How do you tighten the drive belt on a golf cart?
Switch OFF the golf cart’s engine. Reach to where the drive belt is located and use your fingers to press the drive belt between the two clutches. The belt must deflect at least one and a half inches under the pressure of your fingers. If it doesn’t yield, the drive belt is too tight.
Why is the drive belt on my club car golf cart loose?
The drive belt on your Club Car golf cart may be loose if the belt you have fitted is too large for the golf cart. Some belts can overheat with overuse, or even stretch after a few months and become too loose. You need to make sure to order the right size and insist on using heavy duty drive belts because they will last longer.
What happens if the drive belt is too tight?
It can also be too tight because the drive/driven clutch is misplaced or broken. A drive belt that’s too tight can damage the drive and driven clutches and can also result in the drive belt being worn out too fast. To check, whether the drive/driven clutch is misplaced or broken call a certified technician to have a look.
How to replace a clutch on a golf cart?
Switch OFF the golf cart’s engine. Take a screwdriver and gently insert it between the belt’s bottom and the clutch’s groove. Slowly rotate the clutch and the belt will come off easily. If the belt is already loose, taking it out is very easy.
How do you tighten the belt on a Yamaha golf cart?
2:465:12Yamaha G2, G9 Drive and Starter Belt Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll put it between stir generator and the block of the engine you do not press hard just a littleMoreYou'll put it between stir generator and the block of the engine you do not press hard just a little taunt. Then we'll tighten the 12 millimeter bolt I just will go.
How do you tighten a belt on a gas golf cart?
There is no provision for adjusting the drive belt on a Club Car golf cart. If you find the belt loose or too tight, you have to go for a replacement belt.
How do you put a drive belt on a Yamaha golf cart?
0:152:32HOW TO CHANGE A DRIVE BELT ON YAMAHA GOLF CART ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spinMoreJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spin the back off.
How tight should a golf cart belt be?
The drive belt should not be too tight. If it's too tight it can risk wearing off faster and it's also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger.
Can you adjust a golf cart clutch?
If you are unsure about removing the drive belt or the clutch, then you can adjust it. Just take out the belt and wound it again with the secondary clutch according to the requirements, and your problem should be fixed.
How do I stop my golf cart belt from squeaking?
Your belt may also be wearing down and even fraying which is a problem that can cause the belt to both squeak and whine as it runs. Replace any frayed belts right away, before they break, to avoid damaging your engine, and lubricate or replace any pulleys which continue to squeak on your cart.
How does a drive belt work on a golf cart?
The drive belt is one of the most important belts on your EZGO golf cart. It helps to translate engine power into different gears and makes it possible to shift your cart, giving it the get up and go it needs to run. However, there are times when this belt may be loose or damaged and you may want to tighten it.
How do you tighten the belt on a Club Car golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
What is a drive belt in a golf cart?
The golf cart drive belt is the larger (1" to 1 3/16" wide), longer and usually looser belt on gas golf cars. It connects the drive clutch (on the engine) to the driven clutch (on the differential) and transfers the power of the engine to the rear wheels.
How do you measure a golf cart belt?
0:356:35Cushman Golf cart Pt.6 CVT belt - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe it's right on the rear end uh you need the outside diameter of that then you need the center toMoreThe it's right on the rear end uh you need the outside diameter of that then you need the center to center measurement. Between the center of the driven pull or drive point and the driven pulley.
Do golf carts have transmissions?
All golf carts (much like cars) have a clutch, which is the part of the drivetrain that helps the put the power of the motor down through to the wheels/ground. Golf cart clutches are a part of the Continuously Variable Transmission (or CVT).
Are golf carts belt driven?
Belts - Drive Belts The drive belt on your club car golf cart is the one that is loose between both your drive and driven clutch. A worn out belt will slip and not allow your carts engine to power your rear wheels. Replacing your belt will give your golf car a smoother take off and increase the torque as well as speed.