
How to Test Yamaha Golf Cart Solenoid First, disconnect the two small wires connecting the solenoid. Take a jumper cable and connect them from the positive and negative posts of the battery pack to the two posts on the solenoid that you just disconnected.
How do you test a Yamaha golf cart solenoid?
How to Test Yamaha Golf Cart Solenoid First, disconnect the two small wires connecting the solenoid. Take a jumper cable and connect them from the positive and negative posts of the battery pack to the two posts on the solenoid that you just disconnected.
What is an Abad solenoid on a golf cart?
A solenoid is one of the main components in a golf cart that allows it to move. Whether electric or gas, you will find a solenoid in your golf cart. Every golf cart needs a proper solenoid to operate. Here, we’ll discuss the symptoms of abad solenoid on a golf cart.
How many solenoids are used in a golf cart?
The number of single-action solenoids (4-terminal solenoids) used in each golf cart was reduced with the advent of dual-action solenoids (6-terminal solenoids). A good example of a solenoid bank can be seen in the illustration below:
What are the symptoms of a bad solenoid on a golf cart?
Understanding what a solenoid is in a golf cart is vital for troubleshooting and repair. The common symptom of a bad solenoid is no clicks when the cart’s ignition is on and you press the accelerator. How do you test for a bad solenoid in your golf cart?

How do you test a solenoid on a Yamaha golf cart?
Set your multimeter to ohms and insert a probe on each large terminal with the key off and the cart direction switch in the neutral position. Press on the accelerator with the cart's movement control in the forward position, and the key is turned on. A click should be heard first from the solenoid.
How do I know if my solenoid is bad on my golf cart?
First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn't move, then the problem is not with the solenoid. If it jumps and displays full voltage, then the solenoid is the problem and should be replaced with a new one.
How do you bypass a solenoid on a golf cart?
6:077:29Solenoid Bypass - YouTubeYouTubeStart of suggested clipEnd of suggested clipInstead of using big wires that otherwise you'd have to have these these big battery terminal wiresMoreInstead of using big wires that otherwise you'd have to have these these big battery terminal wires go into the back of your -.
How do I test a starter solenoid with a multimeter?
2:283:42How to Test a Starter Solenoid - Summit Racing QuickFlicksYouTubeStart of suggested clipEnd of suggested clipLead hook it up to my negative again and I'm going to go ahead and jump the solenoid the way that I'MoreLead hook it up to my negative again and I'm going to go ahead and jump the solenoid the way that I'm going to do that is take my short piece of wire. And. I'm going to hook. It up to my positive.
What are symptoms of bad solenoid?
As a result, the common signs of a bad starter solenoid include:Engine Doesn't Crank or Start. ... No Clicking Noise When Trying to Start the Engine. ... Starter Spins Without Fully Engaging the Flywheel (Rare) ... Engine Cranks Slowly (Rare) ... Test the battery. ... Check That Power is Getting to the Starter Solenoid.More items...•
How do you know if its the starter or solenoid?
Let someone turn on the ignition key or press the starter button. Observe the light — if it doesn't turn on, the solenoid is likely failing to transfer power and might need replacement. However, if the light turns on but there's no clicking sound or starter engagement, the issue lies with the car starter.
How do you troubleshoot a solenoid?
3:598:14How to troubleshoot a solenoid valve that does not close - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell if the system conditions cannot be adjusted to ensure that the belt can close then if possibleMoreWell if the system conditions cannot be adjusted to ensure that the belt can close then if possible replace the valve with another type and or size to meet the given system conditions.
How do you test a starter solenoid with a screwdriver?
0:535:14How To Test A Car Starter With A Screwdriver And Jumper Cables!YouTubeStart of suggested clipEnd of suggested clipAnd what you want to do is you want to jump this to the s part of the small stud. Okay now once youMoreAnd what you want to do is you want to jump this to the s part of the small stud. Okay now once you do this you're activating a solenoid and a starter. And you should see the gear pop out and spin.
How do you jump a solenoid?
