Most importantly, when removing a clubhead from a graphite shaft it is imperative that the clubhead be removed by pulling it straight off of the shaft. Twisting and pulling on the clubhead to remove it from the shaft (like you would on a steel shaft) will result into a shaft tip failure. A graphite shaft puller is an absolute must for this job.
How do you replace a golf club shaft?
How To Re-Shaft Your Steel Golf Clubs
- Carefully clamp the shaft into a vise using a Shaft Vise Clamp. ...
- When removing steel shafts from clubheads, use a torch to heat the hosel. ...
- After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head. ...
- Using a wire brush remove excess epoxy from the inside of the hosel.
How to remove a golf shaft without a puller?
How to Remove a Golf Shaft From the Head
- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How do I clean up golf club shafts?
Prevention is Better Than Cure
- Wipe your clubs down with cotton after every round
- Wipe your clubs with a multipurpose lubricant in every few months
- Never store them in a humid location i.e. garage, corner of a storeroom.
- Closely monitor the clubs once a month.
- Spray rust remover on metal club heads and shafts. ...
- Dry out properly before storing your clubs if they get wet.
Can you change a shaft from graphite to steel?
Steel iron shafts have been the standard for decades, but that doesn't mean they should be the standard for you. Unless you're a pro, you should take a serious look at switching out to graphite.
How do you remove a golf club head from the shaft?
1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.
How do you remove graphite shaft without a puller?
0:556:40pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steelMoreNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steel on steel I don't see anything wrong with it it's just a much bigger. Application of the heat.
How do you remove a graphite iron shaft?
0:353:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
How do you remove a wedge head from a shaft?
As you apply heat to the hosel (by keeping the heat moving around the whole area), you should periodically try and twist the head and shaft. If they don't budge, keep applying heat. Eventually you will feel the epoxy break and will be able to twist the head off.
How do I make a graphite shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do you replace a golf club head?
1:4010:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipProbably start off on high but you want to move it around on actual the hostile here kind of andMoreProbably start off on high but you want to move it around on actual the hostile here kind of and spinning it around a little bit and make sure you get this superhot.
How do you replace a graphite golf shaft?
4:297:38How to Install Graphite Golf Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe butt of the shaft on a hard surface to ensure the shaft is installed to the bottom of the hosel.MoreThe butt of the shaft on a hard surface to ensure the shaft is installed to the bottom of the hosel. Remove the head and place some epoxy inside the hosel dip the tip of the shaft into the epoxy mix.
Can you reuse graphite golf shaft?
Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely. The only way a graphite shaft will become unusable aside from some freak accidents is by human error in part of the build or an out of control temper on the course.
How are golf club heads attached to the shaft?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
How do you cut a graphite shaft?
1:2914:05Golf Club Repair - How To cut a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you're gonna if this is going to be your primary cutting tool don't skimp alright I'm a big toolMoreIf you're gonna if this is going to be your primary cutting tool don't skimp alright I'm a big tool nut don't skimp even if it's a hand tool.
How do you change driver heads?
1:465:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp as that shaft heats the epoxy starts to break down. And then the shaft the head of the club willMoreUp as that shaft heats the epoxy starts to break down. And then the shaft the head of the club will come will pull off of that shaft. Once that epoxy gives way then you can turn your heat gun.
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How to get glue out of a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue. As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
How to get rid of loose glue?
Twist it to remove loose glue. A small amount of mineral spirits will help clean out the area.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
How to catch a club head off a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
How to get the head off a golf club?
Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.
Is a stock shaft good for golf?
Golf shafts come in a variety of materials, flexes and specifications. Often, the stock shaft is not the best choice for your particular game. You may remove the original shaft and replace it with one that more closely fits your abilities. When considering a new shaft, note features such as weight, length, kick point and flex.
How to twist a golf club head?
Remove heat from the hosel and twist the club head counterclockwise. It should twist off fairly easily. If it does not, apply more heat.
How to remove graphite from hosel?
Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
