how to test micro switch on ezgo gas golf cart

^{How to Test EZGO Micro Switch}

1. Access the Micro Switch. Most of the micro switches on EZGO golf carts including the EZGO TXT, EZGO RXV, and EZGO Express are located beneath the cart ...
2. Connect a Voltmeter. The micro switch will have two wires connected to it. ...
3. Check for Continuity. With the switch in its original position and in the alternate position, check the readings in the voltmeter from the micro switch.
4. Reset the Switch. Once the continuity test is completed, remove the voltmeter and connect the two wires back to the micro switch.

Where is the micro switch on an EZGO golf cart?

In most of the EZGO models, it is located on the bottom side of the cart near the accelerator pedal. Unscrew the outer covering and access the two terminals of the micro switch.

How to test the solenoid on an EZGO golf cart?

How to test the solenoid on an EZGO golf cart? If the gold cart shows certain bad solenoid symptoms like not starting, no clicking sound, or starter disengaging, it is better to test the solenoid. You can test the solenoid by simply disconnecting the main circuit high wires and by using a multimeter.

How do you test a micro switch on a golf cart?

Check the position of the micro switch in your golf cart using the user manual as a reference. If the micro switch is out of position, rewire it to the expected position. If the micro switch is in its expected position, conduct a continuity test as mentioned above by connecting a voltmeter across it.

What happens when the micro switch goes bad on an EZGO?

A faulty micro switch leaves the nearby components damaged due to a low or unrated power supply. A dislocated micro switch can disturb the normal operation of other components. To make sure no further damage is caused to your EZGO golf cart, it is necessary to address a bad micro switch at the earliest.

How do I test my EZ GO micro switch?

Depress the pedal slowly. The reading should be 0.45 - 0.53 volts just as the micro-switch is activated. Depress the pedal slowly to full throttle. The reading should move smoothly to about 1.5 volts.

How do you test a micro switch on a gas golf cart?

Again, leave your black probe on the battery negative terminal and use your red probe for testing. With the key switch ON, you should read battery voltage at the common terminal (C or COM), but not the other terminal. Once the micro switch is activated, you should read voltage on both terminals.

What does the micro switch do on a golf cart?

Microswitches are used in many golf cart applications. They are used at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go. In an electric golf cart, the solenoid sends power to the controller to move the cart.

How do you test a FR switch on an EZ Go golf cart?

Check all the connections and make sure each part is getting power by using the multimeter. Have your foot firmly on the brake, put in the key, and the F/R switch in the forward position. When you push the go pedal if the solenoid charges up then your EZGO F/R switch is good to go.

How do you test if a micro switch is working?

2:134:10Electric shower problems: How to test a microswitch. - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is the normal micro switch and normally. The power comes in the top connection. Here and whenMoreThis is the normal micro switch and normally. The power comes in the top connection. Here and when the buttons pressed it goes out here and off to the elements or whatever.

How do you test a ezgo gas solenoid on a golf cart?

Press on the accelerator while the key is turned on and the cart is in forward.The solenoid needs to be replaced IF the voltmeter shows a full battery voltage without a click.If your voltmeter stays at 0, the problem stems from somewhere else in your cart.

How do you bypass a micro switch on a golf cart?

You can bypass the reed switch in an EZGO golf cart by connecting the red wire of the reed switch to the white wire from the charger receptacles and to the red wire from the FRN micro switch.

Where is the micro switch located on a golf cart?

In a golf cart, you're going to find a large number of these switches throughout its build. For example, there is a micro switch located on the accelerator pedal. This switch activates when you push the pedal and sends a signal to the solenoid.

Why won't my gas golf cart shut off?

Troubleshooting. Switch the car to neutral before turning the key off. The problem with shut down may have occurred from the kill circuit, which is controlled by the top microswitch. You may have to replace the microswitches or solve the problem by tightening up the circuit.

How do I bypass the reed switch on my EZGO?

0:221:131995 36V EZGO Golf Cart Reed switch bypass - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo some form said that the reed valve can be bypassed and that seems to be a pretty common issue.MoreSo some form said that the reed valve can be bypassed and that seems to be a pretty common issue. And here's the charger here and the front I've already taken off the panel and loosened it.

How do you test a throttle inductive sensor?

Take a digital multimeter and set it to the volts reading. Place the positive probe of the meter on the white wire terminal of the ITS. Release the accelerator pedal slowly. The reading should be in the 0.45V to 0.53V range when the micro-switch gets activated.

Why won't my gas golf cart go forward or reverse?

The problem could be with either the Run/Tow switch or Forward/Reverse switch or both. Check the switches to ensure that they aren't stuck midway. If they are, getting them released should help. However, if they show signs of wear and tear, you must get them replaced.

Why is my Ezgo golf cart not clicking?

A EZGO golf cart that is not making a clicking sound can be due to a failed solenoid. If there is no sound in the cart while igniting the switch, then the problem can be the cart’s control circuitry. This means the solenoid has stopped working. Then it is required to replace the solenoid.

How to test gold cart solenoid?

You can test the solenoid by simply disconnecting the main circuit high wires and by using a multimeter.

Why is my cart solenoid getting hot?

If the cart solenoid is getting hot, then the problem can be with the solenoid or the circuit wiring. It is better to check the solenoid thoroughly. Use proper solenoid, which matches the amperage and voltage of the cart system. Use high-quality solenoid to avoid the heating problem.

What to do if solenoid is not working?

If the solenoid is not working after checking and testing the solenoid using a voltmeter, then it is time to replace the solenoid all together. Always be sure of the model and year of the cart. Check online to get all specifications. Compare the online picture of the new solenoid with the older one.

What happens if a cart starts with a solenoid?

If the cart starts, then the solenoid is the problem and, if it does not, then the problem is not solenoid but something else. A cart owner should remember that bypassing the solenoid can damage the ignition system and central circuit of the cart. Also, bypassing should only be used for checking the solenoid and not permanently.

Where is the solenoid located on a golf cart?

The solenoid is located inside the controller box connected to it.

Can you upgrade a golf cart solenoid?

Upgrading the solenoid will allow upgrading the entire golf cart. However, one can upgrade the solenoid even when the stock solenoid is not doing its job properly. Upgrading the solenoid will help in making the cart powerful. The upgraded solenoid can match the controller amperage.