- Loosen the nut attached to the governor arm with a 7/16” wrench to turn the shaft.
- Push the governor arm to the back of the cart and grasp it with your hand.
- Turn the governor shaft in the counter-clockwise direction until it cannot be turned further.
- Retighten the nut and let go off your hold on the governor arm.
- This method also helps to slow down the cart.
How do you remove the governor on a riding lawn mower?
Method 2 Loosen the nut attached to the governor arm with a 7/16” wrench to turn the shaft. Push the governor arm to the back of the cart and grasp it with your hand. Turn the governor shaft in the counter-clockwise direction until it cannot be turned further. Retighten the nut and let …
How do you fix a hole in a governor on a golf cart?
Jan 07, 2022 · Remove the screws that hold the governor’s cover in place. There are three screws in total – two Phillips head screws and one flathead screw. Use the wire cutters to cut the zip tie that holds the wires to the governor. Remove the screws that hold the governor to the battery pack. You Can Now Put a New Governor on or Remove One from Your ...
How fast can a golf cart go without a governor?
Disconnect the gas pedal cable from the governor and reroute it to the carburetor. You've now eliminated the governor but you still need to adjust the gas pedal for optimum power. Using your wrench, remove the bolt on the gas pedal shaft. Slide the shaft up so there is more play in the gas pedal. Tighten the bolt and then start the cart.
Can you remove the governor on an electric golf cart?
Feb 05, 2020 · To disable the governor, you need to stop this piece from moving. Place a small rubber band on top of the T at the thickest part where the governor moves. Look behind the governor to find a small metal rod that's permanently attached to the club car and stretch your rubber band enough to connect it to that metal rod. Click to see full answer.
How Does a Golf Cart Governor Work
Governors play an important role in electric golf carts by limiting the speed they can travel. This is an important safety feature, as it prevents the cart from going too fast and helps ensure passengers’ safety.
How to Take the Governor off a Golf Cart
Removing the governor from a golf cart is a simple process that can be done with common tools. Here’s what you’ll need:
Frequently Asked Questions about Golf Cart Speed Governors
If you’re looking for ways to speed up your golf cart, there are a few things you can do. Start by removing the governor on top of the engine if you haven’t already. If it doesn’t have a governor, then you’ll need to open up the cart and look at the gear shaft to see if it’s turning.
How to remove governor from golf cart?
How to Remove the Governor From a Golf Cart. You hit the links. The course is open in front of you as far as the eye can see. The only thing holding you back is the put-put-puttering of your golf cart. Golf carts are governed to go anywhere from 12 to 14 miles per hour. But if you've got a few minutes, some simple mechanical know-how and a wrench, ...
Where is the governor on a car?
The governor generally sits on top of the engine . This is the easiest way to find the carburetor. Once you've followed the cable up to the governor, disconnect it there as well. You can save this cable for later use or throw it away.
How fast can a golf cart go?
Golf carts are governed to go anywhere from 12 to 14 miles per hour. But if you've got a few minutes, some simple mechanical know-how and a wrench, you can double the speed of your cart and zip through your round.
How to adjust a gas pedal on a cart?
Using your wrench, remove the bolt on the gas pedal shaft. Slide the shaft up so there is more play in the gas pedal. Tighten the bolt and then start the cart. You may need to adjust the gas pedal shaft a couple of times before you have it to your liking.
How to make a cart faster?
Step 1. The first option to making your cart faster is to replace the electronic speed control. This will enable more voltage to pass to the motor, producing the desired result. Unfortunately, this upgrade is not inexpensive as the unit can run anywhere from $100 to $1,000. Step 2.
How fast can a factory cart go?
The factory gear most likely has a 12.5:1 ratio, which allows the cart to achieve somewhere around 14 mph. If you swap out the factory gear for one with an 8:1 gear ratio, you'll up your top end to about 20 mph.
Can you drive a golf cart faster?
It should be noted that the golf cart you are trying to make faster may not be designed to do so. Weigh the options carefully and exercise caution whenever driving a golf cart at any speed. Remember that golf carts are not equipped with seat belts, air bags and other safety equipment that you find in automobiles.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to find the governor on a golf cart?
Locate the golf cart’s governor; you can find the governor by tracing the thickest cable running from the gas pedal. This cable runs through the governor on its way to the carburetor. Use a screwdriver—or in some cases a wrench—to loosen the tension on the governor’s springs. You have now adjusted the governor for faster speed.
Who is the writer of GolfCarCatalog.com?
GolfCarCatalog.com – “Adjusting Your Golf Cart’s Governor”. Writer Bio. Richard Kalinowski began writing professionally in 2006. He also works as a website programmer and graphic designer for several clients.
Can a golf cart be a nuisance?
In practice, golf carts can be more of a nuisance than a help, as many standard carts creep along at unbearably slow speeds. Luckily, you don’t have to stick with these standard speeds. Golf cart speed is often controlled by a device called a governor, and you can adjust the governor on a golf cart relatively easily to make the cart faster.
Can golf carts be adjusted manually?
By Richard Kalinowski. Governors limit the speed of golf carts but can be adjusted manually. In theory, golf carts make it easier for players to get across the course, saving their much-needed energy for the game. In practice, golf carts can be more of a nuisance than a help, as many standard carts creep along at unbearably slow speeds.