To determine the ferrule size required, measure the shaft of the stick or frame; it is likely to measure between 18mm and 25mm depending on the stick or frame type. Alternatively, measure the inner diameter of the ferrule you have removed.
Full Answer
What does a loose ferrule look like on a golf club?
Or wobble or even spin around. Or slide up and down a bit on the shaft. Don't worry: In most cases, a loose ferrule is not a sign of a major problem with the golf club. It's probably just a sign that the glue holding the ferrule in place has loosened over time.
Do I need a ferrule on my club?
You can trust that the club will not start to twist over time or anything if you have a ferrule in place. Obviously this is not fully guaranteed but it certainly helps add more sturdiness to the connection.
Are all ferrule shafts the same size?
There are ferrules manufactured to different inside diameters to accommodate all different shaft tips. In addition, the outside diameters of a ferrule all don’t have the same exact diameter. Keep in mind as well that the hosels of clubheads aren’t all the same size either.
What is a collared ferrule on a golf club?
The collared ferrules are precision manufactured pieces. However, the countersink of a clubhead is done quickly at the foundry to remove any material from the interior of the hosel.
How do you know what size ferrule you need?
You must measure your walking stick to find out what ferrule size you need. You must measure the diameter of the walking stick without a ferrule. A walking stick with a diameter of 22mm without a ferrule needs a ferrule of 22mm.
How are golf ferrules measured?
Standard iron ferrules are from 1/8 to 1 1/4 inches long with an internal diameter of . 368 inch, while standard wood ferrules measure from 1/8 to 3/4 inch long with an inside diameter of . 334 inch.
How do I know what size hosel to get?
If you're not sure what the hosel ID is, you can measure it with a fine tip gauge or contact the club manufacturer for this information. On the opposite side of the shaft is the butt end. This is the side where the golf grip will be installed. The butt diameter is measured about 2" down from the top of the shaft.
How do you measure a golf club hosel?
Measure your shaft tip using a golf shaft identification gauge by placing the shaft tip into the hole that fits most snugly and reading the number that is by that hole. The tip thickness range is from . 270 to . 370 inch.
Can you reuse a golf ferrule?
Can You Reuse Old Ferrules? If you manage to get used ferrules off without damaging or cutting them, then yes, you can reuse them. Depending on what was used to install them, it can be really easy or almost impossible to get them off undamaged.
How much does it cost to replace a ferrule golf club?
Remove Rattle: easy fix -- $5.00 / hard fix -- $20.00. Replace Ferrule -- $12.50. Repair Ferrule -- $5.00.
How do you measure a golf club shaft?
A 48” golf club ruler is placed along the backside of the club with the tip of the rule touching the ground by the club's heel. The final length is measured at the edge of the grip cap (and not the very top). This method is used in all cases except putters that the shaft is not located at the heel.
What tip size are Callaway irons?
0.370”This is by design as Callaway starts out by using a 0.370” parallel tip shaft. Callaway's hosels are slightly tapered so that when the shaft is inserted it pinches in the split shaft and forms a pseudo-mechanical lock.
How do you measure golf grip diameter?
The diameter of the grip, which is already installed on the shaft, is measured at a point two inches down from the edge of the grip cap – see picture below. Usually male golfers use “standard” grips and female golfers use “ladies” grips. But in many cases it isn't the best solution.
How do you measure golf clubs for yourself?
3:0615:40ARE MY CLUBS THE RIGHT LENGTH? FIND THE CORRECT GOLF ...YouTubeStart of suggested clipEnd of suggested clipStand in normal standing upright posture with your arms at your sides. And you're just going to takeMoreStand in normal standing upright posture with your arms at your sides. And you're just going to take a ruler just a standard yardstick. And you're going to measure.
What is tip diameter?
The outside diameter (or the tip diameter) is the diameter of the circle produced by connecting the tooth tips. In standard gears, the outside diameter can be expressed as a formula as shown below. da = d + 2m.
