The EZGO speed sensor can be tested by ensuring that the three-pin plug from the sensor is connected. Keep a wire-piercing probe over the output wire. This is usually green in color. Raise one of the wheels of the EZGO golf cart and give it one full rotation using your hand.
Full Answer
How do I test the EZGO golf cart's speed sensor?
Raise one of the wheels of the EZGO golf cart and give it one full rotation using your hand. Note the voltage reading of the cart. If you have a good sensor, the reading must rise to 5V 24 times from 0V for just one rotation. The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller.
How do I bypass the reed switch on my EZGO golf cart?
How do I Bypass the Reed Switch on My EZGO? You can bypass the reed switch in an EZGO golf cart by connecting the red wire of the reed switch to the white wire from the charger receptacles and to the red wire from the FRN micro switch. Ensure that the main power supply is disconnected before accessing the reed switch and charger receptacles.
How do I Turn on the EZGO F/R switch?
Have your foot firmly on the brake, put in the key, and the F/R switch in the forward position. When you push the go pedal if the solenoid charges up then your EZGO F/R switch is good to go.
What if I am not confident in my E-Z-GO golf cart?
It's important to remember that if you are not fully confident in the work you are trying to perform on your E-Z-GO golf cart, consult with your local E-Z-GO dealer to be sure your work gets done properly.
How do you test the speed controller on a EZ Go golf cart?
Connect the negative probe to the controller's M terminal and positive probe to the B+ terminal. Press the accelerator and watch to see if the voltage increases. It should increase from a reading of 0 to the full voltage of the battery. If the motor is not turning, the problem may be in the directional switch or motor.
How do I test my EZGO micro switch?
Depress the pedal slowly. The reading should be 0.45 - 0.53 volts just as the micro-switch is activated. Depress the pedal slowly to full throttle. The reading should move smoothly to about 1.5 volts.
How do you test the inductive throttle sensor on a EZ Go golf cart?
Put the key in the “On” position in your Run/Tow switch on the cart. Switch the F/R switch into a forward position to test your cart. Place your voltimeter testing pins on the throttle pins to see how much voltage you get. When the cart is running with no throttle, you should get about 10 volts here.
Where is the speed sensor on ezgo golf cart?
The speed sensor on an EZGO TXT golf cart is located close to the motor. This sensor is present on the rear side of the motor on the driver's side of the golf cart.
How do you test a golf cart micro switch?
Put the voltmeter probes on the proper terminals. Test With the Voltmeter – At this point, you should be getting a reading from your micro switch. It should read continuity, which means that electricity is flowing through it.
How do you test a golf cart switch?
Use a multimeter to check if all the parts are getting power. Place your foot on the car's brake, insert the key, and put the forward-reverse key in the forward position. If you see that the solenoid charges up pushing the pedal, then your forward reverse switch is working fine.
How does a golf cart speed sensor work?
Magnetic Style. Many golf cart motor speed sensors employ an electromagnetic power to “read” the motor rpm. Generally, there is a magnet present in the closed end of the motor as well as the sensor itself which reads how the magnet is reacting with the magnetic field inside the motor.
Where is the reset button on a ezgo golf cart motor?
Locate the motor Remove the panel so the electric motor is visible. Electric motors usually include reset buttons that can perform similar to circuit breakers. Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
How do you bypass a micro switch on a golf cart?
You can bypass the reed switch in an EZGO golf cart by connecting the red wire of the reed switch to the white wire from the charger receptacles and to the red wire from the FRN micro switch.
How do you test a speed controller on a Club Car golf cart?
To test a club car precedent controller, connect a voltmeter between the negative terminal of your cart's battery and the M terminal on the controller. Then push the pedal down and look for a clicking noise from the solenoid. Your batteries should read as full.
What controls the speed on a golf cart?
Essentially, your golf cart's speed controller sends its current and battery voltage to its motor. This process depends on your golf cart's input device, which includes its throttle. That's how your golf cart's speed controller lets you operate its acceleration rate, as well as its deceleration rate.
Where is the speed sensor located on electric golf cart?
Typically, the speed sensor can be found on the backside of the motor. When removing the speed sensor, unplug all the cables that are on the backside of the motor. To do this, use a socket to take off the connector pigtail. Then, remove its plastic housing over the sensor.