Use a screwdriver to locate and expose the motor. It may have a small red reset button near the main power supply. Press this button and reassemble your cart. Connect the golf cart to the charger unit and recharge the batteries.
Full Answer
How to check the electric motor on an EZ-GO golf cart?
There is an easy method to check the electric motor on any EZ-Go golf cart. Go to the back of the golf cart and find the panel that covers the electric motor. Four or six screws will hold the panel in place. Use the screwdriver to remove all the screws, turning them counterclockwise and putting them in a secure location after removal.
Why is the tow run switch on my EZGO cart not working?
The tow run switch is damaged. Many times, the speed controllers of an EZGO cart are damaged or broken. These speed controllers are located under the EZGO cart seat. Check the speed controller’s attachment near the carburetor. Reach the engine area of the cart by lifting the cart seat. Locate the speed controller on the engine.
How to troubleshoot the controller of an EZGO?
Follow these steps to troubleshoot the controller of an EZGO: When the cart is to be serviced or the controller needs troubleshooting, the maintenance switch under the seat needs to be flipped. Flip the switch and turn the tow maintenance mode on. Now, take the negative battery cable (black) and disconnect it.
How to remove speed sensor from EZGO TXT PDS golf cart?
The speed sensor of an EZGO TXT PDS golf cart can be removed easily by following a few simple steps as given below. Locate the speed sensor on the golf cart. This is usually present behind the rear tire of the golf cart on the driver’s side. Remove the snap ring or circlip with two clips that hold the speed sensor in place, using a pair of pliers.
How do you test a EZ Go golf cart motor?
0:251:28Testing an electric golf cart motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipNegative 2 a1. And there we have it one wheel peel. But it's working brakes might be a little stickyMoreNegative 2 a1. And there we have it one wheel peel. But it's working brakes might be a little sticky on that side.
How do I know if my golf cart motor is bad?
You have enough going on in your life without your golf car refusing to start when you turn the key in the ignition. If your golf car won't start, is slower than it used to be, or is experiencing other technical problems, you could have a bad motor on your hands.
Where is the reset button on a ezgo golf cart motor?
Locate the motor Remove the panel so the electric motor is visible. Electric motors usually include reset buttons that can perform similar to circuit breakers. Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
How do you troubleshoot an EZ Go golf cart?
Things to Keep in Mind Before TroubleshootingEZGO golf cart batteries aren't perfect right away.Sticky accelerators are perfectly normal and can be fixed easily.Keep your cart stable.Make sure your charging wall socket isn't faulty.Keep your tire pressure stable.Troubleshooting the speed controller.
How do you test a golf cart motor?
4:0210:28Testing 36 volt golf cart motor with 12 volt battery - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're going to take the negative. And put it on the a1. Again i'm going to take the jumper cableMoreYou're going to take the negative. And put it on the a1. Again i'm going to take the jumper cable from a2 to s1 you're going to take the positive cable from the jumper.
What are the symptoms of a bad solenoid in a golf cart?
On an electric golf cart, the most common symptom is the solenoid is not delivering electricity to the controller when the vehicle's ignition is turned on. In normal operating conditions, the solenoid clicks on and off with the ignition switch. A failing solenoid will generally not click.
Do all golf cart motors have a reset button?
Electric golf cart motors have a reset button on their chassis which is designed to put your motor back into its original factory state. While it doesn't repair damage that may have occurred to the motor over the years, obviously, it does help to overturn any changes to the operation which may have occurred.
Does a ezgo golf cart have a reset button?
Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button. Push the button to reset the motor.
Is there a fuse on an ezgo golf cart?
Most EZ-GO carts will the fuse located in the charging receptacle.
How do you diagnose a golf cart problem?
There are a few simple problems that you can fix yourself that will not necessitate professional maintenance.Test the wall socket where you charge your cart. ... Expose your golf cart batteries. ... Test the batteries for voltage. ... Replace dead batteries. ... Expose the motor for inspection. ... Reset the motor. ... Test the cart.
