How do you take the governor off a EZ Go golf cart? If you find this rod, then your governor can be easily adjusted by accessing the cart’s inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart’s governance to increase the overall speed.
How do you adjust the governor on an EZ GO golf cart?
The function of the governor to control speed within factory preset limits may be affected by adjusting the governor spring. E-Z-Go does not recommend additional measures to alter the governor to permit speeds outside factory preset limits. Locate the governor arm mounted on top of the rear axle case underneath the cart.
How do you remove the governor on a golf cart?
1 Loosen the nut attached to the governor arm with a 7/16” wrench to turn the shaft. 2 Push the governor arm to the back of the cart and grasp it with your hand. 3 Turn the governor shaft in the counter-clockwise direction until it cannot be turned further. 4 Retighten the nut and let go off your hold on the governor arm. More items...
How does a governor control the speed of a golf cart?
The speed of a Golf cart is often controlled by a device called the governor, and you can adjust it for higher speed easily on your own. You can take your cart to new heights with this handy device. The governor regulates how fast you go, and it's easy enough that even a novice mechanic could change speeds in no time at all!
Do EZ GO spark plugs have governors?
Many manufacturers, including EZ Go, do not want consumers tampering with their engines, and have thus hidden the governors in the spark plug ignition. This is very difficult to adjust without ruining the engine, and should be left to trained professionals.
How do you take the governor off a EZ Go golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How do you turn off the governor on a electric golf cart?
0:101:28Golf Tips & Etiquette : Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment.MoreWell a golf cart's governor located is actually down in the motor. Compartment.
How do I make my ezgo golf cart go faster?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you adjust the speed limiter on a EZ Go golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
Where is the speed controller on an ezgo golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
Why is my ezgo golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
How do I unlock Freedom mode on ezgo?
Toggle the forward/reverse switch from the "neutral" position to "reverse" five times in quick succession. After a few seconds, the computer controller will beep four times, indicating it has shifted into the freedom mode. Flip the run-tow switch back to “tow” and then "run” to escape the diagnostic setting mode.
How do you bypass the speed sensor on a EZ Go golf cart?
The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller. By disconnecting the J5 pin on the speed controller, this will cause the golf cart to creep along as the controller will go into limp mode.
How fast does an ezgo golf cart go?
And the fastest electric EZGO is the 2Five that goes 25 mph. And the fastest EZGO gasoline golf cart also only goes 19 mph.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
How can I make my gas golf cart go faster?
Increase the RPM An increase in the input shaft rpm for all differential ratios will produce a higher speed. For a gas golf cart, other than adjusting the governor, the speed may be enhanced by replacing the engine with a higher rpm output model.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to remove the black plastic cover on a golf cart?
Remove the screws from the black plastic cover at the rear of the seat. There should be five screws in most models. The engine is in the front of golf carts , underneath this panel. Take off the plastic cover and set it aside with the seats.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How to tell if a gas pedal is a governor?
Follow the thickest cable coming from the gas pedal until your find a small spring wrapped around a metal rod. This is the governor. The spring apparatus will have two nuts, one small nut and one larger nut, holding it onto the rod.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How Does a Golf Cart Governor Work
Governors play an important role in electric golf carts by limiting the speed they can travel. This is an important safety feature, as it prevents the cart from going too fast and helps ensure passengers’ safety.
How to Take the Governor off a Golf Cart
Removing the governor from a golf cart is a simple process that can be done with common tools. Here’s what you’ll need:
Frequently Asked Questions about Golf Cart Speed Governors
If you’re looking for ways to speed up your golf cart, there are a few things you can do. Start by removing the governor on top of the engine if you haven’t already. If it doesn’t have a governor, then you’ll need to open up the cart and look at the gear shaft to see if it’s turning.
How to adjust a governor spring?
Loosen the adjusting locknut on the end of the governor spring. Rotate the locknut to expand or compress the spring until its length is 2 1/2 inches.
How to increase maximum governed speed?
Check manufacturer's specifications for the maximum governed speed and adjust the governor spring locknut if necessary. Tightening the spring locknut increases maximum governed speed, while loosening the locknut decreases maximum governed speed.