0:271:17How to Jump the Solenoid on your ATV or GoKart - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat we have to do is we have to move the coverings over the two bolts. This is black is negativeMoreWhat we have to do is we have to move the coverings over the two bolts. This is black is negative red is positive.
How do you test a solenoid on a golf cart with a multimeter?
Set your voltmeter to the ohms reading, and connect its probe to each one of the big terminals. Of course, the reading should be zero. Next, move the cart's switch to forward, turn it on, and accelerate slowly. Your solenoid should click.
How do you know if a solenoid is bad on a multimeter?
Sometimes you find a normal read on the digital multimeter but the coil is actually not functioning. At this time, you can use a screwdriver and put it near the armature then energize the solenoids. If there is a magnet in the presence, the coil is good. Otherwise, it is bad, and you need to change a new one.
How do you check ohms on a solenoid?
1:122:53The right way for testing any solenoid coil !! How to test ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you find three pins there one of them is a flat pin which is connected to the ground. What youMoreIf you find three pins there one of them is a flat pin which is connected to the ground. What you need to do is connect the other two pins with the multimeter step 3 read the number on the multimeter.
What happens when a solenoid fails?
A faulty starter solenoid can exhibit several symptoms, including these: Engine doesn't crank: This is a result of the starter solenoid failing to deliver power to the starter motor. No clicking sound: This can mean either a faulty starter solenoid or starter relay.
Will a bad solenoid click?
One possibility is the solenoid. A single “click” sound comes from the engine compartment or from under the car. This could mean that the solenoid is trying to engage but that the internal components are stuck and unable to work properly. Repeated “clicking” sounds usually indicate a dead battery.
Why does my golf cart click but not move?
A Club Car golf cart can start clicking but not move, due to dust accumulating inside the battery ports. Opening the battery ports and checking whether there is any dust accumulation can tell you if this is the case. Cleaning it thoroughly with a cloth can resolve the problem.
How do you troubleshoot a solenoid?
3:598:14How to troubleshoot a solenoid valve that does not close - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell if the system conditions cannot be adjusted to ensure that the belt can close then if possibleMoreWell if the system conditions cannot be adjusted to ensure that the belt can close then if possible replace the valve with another type and or size to meet the given system conditions.
How to check a solenoid?
Follow These Simple Steps to Check the Solenoid: 1. You will need a couple of tools: a voltmeter or multimeter, and (typically) a ½” wrench. 2. Disconnect any cables from the two large terminals. Be sure to wrap the cable ends in tape, and keep the ends separate from each other. 3.
What voltage is applied to the two small terminals to activate the solenoid?
Battery voltage is applied to the two small terminals to activate the solenoid, which then connects the two large terminals together. From time to time, the two large terminals malfunction and the solenoid needs to be replaced.
How to check solenoid on G9 Yamaha?
The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced. You must be careful while doing this crude test; there could be sparks when the two terminals touch.
Why is my Yamaha golf cart not moving?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid. The battery has to be checked first to see if it’s delivering the right voltage while in the idle state as well as when the pedal is pressed. There can be other reasons for the Yamaha golf cart not moving though you hear the click.
What to do if your G9 golf cart is not clicking?
If you find your G9 Yamaha golf cart not starting nor clicking, check the key components for damage. If you find the parts to in good condition, check the brushes in the starter/generator.
Why is my solenoid not clicking?
The reason why the solenoid is not clicking could be that it is faulty or has no grounding. Experts recommend checking all wiring and cable connections to rule out this possibility. Batteries on your G16 Yamaha golf carts should raise sufficient power to reach the solenoid and the starter/generator.
How to tell if golf cart solenoid is bad?
One of the most common and obvious signs of the bad solenoid is the golf cart's failure to start when you initiate the ignition process. Once you click the accelerator and turn on the ignition switch, it is supposed to send a signal to activate the solenoid and start the cart. If the cart does not start, there is a big possibility ...
What is a solenoid in golf carts?
