How do you resolve these issues?
- Switch OFF the golf cart’s engine.
- Reach to where the drive belt is located and use your fingers to press the drive belt between the two clutches.
- The belt must deflect at least one and a half inches under the pressure of your fingers.
- If it doesn’t yield, the drive belt is too tight. ...
Full Answer
How to properly drive a golf cart?
To check if the drive belt is too tight, follow these steps: Switch OFF the golf cart’s engine. Reach to where the drive belt is located and use your fingers to press the drive belt between the two clutches. The belt must deflect at least one and a half inches under the pressure of …
How to change drive belt on EZGO golf cart?
· Quick and easy way to tightened your start v-belt on your Golf Cart.
How to adjust the drive belt?
Does my golf cart need seat belts?
Can you tighten a golf cart drive belt?
And EZGO is no different – there are no screws, knobs, or any other type of adjustment item that you can use to tighten up your belt. Once the belt is one, it has the same tightness and can only be changed if you swap the belt for another one either the proper length and width for your specific cart engine.
How do you tighten a clutch belt on a Club Car golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
How do I adjust my drive belt?
0:592:19How To Check & Adjust Serpentine Drive Belt Tension On Your CarYouTubeStart of suggested clipEnd of suggested clipThe automatic drive belt tensioner. Cannot be adjusted. So if you find that your drive belt is tooMoreThe automatic drive belt tensioner. Cannot be adjusted. So if you find that your drive belt is too tight or too loose.
How do you tighten the belt on a Yamaha gas golf cart?
0:002:03How to tighten a loose Starter Belt on Yamaha Golf Cart YDRA. G29YouTubeStart of suggested clipEnd of suggested clipAnd wiggle this belt here yeah she's loose. All right my 12 mil uh socket here grab that loosen thatMoreAnd wiggle this belt here yeah she's loose. All right my 12 mil uh socket here grab that loosen that up 17 mil wrench here wrap this down. There you go.
How do I know if my golf cart clutch is bad?
What Kinds of Problems Can a Golf Cart Clutch Have?A sudden inability to maintain even slow speeds when heading uphill or changing elevation.Slowing down to a crawl, then speeding up, then slowing again, seemingly without reason.Jolting during startup.A 'cranking' sound when starting up the golf cart.
How do I know if my golf cart belt is bad?
0:152:00How to Check the Belts in your Gas Golf Cart | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipDown below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.
How do you tighten a tensioner pulley?
Turn the adjustment bolt on the side, top or bottom of the pulley counterclockwise with the ratchet and socket until the accessory belt is loose enough to remove. Tighten the tensioner pulley by turning the adjustment bolt clockwise with the ratchet and socket until the belt is tight.
Can you tighten an automatic belt tensioner?
Locate the adjuster bolt on the belt tensioner used to secure the serpentine belt, and adjust the tension by loosening or tightening the adjuster bolt with a racthet and socket while you simultaneously move the belt back and forth gently to find the proper tension.
Can you over tighten a belt tensioner?
Over-tightened belts can cause internal damage to the bearings inside the pulleys. It can also cause overheating of the belts and premature wear. Put the vehicle back together by replacing the components required to access the belt tensioners. To test, operate the vehicle for several minutes and shut it off.
How do you change the drive belt on a 2018 Yamaha Golf Cart?
0:462:46Yamaha Drive Belt | How to Install on G29 Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it overMoreNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it over the top of this outer chief like this just slowly roll it over. And. It will come right.Yamaha Drive Belt | How to Install on G29 Golf Cart - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you change the drive belt on a 2018 Yamaha Golf Cart?
How do you measure golf cart belts?
0:002:04How to measure for a go-kart drive belt. - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover. Now the first measurement we're going to take on this is we're going to measure from theMoreCover. Now the first measurement we're going to take on this is we're going to measure from the centerline of the crankshaft. To the centerline of the jack shaft.How to measure for a go-kart drive belt. - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you measure golf cart belts?
How do I know if my drive belt is aligned?
1:093:44Using a Laser Alignment Tool to Check Pulley Alignment - YouTubeYouTubeStart of suggested clipEnd of suggested clipSecond turn on the laser. And place the tool base into the pulley grooves closest to you that is theMoreSecond turn on the laser. And place the tool base into the pulley grooves closest to you that is the pulley grooves that are the farthest away from the engine or the accessory.
How do you align and tension belts?
Drive Belt Tension & Alignment AdjustmentSwitch the input power OFF and unplug. the power cord.Remove the front hood.Verify the drive belt alignment. Make sure that the drive belt is aligned parallel to the frame rail. Measure the belt to frame rail distance at the drive roller pulley and at the drive motor pulley.
What is the belt on a golf cart?
The drive belt on a golf cart connects the two clutches (the drive clutch and the driven clutch) and distributes the power from the engine to the rear wheels.
What to do if your drive belt is too loose?
The best course of action if your drive belt is too loose is to get a new drive belt.
Why is my clutch too tight?
It can also be too tight because the drive/driven clutch is misplaced or broken. A drive belt that’s too tight can damage the drive and driven clutches and can also result in the drive belt being worn out too fast. To check, whether the drive/driven clutch is misplaced or broken call a certified technician to have a look.
Why is my EZGO belt so tight?
The reason your EZGO drive belt is too tight can be because you’re not using the right size drive belt.
What to do if your clutch is not working?
Once you’ve confirmed that the drive clutch is not functioning properly you either need to have it fixed or replace. Call a trusted certified technician to have it fixed or replaced for you.
What does it mean when the drive belt is misaligned?
Check and see if the drive belt appears misaligned? If so, is it misaligned more towards the driven clutch (the one on the axle) or the drive clutch (the one on the motor)? If it’s misaligned there is something wrong with the drive clutch.
How to stop a EZYGO drive belt from slipping?
How to stop a EZYGO drive belt slipping: Make sure that you have the right drive belt. Sometimes the wrong drive belt will not be as wide as the clutch you are putting it on. This gives it an unwanted room to move back and forth when you are using the golf cart.
