Most clubmakers use a shaft cutter–the same as a small pipe cutter a plumber would use. This cuts a small groove in the shaft slightly deeper each circle around the shaft until it cuts through. Some clubmakers might use a grinding wheel equipped with a saw blade to cut the shaft cleanly.
How do you cut a golf shaft?
Most clubmakers use a shaft cutter–the same as a small pipe cutter a plumber would use. This cuts a small groove in the shaft slightly deeper each circle around the shaft until it cuts through. Some clubmakers might use a grinding wheel equipped with a saw blade to cut the shaft cleanly.
How do you fix a bent shaft on a golf club?
Remove the existing grip. With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft. And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club.
What end of the shaft do you cut on a club?
The butt end of the shaft is grip end. If you are shortening or extending the length of a golf club, this is where you will cut. If you want to change the play-ability of the club (feel, flex to a certain extent, spin rate, dispersion), you will be cutting the tip end of the shaft.
Do I need to trim the tip of my Shaft?
Parallel tip shafts (where the shaft remains a constant diameter from the tip up a specified distance up the tip) will most often require some tip trimming. This is required to offset the increasing heads weights as the clubs become shorter and maintain the flex the manufacturer designed into the shaft for a finished club.
How do you cut carbon golf shafts?
With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft. And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club.
How do you trim a golf shaft?
0:253:03Golf Tips : How to Trim Golf Club Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipGood measuring stick a marking pin will need a chop saw that we can chop with and we'll also need aMoreGood measuring stick a marking pin will need a chop saw that we can chop with and we'll also need a grinder just to trim off the burner off the end of it before the club is reesh aft.
Can you cut a graphite golf shaft with a hacksaw?
Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops.
Can I use a pipe cutter on graphite shaft?
0:002:12HOW NOT TO CUT GRAPHITE GOLF SHAFTS / Wrong Tool for the JobYouTubeStart of suggested clipEnd of suggested clipSo i've had a few different people ask me can i use the pipe cutter that we used in the steelMoreSo i've had a few different people ask me can i use the pipe cutter that we used in the steel shafted assembly video on graphite. And the answer is emphatically no and i'm going to show you real quick
What happens when you butt trim a shaft?
1:363:54How Does Butt Trimming a Golf Shaft Affect Playability? - YouTubeYouTubeStart of suggested clipEnd of suggested clipChange when cutting one inch or less or or more off of the butt end probably. The biggest downsideMoreChange when cutting one inch or less or or more off of the butt end probably. The biggest downside of cutting. Or making a closed shoulder is the effect that it has on swing weight.
Can I shorten my driver shaft?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
How do you cut a graphite shaft at home?
1:2914:05Golf Club Repair - How To cut a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you're gonna if this is going to be your primary cutting tool don't skimp alright I'm a big toolMoreIf you're gonna if this is going to be your primary cutting tool don't skimp alright I'm a big tool nut don't skimp even if it's a hand tool.
Does shortening a golf shaft make it stiffer?
Shaft tipping is when a club builder removes length from the tip section of a shaft, which is the end where the clubhead is installed. In most cases, tip trimming a shaft makes it meaningfully stiffer. It also increases torsional stiffness, known as “torque,” which is a shaft's resistance to twisting.
How do you cut graphite?
Most people like to use a hack saw with a blade that can cut graphite. Many golf club part manufacturers will sell blades like this, and they are usually easy to install on your current hack saw. A typical hack saw blade is probably not going to do the trick. Many people also use a Dremel-type tool.
How much does it cost to cut a golf shaft?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
How do you cut a driver shaft at home?
1:144:01How to Cut Golf Shaft DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo for the first step you have to remove your old grip. I find the easiest way to do this is toMoreSo for the first step you have to remove your old grip. I find the easiest way to do this is to literally just cut a line all the way down your club.
Where do you cut golf club shafts?
The butt end of the shaft is grip end. If you are shortening or extending the length of a golf club, this is where you will cut. If you want to change the play-ability of the club (feel, flex to a certain extent, spin rate, dispersion), you will be cutting the tip end of the shaft.
Why trim a shaft?
Why trim or cut a shaft at all? When the manufacturers make a shaft, they do so in mind that is could be used for a wide number of golfers and applications, so the manufacturer makes the shaft longer than it will most likely be used in the final golf club. The number one reason for making the shaft longer is to accommodate taller players so they ...
Why do you need to trim a parallel shaft?
This is required to offset the increasing heads weights as the clubs become shorter and maintain the flex the manufacturer designed into the shaft for a finished club.
What is a combination flex shaft?
These "combination flex" shafts are designed to reduce inventory by being able to create multiple flexes from a single shaft rather than produce two different shafts. Here are the most common ones below.
What does a trimming chart show?
It is also important to understand the trimming charts show how much (if any) to take off the tip end (the skinny part or where the head will be attached). The trimming charts will not tell you an amount to take off the butt end (the fat part where the grip is installed).