How do you fix a golf cart that won't move?
When the cart won't move, you have to be sure that the batteries are sending sufficient power to the circuit. You must check the fuse. Use the voltmeter to check the voltage at the key switch. In a cart with batteries rated at 48V, it must show 48V at the key switch.
Why won't My EZGO start?
Check to make sure the golf cart transmission selector is in the "park" position. Some models of E-Z-GO gas-powered carts may fail to start with a charge if the selector is not fully in the "park" position.
What is the controller on an EZGO golf cart?
Known as the heart of the EZGO golf cart, the controller’s core objective is to control the speed of the golf cart. It is a needed component in a AC and brushless DC motor. Without the controller, the golf cart will not work. The speed controller is not present in the DC motor vehicles, which is why they do not have varying speeds.
Where are the speed controllers on an EZGO cart?
Many times, the speed controllers of an EZGO cart are damaged or broken. These speed controllers are located under the EZGO cart seat. Check the speed controller’s attachment near the carburetor.
Why is my EZGO controller getting hot?
In general, if the EZGO controller is getting hotter, it’s due to steep rise and driving on higher roads. Then the reason will simply be that the load on the engine and motor is also causing the controller to get hot.
How to connect a voltmeter to a speed controller?
First, connect the voltmeter to the controller and the battery. Connect the voltmeter to the M terminal of the speed controller and the negative terminal of the cart battery.
What is the purpose of a golf cart controller?
Golf cart controllers play an important part in which its main job is to control the speed of a golf cart. However, many times, the controller tends to act up or simply stops working. This is when it is very important to troubleshoot the problem immediately. Known as the heart of the EZGO golf cart, the controller’s core objective is to control ...
Why is my cart not moving forward?
If the cart is not moving forward or the speed is not getting regulated or there is a problem in controlling the speed, then the chances are that the controller is being erratic. Then, it is very important to troubleshoot the problem as soon as possible.
How to turn on maintenance mode on a golf cart?
When the cart is to be serviced or the controller needs troubleshooting, the maintenance switch under the seat needs to be flipped. Flip the switch and turn the tow maintenance mode on.
What is the problem with the EZ Go golf cart?
If you are having trouble with your EZ-Go electric golf cart, there are two areas that may play a role in the problem: the battery and the motor. If you have checked the battery and found it to be charging properly and providing a full amount of power to the motor, then you know that the motor is the problem. There is an easy method to check the electric motor on any EZ-Go golf cart.
How to remove electric motor from golf cart?
Go to the back of the golf cart and find the panel that covers the electric motor. Four or six screws will hold the panel in place. Use the screwdriver to remove all the screws, turning them counterclockwise and putting them in a secure location after removal. Remove the panel so the electric motor is visible.
How to reset an electric motor?
Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button. Push the button to reset the motor. Put the panel in place and secure it with ...
Is the battery on an EZ Go golf cart charged?
Warnings. Be certain that the battery is not being charged before you begin working on any EZ-Go electric golf cart. Be certain that the battery is not being charged before you begin working on any EZ-Go electric golf cart.
Why won't my TXT golf cart charge?
A TXT golf cart may not charge because of loose or broken wires, a dirty charging port, a blown fuse, or problems with the auxiliary contact.
Why does my golf cart stop moving?
This Golf cart is very temperamental, and even things like over-tightening a stud can make it stop moving. Check the F/R switch stud for overtightening. If it is over-tightened, the contact will not connect with the switch. Adjust this, and your golf cart will start working.
Why does my carburetor smoke?
Excessive amounts of white smoke are a sign that you have a problem with your cooling system. It could also be a sign that you have water in your cart system, so make sure you take the time to clean the carburetor.
Why is my cart sluggish?
If your cart has a dirty carburetor, it may be sluggish during acceleration. You can prevent these issues by regularly cleaning the carburetor.
