how to tighten a belt on a golf cart

by Terrence Dach Published 2 years ago Updated 2 years ago

How do you resolve these issues?

Switch OFF the golf cart’s engine.
Reach to where the drive belt is located and use your fingers to press the drive belt between the two clutches.
The belt must deflect at least one and a half inches under the pressure of your fingers.
If it doesn’t yield, the drive belt is too tight. ...

Full Answer

Can a drive belt be too tight on a golf cart?

Feb 28, 2020 · Tightening a starter belt on an EZGO GOLFCART. You will need a 9/16 wrench...

How do you check the drive belt on a golf cart?

To check if the drive belt is too tight, follow these steps: Switch OFF the golf cart’s engine. Reach to where the drive belt is located and use your fingers to press the drive belt between the two …

How do I know if my drive belt is too tight?

May 19, 2021 · Quick and easy way to tightened your start v-belt on your Golf Cart.

How to replace a clutch on a golf cart?

How Tight Should a Golf Cart Drive Belt Be? The drive belt should not be too tight. If it’s too tight it can risk wearing off faster and it’s also harder to shift gears. To check if your drive belt is set …

Can you tighten a belt on a golf cart?

And EZGO is no different – there are no screws, knobs, or any other type of adjustment item that you can use to tighten up your belt. Once the belt is one, it has the same tightness and can only be changed if you swap the belt for another one either the proper length and width for your specific cart engine.

How do you tighten a clutch belt on a Club Car golf cart?

Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.Sep 19, 2011

How do you tighten the belt on a Yamaha gas golf cart?

Part of a video titled How to tighten a loose Starter Belt on Yamaha Golf Cart YDRA. G29

0:00

2:03

And wiggle this belt here yeah she's loose. All right my 12 mil uh socket here grab that loosen thatMoreAnd wiggle this belt here yeah she's loose. All right my 12 mil uh socket here grab that loosen that up 17 mil wrench here wrap this down. There you go.

How do you put a belt on a EZ Go golf cart?

Part of a video titled Changing the Drive Belt and Starter Generator Belt 2008 EZGO TXT

2:47

5:57

Just. First put the belts on and then tilt the starter generator as far as you can and tighten thatMoreJust. First put the belts on and then tilt the starter generator as far as you can and tighten that nut up. By hand first and then use the wrench to get it a little bit. Tighter.

How does the clutch work on a golf cart?

Both golf cart clutches look similar to a large pulley but each clutch has a sliding sheave that moves in & out along a central shaft as the clutch spins. The other sheave is fixed to either the crankshaft or the differential input shaft and it does not slide, it just spins.Apr 4, 2012

How do you remove the drive belt from a club car?

First, raise the golf cart engine cover to access the drive belt inside the engine compartment. It should be visible and easily identifiable. Next, loosen the drive belt tension bolt with an open-end wrench on the front pulley. Slide the old drive belt off the front and then the rear clutch pulley.

How do you change the drive belt on a 2018 Yamaha Golf Cart?

Part of a video titled Yamaha Drive Belt | How to Install on G29 Golf Cart - YouTube

0:46

2:46

Now to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it overMoreNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it over the top of this outer chief like this just slowly roll it over. And. It will come right.

How do I find the model number of my Yamaha Golf Cart?

To find out the model and year of your Yamaha Golf Cart the first thing you will need is to find your cart's SERIAL NUMBER.

Under the seat where the floor board meets the motor compartment.
Under the rear bumper on the frame.
Under driver side glove box.

How do you know if your golf cart clutch is bad?

What Kinds of Problems Can a Golf Cart Clutch Have?

A sudden inability to maintain even slow speeds when heading uphill or changing elevation.
Slowing down to a crawl, then speeding up, then slowing again, seemingly without reason.
Jolting during startup.
A 'cranking' sound when starting up the golf cart.

May 11, 2017

How do you change a starter belt on a EZ Go golf cart?

Part of a video titled ezgo starter generator belt replacement - YouTube

6:08

7:05

It. Simply go over the driven pull or the drive pulley. Walk it over the drive driven pulley.MoreIt. Simply go over the driven pull or the drive pulley. Walk it over the drive driven pulley.

How do you measure a torque converter belt?

Simply take a measuring tape and hold it against the outer plate of the pulley. Measure from one side of the plate to the opposite side. If you're running a standard torque converter the diameter will either be 6-inches, 7-inches, 7.5-inches or 8.5-inches.

What happens if a golf cart belt is too tight?

If the belt is too tight then your starter will be under strain and this should be avoided. The best test to see if a golf cart drive belt has the correct tension is to use the Finger Test.

How to tell if golf cart drive belt is damaged?

Make sure that the golf cart’s engine is turned OFF. An inspection can reveal if the drive belt is damaged. Check if it is too tight or loose. In case of a damaged, tight, or loose belt order a new one. Replacing the drive belt is not a very difficult task.

What is slipping drive belt on 1985 golf cart?

The 1985 Club Car golf cart is no exception to this. The way the clutches are designed for these golf carts is that there is the drive belt connecting the two, the driven and the drive clutches. It has to be of the appropriate size and tension for it to provide a smooth ride.

Why is my club car belt loose?

The drive belt on your Club Car golf cart may be loose if the belt you have fitted is too large for the golf cart. Some belts can overheat with overuse, or even stretch after a few months and become too loose.

How to remove drive belt?

Removing the drive belt involves holding the belt with both hands in the center between the driven and drive clutches and lifting the belt. You must now rotate the driven clutch counter-clockwise and slip the belt off the sheave. You can then slide the drive belt off the drive clutch.

Why is my club car drive belt so tight?

The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches. It should not be less as well.

Why does my golf cart drive belt slip?

The reason for the drive belt slipping could be that it is of a larger/longer size and therefore loose. You may start feeling the slippage after driving for a while. This is because the belt gets heated up after the golf cart runs for some time and loosens further .

How to tell if golf cart drive belt is too tight?

To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.

What is the belt on a golf cart?

The drive belt on a golf cart connects the two clutches (the drive clutch and the driven clutch) and distributes the power from the engine to the rear wheels.

Why is my Ezgo golf cart belt so loose?

The reason your EZGO drive belt is too loose could be because it’s worn out, or you’re simply using the wrong size drive belt. In this case, need to find a replacement immediately. A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform.

Why is my EZGO belt so tight?

The reason your EZGO drive belt is too tight can be because you’re not using the right size drive belt.

Why is my clutch too tight?

It can also be too tight because the drive/driven clutch is misplaced or broken. A drive belt that’s too tight can damage the drive and driven clutches and can also result in the drive belt being worn out too fast. To check, whether the drive/driven clutch is misplaced or broken call a certified technician to have a look.

What does it mean when the drive belt is misaligned?

Check and see if the drive belt appears misaligned? If so, is it misaligned more towards the driven clutch (the one on the axle) or the drive clutch (the one on the motor)? If it’s misaligned there is something wrong with the drive clutch.

How to stop a EZYGO drive belt from slipping?

How to stop a EZYGO drive belt slipping: Make sure that you have the right drive belt. Sometimes the wrong drive belt will not be as wide as the clutch you are putting it on. This gives it an unwanted room to move back and forth when you are using the golf cart.

Golf-FAQ.com