What does the tip size mean on a golf shaft?
Refers to the diameter of the tip end of a golf club shaft, that portion which attaches to the clubhead. If you're making or repairing a club, be sure to order a shaft with the tip size matching the aperture of the hosel. Typical values are .
What is the I.D. of a 355 ferrule?
.355 ferrule = .370 I.D. since the tapered tip is but 1/8" or a little bit more, rest of the tip is .370. I often wonder why some advertise the ferrule to be .355.
What happens if you force a 355 ferrule on a 370 shaft?
If forced the .355 ferrule onto the .370 shaft, that will either split the ferrule on a steel shaft or damage the graphite shaft. Anyone do this on a regular base will know how tight a fit a ferrule should be.
What is the ID number for a 350 shaft?
There is no real standard for what the ID's might be or should be based on how they are labeled or sold. In some cases a ferrule labelled for .350 shaft might actually have an ID of .350 (and not be tight at all) or it might be 0.345, .340, .335 or any number really.
How long should I soak a ferrule in water?
Actually it will with no problems - IF you soak the ferrule in boiling water for about 10 seconds. It softens them enough to easily stretch to the proper size. Slips on using the actual hosel to push with no undue effort, no damage to either the shafts (graphite) or ferrule itself. I've done it frequently.
Can you use a 355 ferrule on a 370?
Yes, there are .355 ferrule out there , normally I use them for .350 tip, too much elbow grease to file it open to .370 if doing a proper job with hand tool. .355 ferrule will NOT slide onto the .370 tip . The only way is to file the I.D. with a rat tail file to make it fit.
Can a 355 ferrule be used with a 355 ID?
While you are correct about the shaft size (except the taper extends over ~1/2", not 1/8"), Despite that, many .355 ferrules are still actually made with a .355 ID. Yes it's crazy IMO but it happens non-the-less. And yes, it does result in a ferrule that's extremely tight but can still be used (with boiling water to loosen it up to get it into place).
Can a 335 shaft slide up?
Sounds like your shaft is a .335 (or possibly your ferrule is .370?) They should not slide up and down freely, no. I keep a cheap ($10) Harbor Freight digital caliper on my bench for situations just like this. Every clubmaker should have one! :taunt:
Why do you need a ferrule on a golf club?
The main advantage of having a ferrule is that your club will be able to take more stress throughout your swing. You can trust that the club will not start to twist over time or anything if you have a ferrule in place. Obviously this is not fully guaranteed but it certainly helps add more sturdiness to the connection.
How to protect a golf club shaft?
Always cut away from yourself and in the direction of the fibres of the shaft to help protect it as much as possible. Follow the guidance in the link above or have your pro do it. They are trained in these things and have done it before so your club may be safer in their hands.
What is an uncollared ferrule?
Uncollared ferrules sit flush on the neck of the club and will have epoxy in the inner surface of the ferrule, as will the collared version, just not the added layer at the connection point. Collared ferrules are a more recent development in the golf world.
What does a ferule do?
What Exactly Does A Ferrule Do? Ferrules are seen on many objects from paint brushes to tow cables and even golf flags. They are additions to a structure that help fasten or secure two things together. So, in terms of the golf club, which is why we are here, it helps secure the head of the club to the shaft.
What is the best alternative to plastic for golf clubs?
It is important that the material used is strong and light, you don’t want to affect swing weighting of the club. Aluminium is a great alternative to plastic for this reason.
What happens if a golf club moves?
If the club is moving then you have a bigger issue and the club needs to be fixed. Again, have your pro do this, they can re-bind everything and inspect the club to ensure there’s been no damage.
Where does the adjustability of a golf club come from?
The adjustability of these clubs comes from an adaptor between the top of the neck of the club and the shaft, this means the ferrule has to be on top that. It means that, in this case, the very bottom of the shaft actually becomes part of the clubhead, in effect.