What does cutting the shaft shorter do to a golf club?
The swing weight, or weight at the head of the club and any additional weighting inside the shaft, is still in place, and cutting the shaft shorter changes the balance of the club as well.
How much should a golf shaft be tipped?
Many pros have their shafts tipped as much as one or two inches. The idea behind tipping is to make the clubhead end of the shaft stiffer and even lower torque than it was designed to be to minimize twisting of the club at impact.
Why do tour pros have their shafts tipped?
Tour pros often have their shafts "tipped," or cut back from the clubhead end slightly to make the tip of the shaft stiffer. This enables them to keep the same length club but have a slightly stiffer shaft near the ball. Cutting a club from the butt end will have somewhat the opposite effect, making the shaft stiffer overall but shorter as well.
How does changing the length of a golf club affect the swing?
Changing swing characteristics: Changing the length of a golf club can moderately or severely change the swing characteristics of the club. Removing length from the butt end of the shaft also removes weight from that end and changes the swing weight and balance of the club. Cutting a shaft from one end or the other also changes the kickpoint ...
How to adjust length of golf club?
Step 1. From the butt: The easiest and quickest way to adjust the length of a club is to remove the grip and cut a given amount of the shaft off the butt end. Traditionally, this is how many youngsters get their first sets of golf clubs. Their parents cut the clubs down so they are easier for them to handle. Keep in mind, though, that cutting the ...
Is a shorter shaft stiffer than a longer shaft?
A shorter shaft is typically stiffer than a longer one. Although a shorter golf club shaft tends to be firmer than a longer one, it is important to understand the changes trimming a shaft will make to a club before making such a permanent change.
Can you cut a shaft from the butt end?
Cutting a shaft from one end or the other also changes the kickpoint of the shaft–lowering it if you cut from the butt end or raising it if you cut from the tip. Even a small adjustment to a putter can cause a significant change in feel. Keep these changes in mind when planning any changes to your club.
Series Navigation
I know this might seem obvious, but be sure to measure and mark off the point at which you are cutting. Especially while tipping a shaft (you can’t undo this), it is important to have precise measurements. Use a sharpie to make your marks on the shaft. Here is a tutorial on how to measure golf clubs.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
Why use masking tape on graphite shafts?
Secondly, by wrapping tape around the shaft, reduces the likelihood that the shaft would splinter during the last moment of the cutting process.
Can a rod saw blade cut steel?
It makes thin straight cuts in all types of shaft materials used in golf. Yes, it is even strong enough to cut steel.
Can a hacksaw cut steel?
Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops. How To Tips. I would like to share a few how-to tips as well.
Can you cut graphite shafts?
Graphite shafts need special care to be cut properly. A tubing cutter, that you would use to manually cut a steel golf shaft, will crack or destroy a graphite shaft in no time at all. Don’t think about pulling the hacksaw from your tool chest either.
Feedback
Hey guys. I want to cut a half inch off my driver shaft. I've done a lot of searching but am not finding a definitive answer. I know you need to wrap the area you're cutting in masking tape but what's not clear to me is the correct type of blade to use. Some say hacksaw, others say a chop saw (which I have to admit, I have no idea what that is).
Feedback
i've used a dremel -- or a chop saw. either work fine. hacksaws COULD splinter the ends --not sure if it's 100% true but, i'd rather not risk it.
Feedback
I used a miter box and hacksaw with a blade with the highest number of teeth per inch (TPI) I could find at the hardware store. Came out just fine.
Feedback
What is a chop saw? I have a dremel but what attachment should be used? Also, if using a dremel, how do you get the cut perfectly straight?
Feedback
I'll use anything that has fine sharp teeth. I've done most of my shafts by hand recently because I have limited space and its easier without needing electricity and cords.
Feedback
Dremel cutoff wheel. They use a similar abrasive material circular saw blade as a chop saws uses (which is what you will find at a club maker for cutting graphite shafts). I use it for my graphite shafts as well as my carbon fiber arrows for my compound bow. Never had problems with either.
Feedback
Chop saw is best, Dremel with cutoff wheel will work (but it is tough to make an even cut), and if you use a hacksaw get a 'grit' blade.
Step 1: Prepare tools
Preparing your tools is the first step but will contribute to your success. If you prepare incorrectly or lack the tools, it will take time in the process.
Step 2: Measure and mark
Measuring and marking will help you know exactly where to cut and make them more specific. It is impossible to guarantee that you will be satisfied with the first measurement results.
Step 3: Prepare to cut
After you have determined the point you want to cut, do not rush to pick up the knife to cut it. It would help if you prepared a little more to make the cutting process more convenient and safe for yourself.
Step 4: Cut a graphite golf shaft
After a complicated preparation process, now you have come to the most critical step: cut a graphite golf shaft. However, you do not need to worry too much if you have carefully prepared the above steps.
Step 5: Check the cut
The process of cutting a graphite golf shaft is almost complete. Now you just need to double-check that the cut is exactly what you want, and you can use it.
