- Put on protective gloves and keep them on until the procedure is complete.
- Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. ...
- Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft.
- Allow the club head to cool completely once its been liberated from the shaft.
- Roll up a small piece of sandpaper and use it to clean out any remaining epoxy residue inside the hosel joint, making it ready for the insertion of ...
How do you get rust off a golf club head?
Step 1: Things You'll Need
- Fine Steel Wool
- Hard bristle toothbrush
- Wet and Dry sandpaper (as fine as you can get it)
- White Vinegar
- Metal Polish
- A bucket
- A Dremel or similar rotary tool with a polishing bit (not necessary, rags will do)
- Plenty of elbow grease!
How to clean a golf club the right way?
How to Clean Golf Clubs
- Gather Cleaning Materials. What do you need to clean golf clubs at home? ...
- Get Sudsy. Squirt a little of the dishwashing liquid into the bottom of your plastic bucket, then add warm water to create suds.
- Place Your Irons In the Bucket. ...
- Clean Out the Grooves. ...
- Rinse Off the Clubhead. ...
- Dry the Clubhead and Shaft. ...
- Cleaning Woods. ...
How do you clean rust off of golf clubs?
Steps on how to clean rust off golf clubs
- Pour the vinegar into the bucket. The vinegar should be enough to cover the entire clubhead when dipped into the bucket. ...
- Start scrubbing. While the clubhead is dipped into the vinegar, cup your hand to splash some vinegar to the shaft. ...
- Sand the deeply rusted parts. ...
- Brush the grooves. ...
- Clean the handle. ...
- Wipe and dry. ...
- Buff it. ...
How to regrip a golf club?
- How to Regrip Golf Clubs 1. Take Off the Old Grip 2. Add Grip Tape 3. Apply Solvent Solution 4. ...
- How to Choose the Right Golf Grips to Regrip Your Golf Clubs Size Firmness Weather Conditions Texture
- Types of Golf Grips Wrapped Corded Rubber Hybrid
- Cleaning Golf Grips
- When to Regrip Golf Clubs
- Signs Your Club Grips Need to Be Replaced
- Final Thoughts
How do you remove a club head from a golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you remove a golf driver head shaft?
0:344:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How do you remove a golf iron head from the shaft?
2:217:18Removing an iron shaft by hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo how do we do this right so a simple tool burns-a-matic butane torch you can get these at lowe'sMoreSo how do we do this right so a simple tool burns-a-matic butane torch you can get these at lowe's home depot or anything like that they're like 15 bucks very handy little item for around the house.
How do you remove a wedge head from a shaft?
As you apply heat to the hosel (by keeping the heat moving around the whole area), you should periodically try and twist the head and shaft. If they don't budge, keep applying heat. Eventually you will feel the epoxy break and will be able to twist the head off.
How do I replace my driver head?
0:045:16Golf Club Repair - Removing the driver head and cleaning & preppingYouTubeStart of suggested clipEnd of suggested clipWe can take the old shaft out of the shaft extractor here pretty easy to get the old shaft out justMoreWe can take the old shaft out of the shaft extractor here pretty easy to get the old shaft out just loosen up the screws. Take the protective film off the shaft. So you don't scratch it.
How do you put a golf club head on a shaft?
3:186:14Golf Club Re-Shafting (Part 2) - YouTubeYouTubeStart of suggested clipEnd of suggested clipReapply the epoxy. There again I'm going kind of in circular motions around the tip of the shaft. I'MoreReapply the epoxy. There again I'm going kind of in circular motions around the tip of the shaft. I'll even add some to the tip of the shaft. I'm going to take my shaft.
Can you put a new driver head on an old shaft?
The only way to know if we can put your old fitted shaft into a new head it to pull the shaft, weight the head and test the new head with the old shaft. The head may be heavier or lighter, the hosel dimensions may be off which could cause a length issue.
How do you reattach a golf club head?
0:006:41HOW to FIX your GOLF CLUB if the HEAD comes off | Easy TutorialYouTubeStart of suggested clipEnd of suggested clipIf you want to just make sure you're getting the right thing basically just one side hardener. AndMoreIf you want to just make sure you're getting the right thing basically just one side hardener. And one side resin. And they mix together to form a really strong bond.
How do you remove graphite shaft without a puller?
0:353:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
How to melt glue on a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
Step 1
Put on protective gloves and keep them on until the procedure is complete.
Step 2
Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense heat evenly on all sides of the hosel and don't be alarmed if small amounts of white smoke begin to escape the hosel cavity. That is just the old epoxy melting.
Step 3
Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.
Step 4
Allow the club head to cool completely once its been liberated from the shaft.
Step 5
Roll up a small piece of sandpaper and use it to clean out any remaining epoxy residue inside the hosel joint, making it ready for the insertion of a new shaft.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to clean epoxy from hosel?
Clean out any remaining epoxy in the hosel. Begin using a file and scrape away the residue, then apply a solvent to a small rag and wipe down the interior of the hosel. You may want to push the rag in with the tip of a screwdriver or similar tool.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
Lifespan
Unfortunately, golf clubs have a life span just like a car. If a set of clubs is older than 10 years old, expect deterioration like broken shafts, heads coming off and grips unraveling. Although the lifespan can be extended by taking care of the clubs, anything beyond 10 years is likely to give problems.
Manufacturing Defects
Like all commodities, manufacturing process errors or faults do occur occasionally. Depending on the period of time and use, manufacturers are likely to accommodate claims that are within reason. They will request pictures, or inspection by their agent in the area to determine if abuse or mishandling is the cause.
Cheap Copies
The exponential growth of golf as a sport worldwide has brought about clubs being a marketable product. In China, where most of the top brands are manufactured, cheaper copy versions have sprung up, and sell at a fraction of top brand costs.
Playing Golf in the Rain
To the die-hard golfer, a bit of rain on the course is no reason to stop playing. As the saying goes; “it does not rain on the golf course”! Playing in the rain is OK, but the treatment of the clubs after the game is an important factor.
Bad Swing Mechanics
Beginners should always take a few lessons from a seasoned pro to get the basics of the golf swing right. This not only will improve your game at a faster rate but will also protect your clubs. Taking deep divots on every shot on hard turf courses will ultimately weaken the shaft and damage the clubhead.
Storing Clubs in The Car Boot
It is easy to throw the clubs into the car boot after a Saturday outing and leave them there until the following game. The temperatures in the boot will affect the longevity of the clubs. The adhesive used in securing the head to the shaft is high class, but the continuous variation in temperatures in the boot will slowly cause deterioration.
Club Abuse
Golf is a very frustrating game and will always test the player’s patience and skill level. It is one of the toughest games to master, due to the finite margins between success and failure on a shot. How often on the tee do we see an “extended” follow through with the club banged into the ground!
