See if you can hear the solenoid click when you press the pedal. Provided that you have enough power to run your cart, the next thing you should hear is a click from the solenoid. If there is voltage present and the pack reads the combined voltage necessary (36v or 48v) but no sound from the solenoid, it is time to really dig into the electrics.
Full Answer
How to test a golf cart motor for a short?
How To Test Your Golf Cart Motor For A Short Begin by labeling the cables going to your electric motor and put a corresponding label on the motor itself if it does not already have one. Assuming that we’re using a multimeter and not just a continuity tester, set your tester to the continuity setting and if it doesn’t have one, set it for ohms.
How do you test a motor with 36/48 volts?
· SERIES wound motor test: Jack the rear tires of the ground and put the cart on jack stands... Remove the main positive and negative cables form the battery pack... Spray the 4 studs on the motor with a little penetrating oil... Mark the cables then remove all four cables from the motor (use a wrench to hold the jam nuts)...
What kind of motor does a golf cart have?
· This is to bypass the speed controller to diagnose if a cart has a good motor.
How do I know if my golf cart motor is bad?
· a. Regen motors have "shunt" or "round wire" coils, usually with smaller gauge wire (12AWG - 24AWG range). Usuaully, with a large amount of turns (60 to 200+ turns) per field coil. b. Series motors have "flat wire" coils with larger wire sizes. Usually, the wire is rectanular in shape (cross-section).
How do I know if my electric golf cart motor is bad?
You have enough going on in your life without your golf car refusing to start when you turn the key in the ignition. If your golf car won't start, is slower than it used to be, or is experiencing other technical problems, you could have a bad motor on your hands.
How do you test a Club car golf cart motor?
Connect the positive jumper cable to the positive battery terminal on the 12-volt battery. Touch the other end of the positive battery cable to the A2 terminal on the electric motor. Once the positive battery cable touches the A2 terminal, the motor should start turning and the rear wheels should start turning as well.
How do you test a golf cart motor controller?
Connect the negative probe to the controller's M terminal and positive probe to the B+ terminal. Press the accelerator and watch to see if the voltage increases. It should increase from a reading of 0 to the full voltage of the battery. If the motor is not turning, the problem may be in the directional switch or motor.
How do you test a 36v solenoid?
Set your multimeter to ohms and insert a probe on each large terminal with the key off and the cart direction switch in the neutral position. Press on the accelerator with the cart's movement control in the forward position, and the key is turned on. A click should be heard first from the solenoid.
How do you test a motor for continuity?
You should test the windings for a “short to ground” in the circuit and open or shorts in the windings. To test your motor for short to ground, you'll need to set the multimeter to ohms and disconnect the motor from its power source. Then inspect each wire and look for infinite readings.
What are the 4 terminals on a golf cart motor?
If you're unsure if it is working, it is simple to test. There are four terminals on a solenoid: usually two large and two small. The small terminals are connected to the battery, and the large terminals are connected to the motor. Disconnect all wires from the two large terminals.
How do I know if my golf cart controller is bad?
When your golf cart's speed controller isn't operating correctly, your cart will show it by running erratically or failing to drive at one constant speed. If your cart starts showing these symptoms, the first thing you should look at is your speed controller.
How do I reset my golf cart motor?
First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!
How do I reset my club car motor?
Easily Reset the Club Car Golf Cart OBCKey switch to off.Set forward/reverse to neutral.Put tow/run switch to tow.Disconnect the negative battery terminal from the battery pack.Put the tow/run switch to run.Put forward/reverse switch to reverse.Put key switch to on.More items...
How do you test a 36v ezgo solenoid?
This can Also be tested by putting a test lead on each small terminal and pressing the gas pedal. The meter should read 36 V when the gas is pressed. If this voltage does exist when the gas pedal is pressed then the solenoid should click and engage.
What happens when golf cart solenoid goes bad?
If the solenoid is broken and not working correctly, you may notice your golf cart won't start, picking up speed, or even working at all (issues with acceleration could also be caused by a bad speed controller).
Why does my golf cart click but not move?
A damaged battery or damage to the internal controller could cause your club vehicle to make a clicking sound but not move. Due to dust building inside the battery ports, a Club Car golf cart can start clicking but not move. These are the causes of clicking sound on the golf cart but won't move, among others.
How To Tell If Your Electric Golf Cart Motor Is Bad
Even the most well-maintained golf car will have technical problems eventually. Still, it’s rather unfortunate if the problem is with your motor or engine. You have enough going on in your life without your golf car refusing to start when you turn the key in the ignition.
Test Your Batteries
When your golf car doesn’t start, it’s tempting to jump straight to the perceived problem area: the motor. But the issue could be a simpler one concerning another part of the car. Before checking its other parts, test the voltage of your batteries to make sure they’re working.
Check the Solenoid
If your batteries are charged and in working condition, but your car still won’t start, check its solenoid. A solenoid is an electromagnetic coil of wire that transmits energy from your car’s battery to its motor to help it start. Every time you start your golf car, you should hear the click of the solenoid.
Examine the Potentiometer
If your car still won’t start or you notice any issues with acceleration, it’s time to check the potentiometer. The potentiometer sends an electric signal from the accelerator pedal to the speed controller, allowing the car to accelerate properly.
Check the Motor Itself
If you’ve checked all the above parts and none of them are responsible for your trouble, inspect the motor of the golf car itself. Sometimes, the issue can be resolved by simply resetting the motor. To reset your golf car’s motor, open the hood to expose your motor and look for the red reset button.
What is a club car?
by Kevin Mclain. A club car is an electric-powered utility vehicle that is mainly used as a golf cart. Club cars can also used to move people more efficiently around places where regular vehicles will not fit.
How to remove battery post nuts?
Remove the nuts from each of the four battery posts that hold the wires in place. Place the nuts in a safe area and pull the wires off of the electric motor. Connect a jumper wire from the A1 post to the S1 post on the electric motor. Screw the battery post nuts on and tighten the nuts with the adjustable wrench.
Can you hook jumper cables backwards?
Do not hook the jumper cables up backwards or it could cause the battery to blow up and damage the electric motor. Writer Bio. Kevin Mclain has more than 20 years of automotive, home improvement and landscaping experience. He has been writing for various online publications since 2002.