Why are my golf cart drum brakes stuck?
Drum brakes can get stuck due to rust and corrosion. To remove your E-Z-Go golf cart drum brakes, follow these steps.
What to do if your charger is defective?
If your charger is defective, replace it with a DPI charger.
When was the RXV golf cart made?
The company first made RXV golf carts in 2008. You can find their serial in the following spots.
Why does my EZGO golf cart slow down?
Some problems that you may face with your EZGO golf cart are that the cart creeps along or slows down after starting at a normal pace. These issues could be related to the speed sensor.
Where is the speed sensor on an EZGO golf cart?
The speed sensor on an EZGO TXT golf cart is located close to the motor. This sensor is present on the rear side of the motor on the driver’s side of the golf cart.
How to bypass speed sensor on EZGO?
The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller . By disconnecting the J5 pin on the speed controller, this will cause the golf cart to creep along as the controller will go into limp mode.
Why does my golf cart beep when it goes downhill?
If the golf cart beeps very fast and continuously when it goes downhill, it means that the sensor is communicating with the speed controller. This indicates a faulty controller and replacing it should help.
How to replace a speed sensor magnet?
A pair of pliers can make the replacement easy. Remove the clip holding the speed sensor magnet in place. Pull the magnet out gently using the pliers. Put the new magnet in the same place from where you took out the old one. Fasten the holding clip once again and ensure that it doesn’t slip out of place.
Why does my golf cart beep?
Set the speed controller into Diagnostics mode and count the number of beeps that the golf cart gives out, to help you with the diagnosis. The controller is likely to be experiencing high current or low voltage or entering high temperature cut-off mode because of an intermittent switch, wire, or connection that deactivates the solenoid. Getting a new speed controller fitted should help to resolve the problem.
How to remove a speed sensor?
Remove the snap ring or circlip with two clips that hold the speed sensor in place , using a pair of pliers.
What does it mean when a controller is not turning?
It should increase from a reading of 0 to the full voltage of the battery. If the motor is not turning, the problem may be in the directional switch or motor. If there is no voltage, the controller is bad and must be replaced.
How to check if a controller is bad?
Connect the negative probe to the controller's M terminal and positive probe to the B+ terminal. Press the accelerator and watch to see if the voltage increases. It should increase from a reading of 0 to the full voltage of the battery. If the motor is not turning, the problem may be in the directional switch or motor. If there is no voltage, the controller is bad and must be replaced.
How to reset a golf cart?
Use a screwdriver to locate and expose the motor. It may have a small red reset button near the main power supply. Press this button and reassemble your cart. Connect the golf cart to the charger unit and recharge the batteries. Attempt to operate the golf cart again.
What does a golf cart solenoid sound like?
The solenoid should make a clicking sound when you turn the key to start the golf cart. If the solenoid doesn’t work and the battery is full, replace it.
How to check if a cart battery is depleted?
Test each battery with a voltmeter to see if it is depleted. With some models, the cart draws a small amount of electricity even when it’s not running. Over several months, this can completely discharge the battery. Modern chargers must detect a minimum voltage to initiate the recharge sequence. Leaving the cart unplugged for a long time can cause the battery voltage to fall below this level.
Why does my motor not spin?
If the motor does not spin, it might be burnt-out. Motor burn-out can result from excessive resistance from weight, grade, or poor traction. Uninstall the motor and inspect it for damaged bearings, field coils, or worn brushes. These parts can be replaced with right tools and some patience.
Can you adjust the torque strapping on a cart?
Some carts allow you to adjust the torque strapping the batteries in place; keep this within the manufacturer’s specifications to prevent vibration. Vibrations during movement can cause internal damage to batteries.
Can you reset an electric golf cart?
The motor is the last in a series of components that could fail. After determining that the cart’s batteries and charger are working properly, you can reset the motor to see if it runs. You must replace the motor if it has burnt out.