What is the sloping scale for golf?
Most charts have a sloping scale for the height and wrist-to-floor, with player’s height on X and wrist-to-floor height on Y. These two measurements combined give the club length and a lie angle for irons to test.
How does length help in golf?
Getting the right length can prolong your golfing career and help you hit the ball longer by improving your ball striking. Better ball striking also means more consistent carry distances.
What happens if the club is too long?
If the club is too long, the face tape may show heel dominant striking. If the club is too short, the face tape may show toe dominant striking. If dominant striking is found, the demo length should be changed accordingly. This is to see whether the impact location changes with the length.
What are the problems with driving a golf club?
Direction problems: When looking at the driver length, too long can lead to inconsistent ball striking or strikes towards the heel. Heel strikes encourage left-to-right curvature i.e. Fade, cut, slice or push slice. Strike problems: Ball striking can be more difficult if your club is too long.
What is the average driver length for Rickie Fowler?
Rickie Fowler is known to have used a 43.5” driver length and the Tour average build is 44.5”. Tour players main priority is hitting fairways for days, weeks and months. Shorter driver lengths make it easier to hit with the centre of the face more frequently.
What happens if you have too short of a club?
Direction problems: Too short club length can lead to strikes towards the toe or low on the face. Toe strikes encourage right-to-left curvature i.e. Draw, hook or pull hook. Strike problems: With too short club length, the most common problem is ‘Thin’ shots (hitting higher on the ball).
What can you use to wipe off golf ball?
You could use something that will wipe off like water or marker pens on the golf ball to give yourself some easy feedback on the clubface.
What is the role of a ferrule in golf?
The role of the ferrule is to provide a smooth transition from the shaft to the hosel. With a ferrule, a golfer doesn't see the (sometimes) sharp edges of the hosel where the shaft enters the clubhead. The ferrule covers that up.
What is the ferrule on a titleist iron?
The ferrule, a black, plastic ring or sheath, is noted on this image of Titleist iron. The Acushnet Company. Brent Kelley is an award-winning sports journalist and golf expert with over 30 years in print and online journalism.
Why do irons have a band around the shaft?
In the early days of golf, when irons had shafts made of hickory, placing a band around the point where the shaft entered the clubhead did serve a purpose: It helped prevent the wooden shaft from splintering or shattering. But when wooden shafts disappeared from golf, ferrules took on a mostly cosmetic role.
What does it mean when a golf club is loose?
Or wobble or even spin around. Or slide up and down a bit on the shaft. Don't worry: In most cases, a loose ferrule is not a sign of a major problem with the golf club. It's probably just a sign that the glue holding the ferrule in place has loosened over time.
How to fix a loose golf club?
First, check to make sure the clubhead itself feels secure. If you detect any looseness in the clubhead, then, yes, you have a problem and should visit a club repair shop. If the clubhead feels solid (and feels the same when you hit golf shots as it did before you noticed the loose ferrule), then you almost certainly just need to re-secure the ferrule. And you can that with a small amount of epoxy glue.
Where is whipping on a golf club?
Whipping was a strong thread wrapped around the hosel area, about an inch above and below where the hosel and clubhead joined. With modern metal woods and steel and graphite shafts, however, whipping is gone from golf. A wood will either have a ferrule or no cover at all over the hosel/clubhead joint.)
Can you replace a golf club ferrule with a new one?
And they are cheap! Replacing a cracked or broken ferrule with a new one, however, does require removing the clubhead.
How to determine the correct size golf club for beginners?
The correct golf club size starts with the golfer’s height and wrist-to-floor measurement.
What factors affect the size of a golf club?
Here’s another factor that affects the appropriate golf club size. The angle and the grip size of the club are as important as the height and wrist-to-floor measurements . However, this means more to serious professional golfers than to someone just starting out.
What is custom fitting golf?
