Turn the engine crank pulley by hand until the compression stroke is at top dead center. Insert a.004 feeler gauge (E) as shown between the tappet (D) and the valve stem. There should be a slight drag when you slide the gauge back and forth, and if the clearance is too high, you need to adjust it in.
Full Answer
How do you adjust the speed on an EZ GO golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
When did EZ Go Stop Making 2-cycle golf carts?
The E-Z-GO company officially stopped producing its 2-cycle golf carts in 1991, when the 4-cylinder carts were introduced. However, for a few years, these engines were produced in limited availability in some golf carts and utility vehicles.
What is the oil-to-gas ratio for an E-Z-GO 2-cycle golf cart?
What Is the Oil-to-Gas Ratio for an E-Z-GO 2-Cycle Golf Cart? The proper ratio of oil to gas for an E-Z-GO 2-cycle golf cart is 1 gallon of gas to 1 ounce of oil. This is defined numerically as the ratio 128:1.
How do I tune-up my E-Z-Go gasoline engine?
These are the easy steps to perform a basic tune-up on your E-Z-Go gasoline engine using a minimum of tools and an optional tune-up kit. As always, we begin with the three basics…Air, fuel, spark. Unsure of your year and model?
How do you adjust the carburetor on a EZ Go golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
How do I speed up my ezgo gas golf cart?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you adjust the speed limiter on a EZ Go golf cart?
0:495:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut.MoreIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut. The more you tighten the larger nut the faster your cart will.
Why does my 2 stroke golf cart backfire?
Engine backfiring occurs when there is an air leak within your golf cart or sometimes when there is too much fuel inside. This can cause the piston to slam against the cylinder head and cause a tapping sound. An essential component of any golf cart is the drive belt.
Why is my ezgo golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
How do I get more power from my gas golf cart?
How to Make Your Gas-Powdered Golf Cart Faster [Updated, 2022]1 Use A Better Golf Cart Battery.2 Increase Torque.3 Upgrade the Golf Cart Motor.4 Install a Torque Converter.5 Install a Higher-Performance Clutch.6 Tweak The Governor.7 Install A Cold Air Intake.8 Get Bigger Golf Cart Tires.More items...•
Where is the speed controller on an ezgo golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
How fast does an ezgo golf cart go?
And the fastest electric EZGO is the 2Five that goes 25 mph. And the fastest EZGO gasoline golf cart also only goes 19 mph.
How fast can a golf cart go without a governor?
A typical electric cart without an upgraded speed control tops out around 12 mph.
Why is my golf cart sputtering?
Golf carts can spit and sputter for several reasons, but mainly due to worn out spark plugs or dirty filters inside the fuel system. There might be something wrong with the fuel system of your cart. You could be having a spit and sputter problem because the filter, pump and injectors in your golf cart are very dirty.
Why does my golf cart backfire when I let off the gas?
The golf cart backfires when you let off gas is because the carburetor butterfly isn't getting closed completely. Air suction from the exhaust gasket is another possible cause. Checking the carburetor and adjusting the return spring to its original position so that the carburetor is closed solves the problem.
What causes golf cart hesitation?
In most cases, the hesitation problem occurs due to bad batteries. If you have bought new batteries for your EZGO RXV, make sure to fully charge them before the first use. Batteries should then be charged after every use. To keep the batteries in check, get a Digital MultiMeter to measure the individual voltage.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
Step 1: Air filter
The canister air filter is accessed by raising and lifting out the cart seat, locating the cylindrically shaped airbox with a cap on the end, and unsnapping the two holding clips on each side. Remove the lid and then the filter. Installing your new air filter is the reverse of these steps.
Step2: Spark Plugs
Despite the many years of EZGO carts, there are only two sparkplugs that EZGO carts use, BPR4ES and BPR2ES; the latter for Kawasaki engined EZGO carts.
Step 3: Fuel
The fuel filter is located in line between the fuel tank and the fuel pump. If the housing is clear plastic, make sure that the fuel inside is not dark amber or discolored from age.
Conclusion
All of these adjustments can be made on your EzGo Golf Cart without spending more than your time and a tune up kit.
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does an EFI carb require more maintenance than an EFI?
The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
Where is the main jet on a 2 cycle engine?
The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
For the 295cc or a 350cc twin-cylinder OHC engine. 1991 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 10mm socket wrench, flat blade screwdriver, and a feeler gauge. Note: if the screw (C) has a square head instead of a flat blade slot, this takes a tool designed just for this purpose.
For the Kawasaki FJ400 401cc 4-cycle Single Cylinder 1996 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 3mm hex wrench, feeler gauge.
How to tell if a golf cart is a 2-cycle or 4-cycle?
One of the easiest ways to determine if an engine is a 2- or 4-cycle is by the number of spark plugs. One spark plug defines a 2-cycle engine, while a 4-cycle engine has four spark plugs. When reassembling one of these 2-cycle ...
How many spark plugs are needed for a 2 cycle engine?
One spark plug defines a 2-cycle engine, while a 4-cycle engine has four spark plugs. When reassembling one of these 2-cycle engines, the most important thing to keep in mind is to not overbore the cylinders to a larger diameter. After compressing the springs into the cylinder, one cannot rotate the cylinder.
