cool Gel. This is very cool stuff! Just spray it on the carbon surface only and it will protect it from any wayward heat like an accidental pass with the torch. When you are done, you can just wipe the head with a wet paper towel or rag to remove the gel.
When to remove head from shaft?
You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose. By doing so, this will limit the possibility of heat penetrating into the shaft and causing it to break down.
Introduction
Awhile back we taught you the basics of pulling a golf shaft. You can read that post here if you want. Well, the general process for pulling a graphite shaft is just about the same, but there are a few key differences. You need to take more care and HAVE to use a shaft puller.
Supplies Required
In order to pull a graphite shaft both safely and successfully, there are a few required tools. It’s important to know that if you’re pulling a graphite shaft, there is a big risk of damaging the shaft if you don’t use the proper tools. Below are my recommendations for what you will need:
How To Pull a Graphite Shaft
Making sure you use a safe technique is the most crucial portion of pulling a golf shaft. Failing to do it in a correct fashion could result in that slick $400 aftermarket shaft becoming a $400 piece of garbage. In the interest of making the process easy to follow, we’ll lay it out in bullet point fashion.
Final Thoughts – Pulling a Graphite Shaft
Once you have the correct tools, and a little knowledge, pulling a graphite shaft is pretty easy. For me, it was one of those things where I just needed to have the guts to jump in and get my hands dirty. Between a writeup like this, maybe a Youtube video or two, I was set and figured it out fairly quickly.
How NOT to Pull a Graphite Shaft
I mentioned a few times that if you don’t pull a graphite shaft properly, you’re going to have problems. If you try and twist off a head from a graphite shaft, this happens:
How to trim graphite shaft?
Step 1. Determine how much of the shaft’s tip you wish to trim. The graphite shaft will come with trimming instructions that tell you how much to cut from the tip, depending on the amount of flex you want. For example, you’ll trim more off the tip to achieve a stiffer flex.
How to protect graphite from damage?
Place the shaft into a rubber golf club clamp, then insert the clamp into a vise. The rubber protects the graphite from damage.
How to cut a line with a hacksaw?
Cut carefully along the marked line with a hacksaw, insuring your blade is perpendicular to the shaft. The Clubmakers.co.kr site suggests using a grit edge blade in your saw.
Can you add a trim back to a club shaft?
BTW, you can always add the "trim" back with a club shaft extender if it does not work out.
Can you trim a golf shaft for free?
Most clubmakers will install a shaft for free if it is purchased from them, or will have fairly modest prices (~$15-30 depending on where you go) to perform the trimming and reshafting operation you describe. I bet that if you asked them to trim your shaft they'd be willing to re-grip the shaft for free if you provided or purchased the grip!
How much lateral deviation does a shaft need to be to wobble?
Amazed by the video above? According to TPT testing and standards, a shaft would be considered as starting to wobble if it had a lateral deviation of +/- 1.5 centimeters. And as you can see, it’s unlikely that any handmade shaft could meet that standard.
Why do custom fitters do spines?
These processes don’t fix the problem; they just minimize the problem. In some cases, they make problems even worse.
Can a golf shaft be roll wrapped?
The bottom line is that a golf shaft created with the roll-wrapping method will never perform as designed. We launched TPT because that didn’t make sense to us. Of all the things that can get in the way of a golfer’s best shots, a golf shaft should not be one of them.