Simply put, a solenoid is a device that can transform electrical energy into mechanical energy. It's a coil of wire which is used as an electromagnet. The solenoid has the capability of creating a magnetic field with the help of an electric current. Solenoids work as the “go switch”, which is a must for any golf cart.
Why is my golf cart not starting?
If the cart does not start, there is a big possibility of a damaged solenoid. Another reason for a bad solenoid is that the contacts are starting to get damaged due to overheating or high current passing through them. Note: You may not necessarily experience all of these issues to recognize bad solenoids on your golf cart.
Why won't my golf cart turn over?
For a gas golf cart, the most common symptom is the starter failing to engage, so the engine doesn't turn over. Starters have the responsibility of activating the flywheel. When the flywheel starts to work, the starter is supposed to disconnect.
What is a solenoid on a golf cart?
A solenoid, for our purposes, is a type of relay. A relay is a type of switch that uses a low power circuit to operate a high power circuit. A solenoid uses a magnetic coil (the actual solenoid) on a low power circuit to push a rod that closes a high power circuit. On your golf cart, this high powered circuit is either your ignition on ...
Why does my golf cart have no solenoid?
Golf cart solenoids are also typically one of the first components to fail in your golf cart, because they work very hard, turning on and off every time you stop and go in your golf cart. If you have an issue with no start or no go then your solenoid should be pretty high on your list of things to check.
What is a golf cart go switch?
On your golf cart, this high powered circuit is either your ignition on a gas golf cart or your electrical motor power circuit for an electric golf cart. Basically it’s your golf cart’s go switch, and it’s absolutely essential to your golf cart’s ability to do its job. Golf cart solenoids are also typically one of the first components ...
What happens if a solenoid reads infinity?
If it reads infinity or open lead, then the solenoid has an internal fault and requires replacement. Your solenoid should also have a range that it operates in, and if the resistance reads outside of that range, you should replace the solenoid even if it works to avoid damaging other components.
What is the most important part of a golf cart?
One of the most important components of your golf cart is the solenoid. It is one of the main components of your golf cart that allows it to move. Whether you have a Yamaha, E-Z-GO, or Club Car golf cart, and no matter if it is an electric or gas golf cart, you need a properly operating solenoid to get anywhere. Contents [ show]
What to do if your solenoid doesn't work?
Before you run out and get a solenoid, you’ll have to test the entire ignition system this way to find out what’s not working, and it is a bit of a pain.
How does an inductive throttle sensor work?
So you push the pedal down, and your inductive throttle sensor makes its first signal. This will activate the speed controller and solenoid. The way this works is a relatively low powered circuit is made with the low side of the solenoid.
How to check if a golf cart solenoid is silent?
On an electric golf cart, if the solenoid is silent – no clicking – use the setting voltmeter to DC volts using the 200 range. First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn’t move, then the problem is not with the solenoid.
Why do golf carts have solenoid?
The solenoid is simply there to allow electricity to flow freely to the controller and motor which will result in a running golf cart. RELATED: 4 Signs you need to Replace your Golf Cart Batteries.
Why is my golf cart not clicking?
On an electric golf cart, the most common symptom is the solenoid is not delivering electricity to the controller when the vehicle’s ignition is turned on. In normal operating conditions, the solenoid clicks on and off with the ignition switch. A failing solenoid will generally not click. Two things could be going on here.
What does it mean when a golf cart solenoid goes bad?
Technically, in fact, a solenoid is a shape – a shape in which the length of something coiled is longer than the diameter of the coils. In engine starters, this refers to the smaller motor ...
What does a solenoid do when you turn the ignition?
Step by step, it looks like this: When you turn the ignition key, a small amount of electricity goes to the solenoid. The solenoid uses that small amount of juice to close two heavy-duty contacts that allows a large jolt of electricity to pass through the starter. The solenoid also sends a pinion gear forward, which is the device ...
Why won't my solenoid click?
The solenoid might not be getting enough electricity to do its work – which could be caused by loose connections, a weak battery or the coil wearing out.
