To adjust, loosen the 10 mm locking nut (older models will have 8mm locking nuts) on the adjuster screw, then ever so slightly, turn the adjuster screw (clockwise to tighten) till there is a “slight drag” on the feeler gauge. While pushing down on the screwdriver, tighten the jam nut and check with the feeler gauge for proper clearance.
Full Answer
Does the belt on a Yamaha G14 G16 roll and squeal?
We have replaced the belt on a Yamaha G14 G16 golf cart but it still squeals when going up a hill, and won't hardly pull. Does anyone know how to do a adjustment for the belt to work correctly? Does it roll easy, not like the brakes are dragging a bit. Yes, it seems to roll ok.
What kind of engine does a Yamaha golf cart have?
Initially, the Yamaha G1 2-cycle gas was the standard-bearer and in 1985 the G2 4-cycle single-cylinder gas engine was introduced as the new standard. link to How Does A Golf Cart Work? - Complete Guide To Understanding It (2021)
Why won't my golf cart shift?
Well if the belt fits right then the problem could be the drive clutch, i would lift the back of the cart off the ground and run it, watch to see how and where the belt rides in the clutches and how they shift. You must log in or register to reply here.
How tight should a starter belt be on a golf cart?
The drive belt should not be too tight. If it's too tight it can risk wearing off faster and it's also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger.
How do you tighten a golf cart belt?
There is no provision for adjusting the drive belt on a Club Car golf cart. If you find the belt loose or too tight, you have to go for a replacement belt.
How do you change a starter belt on a Yamaha golf cart?
0:435:12Yamaha G2, G9 Drive and Starter Belt Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just rolling it right over. It's that simple that was a little twisting a little tugging. ThatMoreAnd just rolling it right over. It's that simple that was a little twisting a little tugging. That will come right on. Now. We do this lift it from around the clutch.
How loose should the drive belt be on a Yamaha golf cart?
0:012:00How to Check the Belts in your Gas Golf Cart | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipDown below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.
How do I stop my golf cart belt from squeaking?
Your belt may also be wearing down and even fraying which is a problem that can cause the belt to both squeak and whine as it runs. Replace any frayed belts right away, before they break, to avoid damaging your engine, and lubricate or replace any pulleys which continue to squeak on your cart.
Can you adjust a golf cart clutch?
If you are unsure about removing the drive belt or the clutch, then you can adjust it. Just take out the belt and wound it again with the secondary clutch according to the requirements, and your problem should be fixed.
How do you remove a starter from a Yamaha golf cart?
How to Remove, Wire & Test a Golf Cart Starter Generator Disconnect the negative battery cable. Loosen and then remove the top and bottom bolts of your starter generator. Remove the belt of your starter generator and leave it around the engine. Loosen all of the wiring and remove them each by hand.More items...
How does a drive belt work on a golf cart?
The drive belt is one of the most important belts on your EZGO golf cart. It helps to translate engine power into different gears and makes it possible to shift your cart, giving it the get up and go it needs to run. However, there are times when this belt may be loose or damaged and you may want to tighten it.
How does a golf cart starter generator work?
The starter generator works in two ways; the starter portion cranks the engine and the generator portion recharges the battery. When the gas pedal is depressed the starter cranks the engine over. When it begins to run on its own, the generator portion of the unit begins to charge the 12-volt battery.
How do you put a drive belt on a Yamaha golf cart?
0:152:32HOW TO CHANGE A DRIVE BELT ON YAMAHA GOLF CART ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spinMoreJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spin the back off.
How do you change a drive belt on a 2007 Yamaha golf cart?
0:462:46Yamaha Drive Belt | How to Install on G29 Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it overMoreNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it over the top of this outer chief like this just slowly roll it over. And. It will come right.
How to remove gas filler hatch?
Put the vehicle in neutral and open the seat cowling pulling up on the lever in the gas filler hatch. Remove the 5 screws from the front and rear of the cowling and lift out.
What is a golf cart?
Golf carts are also known as golf cars. The term "cart", in its purest sense, refers to a vehicle that does not travel under its own power. Golf cars, however, are most commonly referred to as golf... link to Club Car DS Wiring Diagrams 1981 To 2002.
How to remove spark plug from engine?
Locate the spark plug (s) on the top of the engine and remove the cable, exposing the top of the plug. Use a spark plug socket (13/16″) and ratchet to remove the spark plug and inspect the ceramic insulator.
Does the G21 have a filter?
The G2, G9, G11, and the G21 model Fuel tank has a screw-in filter that is difficult to reach. It is advisable to remove the 2-4 bolts holding the tank in and pull the tank out to drain and replace the filter. Please note that on ALL models using the screw-in filter the tank will need to be drained.