Custom golf fittings will tell you the exact sizes that you need for each of your golf clubs. Knowing the proper golf club sizes will ensure that you can get the clubface to match up to the ball each and every time you swing. The more accurate your club sizes are, the better the chance you have of scoring and performing. Even though custom golf fittings can be expensive, most golfers find them to be very well worth the pricing.
How to adjust golf clubs?
If you find that your golf clubs are not the exact length you need, you can adjust them by cutting or extending the clubs and then regripping them . If you don’t have the tools to do this yourself, there are typically local golf club repair shops that offer these services.
Why do manufacturers make golf tables?
Manufacturers create such tables to help everyone from beginner golfers to pro golfers choose the right club size for their play. Here’s how your size affects the dimensions of your needed golf club size and why it matters. Last but not least, the grip size should also be determined for the club to fit perfectly in your hands.
What is the difference between men's and women's golf clubs?
The difference between men’s and women’s clubs is generally noticeable on the grip. Men’s golf clubs have larger grips and are also about 2.5 cm longer than women’s golf clubs. Kids’ clubs are even smaller than women’s for the most part. Knowing what type of golf club you need is the first step in determining the appropriate size.
How tall is a golf club?
Manufacturers usually make clubs to account for golfers anywhere between 4’8” to 6’7” inches tall. The second measurement is wrist-to-floor distance. This is done by standing on a flat surface with your arms relaxed and pointing down. You then measure the distance between the ground and the line where your wrist meets your hand.
What is a ferrule on a golf club?
Definition. A ring that covers the entry point of the shaft where it connects to the hosel of the clubhead. The ferrule serves to hide the joint between the shaft and the club head and it is usually made of hard plastic in a dark color.
Do golf clubs have ferrules?
The ferrule is an optional component in a golf club and some club manufacturers choose not to use ferrules in their clubs at all, such as Ping, leaving the joint exposed instead.
What is a ferrule in golf?
The purpose of a ferrule is to provide a smooth transition from the top of the hosel into the shaft. For the most part it is to provide a nice cosmetic element to the golf club. The ferrules are typically manufactured from plastic and may be all black or have colored trim ...
What size ferrules are used for titanium drivers?
Since aluminum woods are not found often today, most wood ferrules are made closer to the 0.500” outside diameter for both titanium drivers and stainless fairways alike. The ferrules on the fairways will need to be sanded to size.
What is a collared ferrule?
One of which is called a “collared” ferrule. These ferrules have a flange below the ferrule itself that fit into the countersunk portion of the hosel in order to reduce stress of the shaft. The collared ferrules are precision manufactured pieces.
What size iron head for hireko?
At Hireko, we try to manufacturer all our iron heads with approximately the same diameter (0.540” or 13.7mm) so most of our ferrules we stock fit very close. Woods on the other hand may not all have the same diameters because of the different materials the hosels are made from and the dimensions needed for strength. Many titanium drivers have hosel diameters close to 0.500” (12.7mm), while stainless steel fairway woods measure closer to 0.480” (or 12.2mm). Add in aluminum woods, and you have a third dimension of @ 0.515” (13mm). Since aluminum woods are not found often today, most wood ferrules are made closer to the 0.500” outside diameter for both titanium drivers and stainless fairways alike. The ferrules on the fairways will need to be sanded to size.
Do you have to countersink a collared ferrule?
Unfortunately, it may be required to re-countersink the hosel in order for the collared ferrule to fit flush.
Do hosels match outside diameter?
outside diameters of the hosels as they are hand polished during the finishing process. Therefore the ferrules and hosel will not match outside diameter for outside diameter each time. This is the reason why turning down the ferrule is the most acceptable method.
Is a clubmaker's ferrule larger than a hosel?
Knowing these dimensions can save you time when ordering. In years past, the outside diameter of the ferrule was typically larger than the average hosel, so that the clubmaker could be “turn down” or sand the ferrule flush with the outside diameter of the hosel to provide a smooth transition.
