Once you have the necessary tools, follow these steps to remove the governor:
- Disconnect the negative battery terminal from the cart. This will prevent any accidental sparks from occurring.
- Remove the screws that hold the governor’s cover in place. ...
- Use the wire cutters to cut the zip tie that holds the wires to the governor.
- Remove the screws that hold the governor to the battery pack.
How do you bypass the governor on an EZGO golf cart?
How to remove the governor from a golf cart. Step 1: Releasing the air pressure from the tires. The first step is to remove all air from the tires of your golf cart. This is done so that you can place it on a jack without the possibility for it tipping over and falling off.
How do you turn the Governor arm on a golf cart?
Feb 02, 2022 · How To Take The Governor Off A Yamaha Golf Cart? 02.02.2022 Indonesia Leave a Reply General Instructions Detach the cable from the carburetor. The cable is about the width of a straw. Follow the disconnected cable up to the governor. Disconnect the gas pedal cable from the governor and reroute it to the carburetor.
How do you remove the governor on a riding lawn mower?
How to Take the Governor Off a Golf Cart - Modesto Muni Golf Gift www.modestomunigolf.com. The governor is a device typically located near the battery pack, and it regulates the flow of electricity to the motor. The golf cart can travel faster than its …
How do you bypass a governor on a carburetor?
How To Take The Governor Off A Ezgo Golf Cart? - The ... Top www.theannikaacademy.com. How Do I Make My Ez Go Golf Cart Idle? Connect the throttle cable to the valve body of the engine as it is in the gas pedal position.Taking the golf cart off your table won't shut it off.Rather than leave it in park, screw the throttle back into place after a few seconds.
How do you take the governor off a electric golf cart?
0:101:28Golf Tips & Etiquette : Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat actually governs the speed. It's very dangerous to take the governor off or to turn it off on aMoreThat actually governs the speed. It's very dangerous to take the governor off or to turn it off on a cart in the fact that that with a cart you have full speed or coasting.
How can I make my golf cart governor faster?
If you find this rod, then your governor can be easily adjusted by accessing the cart's inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart's governance to increase the overall speed.
Where is the governor on a Club Car golf cart?
0:061:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment.MoreWell a golf cart's governor located is actually down in the motor. Compartment.
How do you bypass the governor on a EZ Go golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How fast can a golf cart go without a governor?
Consult with your golf cart manufacturer, but replacing your speed control can increase your speed to 20 mph or more, depending on your upgrade. A typical electric cart without an upgraded speed control tops out around 12 mph.
How do you adjust the governor on a Club Car golf cart?
This governor can be adjusted by adjusting the cable nut which holds the cable to the throttle lever. By making the cable longer, you effectively prevent it from pulling back the throttle lever, producing a higher top speed for your golf cart.Sep 5, 2004
How do you adjust the governor on a electric club car?
Basically, an electric speed governor can be controlled by a tiny metal rod that's located by the clutch of your golf cart. First things first: The electric speed governor is connected to a cable. You can adjust your speed by rotating the nut in a counterclockwise rotation.Aug 29, 2019
How do you adjust the governor on a Club Car Precedent?
0:061:31Club Car Precedent Speed Increase SUPER EASY!!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. AndMoreIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. And if you turn it that way or clockwise it speeds things up. Very. Very simple loosen that bolt.
What do you need to tighten a golf cart?
First of all, you’ll need a handful of wrenches that can be easily adjusted. These wrenches will be used to do things like tighten the governor screw on a golf cart and make it easier to tweak. You may also need some wrenches to open up your engine or other panels on your cart.
How fast is an EZGO golf cart?
A typical EZGO golf cart has a top speed of about 15 miles per hour or so and removing the governor is known to add another seven or eight miles per hour to its operating speed.
How fast can a golf cart go?
That may seem disappointing but is just part of how the cart operates. You may, therefore, only be capable of speeds of up to 10-15 miles per hour.
Why do golf carts have governors?
Golf cart manufacturers put a governor on their vehicles for a reason – they enhance the safety of a cart and keep it from becoming potentially dangerous to a driver. By removing the governor, you are increasing the speed of a cart that may not have extensive crash protection design or even seatbelts.
What happens if you crash 20 miles per hour?
So if you crash when driving 20 miles per hour versus five miles per hour, you are likely to cause four times the amount of damage. And even if you only get double the speed, that’s still double the danger. And don’t forget that you’re also putting more strain on your cart’s motor, as well.
Can you remove the governor from a cart engine?
However, there is also a part known as a governor that keeps your cart’s speed at a safer and more reasonable level. Here’s another fun fact, though: you can remove or deactivate the governor from your cart engine to speed up your cart. You need to be very careful when you perform this step, though, because you may end up making a mistake ...
Can you remove the governor from a golf cart?
People who try to remove the governor from their golf cart often have inflated ideas of what this process will do for their performance. Some may think that they can suddenly jump up to speeds that make their cart a low-speed vehicle. However, that is very rarely the case.
What is a governor and how does it work ?
A governor is a device that automatically restricts the flow or speed of a machine. In case you consider applying this modification to your golf cart, note that it will make the engine run faster and with greater thrust which, in turn, will result in higher speeds.
How to remove the governor from a golf cart
The first step is to remove all air from the tires of your golf cart. This is done so that you can place it on a jack without the possibility for it tipping over and falling off. Refer to your owner’s manual if you’re not sure how to do this since each model uses different methods.
Why would you want to do this ?
There are two reasons why some golf cart owners decide to remove the governor from their vehicles.
Safety tips when removing the governor from your golf cart
Removing the governor from your golf cart is a job which requires that you respect certain safety precautions.
Final Thought
Now that you know more about how to remove your governor from a golf cart, go out and do it. However keep in mind that doing so will permanently disable the governor on your golf cart . This means you will lose control over the speed of your engine no matter what you do .
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
