Golf-FAQ.com

how to take the heads of golf clubs

by Franco Buckridge Published 3 years ago Updated 2 years ago
image

When packing your clubs in preparation for transit, take the time to remove the heads off of your woods. Use a torque wrench (these usually come with a driver when you purchase it) to loosen the screw where the shaft meets the head and take it all the way off.

Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.

Full Answer

How do you remove a golf shaft from the head?

Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly. Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel.

How do you fix a broken golf clubhead?

Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue. As you apply heat, grab the clubhead and gently turn it to begin working it out.

How do I remove the hosel from the clubhead?

Apply a heat gun to the hosel to melt the epoxy glue. The hosel is the area at the base of the clubhead where the shaft is inserted. Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.

How do you remove epoxy from a golf club head?

Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.

image

How do you remove a head from your shaft?

1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.

How do you remove a club head from an iron shaft?

How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...

How do you remove a driver head?

0:514:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you may want to use a heat gun and that's perfectly. Fine just remember it's going to probablyMoreAnd you may want to use a heat gun and that's perfectly. Fine just remember it's going to probably take you about three times longer because it's not as high a concentration of heat.

How do you remove a golf head from a graphite shaft?

0:015:40How to Remove a Golf Shaft | DIY project Graphite Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i'm in my garage this morning. And what i want to show you is how to remove a um club head fromMoreSo i'm in my garage this morning. And what i want to show you is how to remove a um club head from the uh from a shaft. This particular one is a graphite shaft. So you got to be extra careful uh i did

How do you remove a club head from a golf club?

Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.

How do you replace club heads?

1:4010:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipProbably start off on high but you want to move it around on actual the hostile here kind of andMoreProbably start off on high but you want to move it around on actual the hostile here kind of and spinning it around a little bit and make sure you get this superhot.

Should you remove driver head when traveling?

Removing the club heads decreases the likelihood of the heads getting snapped off in transit, one of the easiest ways of mastering how to protect your golf clubs when flying. Simply wrap the club head in a golf towel or a headcover and store it in an extra pocket of your golf bag.

How do you remove the head of a Taylormade m2 driver?

0:455:30How to adjust your Taylormade M2 2017 driver - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere let's open or loosen the shaft screw you place this adjustment wrench into the screw here andMoreHere let's open or loosen the shaft screw you place this adjustment wrench into the screw here and you turn it anti-clockwise to open to tighten the screw.

Can you put any driver head on any shaft?

Yes, most golf Driver shafts are interchangeable. Golf driver shafts can be replaced as long as the new shaft is the same length and made by the same brand of golf club.

Can you pull a graphite shaft without a shaft puller?

Well, the general process for pulling a graphite shaft is just about the same, but there are a few key differences. You need to take more care and HAVE to use a shaft puller. Otherwise, your new fancy and expensive exotic shaft could be at serious risk for major damage.

How do you make a golf club shaft puller?

0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.

How do you remove a graphite shaft at home?

0:556:40pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steelMoreNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steel on steel I don't see anything wrong with it it's just a much bigger. Application of the heat.

How to get glue out of a golf club?

Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue. As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force.

How to remove a ferrule from a hosel?

The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.

How to get rid of loose glue?

Twist it to remove loose glue. A small amount of mineral spirits will help clean out the area.

Do you need to reshaft a golf club?

The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.

How to catch a club head off a golf club?

Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.

What to do if your golf club shaft is bent?

If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.

How to remove ferrule from golf club?

Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.

How to get the head off a golf club?

Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.

How to heat a hosel?

Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense heat evenly on all sides of the hosel and don't be alarmed if small amounts of white smoke begin to escape the hosel cavity. That is just the old epoxy melting.

Is a stock shaft good for golf?

Golf shafts come in a variety of materials, flexes and specifications. Often, the stock shaft is not the best choice for your particular game. You may remove the original shaft and replace it with one that more closely fits your abilities. When considering a new shaft, note features such as weight, length, kick point and flex.

scooducks

Do you guys remove the heads from fairways/drivers and store them in a bag pocket when packing the sticks?

downlowkey

I fly with an SKB hard shell and always remove the driver head. Sent from my iPhone using MyGolfSpy

Rikki03038

Never have. I have a soft travel case and have yet to ever have an issue

scooducks

Ship them to your destination. Way less hassle than dragging that damn golf travel bag through the airport and rental cars... I haven't flown with clubs since 2007.

scooducks

There is a FedEx Ship Center in the Middle of Martha's Vineyard. Or even straight to Farm Neck GC... Just check with the Pro first. I am sure they would be accommodating..

Jiro

If you have a soft bag, get a stiff arm or a pvc pipe slightly longer than your longest stick. If your driver head is removable, removing it is probably the safest route.

Peterpc2828

I have a soft bag and before heads were removable on my first trip to play the blue monster at Doral I opened my bag upon arrival to the course to find my driver head snapped at the tip, luckily the course realized what happened and lent me a very nice driver for my round of golf.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9