How do you resolve these issues?
- Switch OFF the golf cart’s engine.
- Reach to where the drive belt is located and use your fingers to press the drive belt between the two clutches.
- The belt must deflect at least one and a half inches under the pressure of your fingers.
- If it doesn’t yield, the drive belt is too tight. ...
How to change drive belt on a club car golf cart?
How to Change the Drive Belt on a Club Car Golf Cart Switch the engine OFF after parking the golf cart.. Allow the engine to cool, if it has been running for some time.. Remove the engine cover.. You will be able to see the drive belt now.. Use an open-end wrench to loosen the drive belt tension ...
Why is my club car drive belt too tight?
The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches. It should not be less as well.
How do I know if my golf cart drive belt is bad?
The best test to see if a golf cart drive belt has the correct tension is to use the Finger Test. Press the drive belt with one finger at its center between the two clutches. It should sag by just an inch and a half. Another method suggested by an expert is to go for a drive belt that is 1-inch shorter than the stock belt in your cart.
What does a drive belt do on a club car precedent?
The drive belt on a Club Car Precedent golf cart is an important component and using the right-sized drive belt is essential for a smooth ride. To primary function of a golf cart drive belt is to connect the primary clutch and the secondary clutch.
How do you tighten a belt on a Club Car?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
How do I know if my golf cart belt is too loose?
You might notice some squealing, or find it a bit hard to shift gears when you've inserted a new belt, give it some time to “break-in”. If your drive belt is too tight it will wear out faster and might cause some damage to the clutch, if it's too loose, it will underperform and decrease the speed of the golf cart.
How do you put torque in a golf cart?
3:4917:29Plum Quick Rhino Torque Motor Install & Review - YouTubeYouTubeStart of suggested clipEnd of suggested clipParts of the stud. Of both sides. And you're going to need two to go on the top portion of the studsMoreParts of the stud. Of both sides. And you're going to need two to go on the top portion of the studs. For the mounting nut. Now what i've done here is i've taken some old wrenches.
How do you put a drive belt on a golf cart?
0:445:12Yamaha G2, G9 Drive and Starter Belt Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just rolling it right over. It's that simple that was a little twisting a little tugging. ThatMoreAnd just rolling it right over. It's that simple that was a little twisting a little tugging. That will come right on. Now. We do this lift it from around the clutch.
Can you tighten a golf cart drive belt?
You may have to remove the cover and watch the clutches in action while the cart is in motion to make sure that it is indeed the drive belt that is slipping. You will have to change the drive belt as there is no other alternative to it. You can't make any adjustments or tighten the belt.
Can you tighten a belt on a golf cart?
And EZGO is no different – there are no screws, knobs, or any other type of adjustment item that you can use to tighten up your belt. Once the belt is one, it has the same tightness and can only be changed if you swap the belt for another one either the proper length and width for your specific cart engine.
How can I speed up my Club Car golf cart?
0:061:31Club Car Precedent Speed Increase SUPER EASY!!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. AndMoreIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. And if you turn it that way or clockwise it speeds things up. Very.
Why is my golf cart slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How much torque does a 48 volt golf cart have?
High torque series. 48 volt (11.4 horse power at 2300 rpm) or 36 volt (8 horse power at 1600rpm) Requires a minimum 400 amp controller upgrade, 4 guage cables, heavy duty forward/reverse switch and solenoid.
How to change the belt on a golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
Where is the drive belt on a golf cart?
Raise the golf cart engine cover, to access the drive belt inside the engine compartment. The drive belt is plainly visible.
Why is my club car not engaging?
Over time, such belts can become dry and cracked, or may even break. If the cart is having trouble accelerating or will not engage at all, it may be because the belt needs changing.
How to tell if golf cart drive belt is too tight?
To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.
What is the belt on a golf cart?
The drive belt on a golf cart connects the two clutches (the drive clutch and the driven clutch) and distributes the power from the engine to the rear wheels.
Why is my Ezgo golf cart belt so loose?
The reason your EZGO drive belt is too loose could be because it’s worn out, or you’re simply using the wrong size drive belt. In this case, need to find a replacement immediately. A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform.
Why is my EZGO belt so tight?
The reason your EZGO drive belt is too tight can be because you’re not using the right size drive belt.
Why is my clutch too tight?
It can also be too tight because the drive/driven clutch is misplaced or broken. A drive belt that’s too tight can damage the drive and driven clutches and can also result in the drive belt being worn out too fast. To check, whether the drive/driven clutch is misplaced or broken call a certified technician to have a look.
What does it mean when the drive belt is misaligned?
Check and see if the drive belt appears misaligned? If so, is it misaligned more towards the driven clutch (the one on the axle) or the drive clutch (the one on the motor)? If it’s misaligned there is something wrong with the drive clutch.
How to stop a EZYGO drive belt from slipping?
How to stop a EZYGO drive belt slipping: Make sure that you have the right drive belt. Sometimes the wrong drive belt will not be as wide as the clutch you are putting it on. This gives it an unwanted room to move back and forth when you are using the golf cart.
How to change drive belt on golf cart?
The drive belt is plainly visible. Loosen the drive belt tension bolt, with the open end wrench, on the front pulley. Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley.
How to find the governor on a golf cart?
Locate the golf cart's governor; you can find the governor by tracing the thickest cable running from the gas pedal. This cable runs through the governor on its way to the carburetor. Use a screwdriver—or in some cases a wrench—to loosen the tension on the governor's springs.
How much slack should a belt have?
Typical belt should have about 1.5" slack when you push down on the top in center of clutches.
What is a timing belt?
A timing belt, timing chain, or cambelt is a part of an internal combustion engine that synchronizes the rotation of the crankshaft and the camshaft (s) so that the engine's valves open and close at the proper times during each cylinder's intake and exhaust strokes. A timing chain is a roller chain.
