- Determine the hole position. This is done by pacing the distances as set from the pin sheet. Say the pin placement is...
- Now that the hole position is determined, if you are using a twist in or rotating cup hole cutter, hold the cup hole...
- Release the grass plug into the container, wipe off the outside of the cutting cylinder with a towel, carefully...
Full Answer
How to maintain the Cup hole cutter?
A simple step in quality cup hole cutting is to keep the cup hole cutter sharp. For daily cup hole cutting, the following procedures are recommended. 1. The cup hole cutter is sharpened weekly. 2. The cup hole cutter is carried in the cab of the transport vehicle, preferably with a rubber mat to protect the cutting edge.
How do you use a cup setter on a golf course?
Insert the cup setter into the cup. Then, push down firmly until the rim of the cup setter contacts the surface of the green. It is important not to force the cup setter. If you do not achieve full depth with firm foot pressure, the hole was not cut to the proper depth.
How do I know when the Cup cutter has reached 7 inches?
There are various devices used to indicate when the cup cutter has reached the 7-inch depth when the cup hole is cut using the two plug method. What works well is measuring from the top of the scallops on the cutting cylinder 7 inches, mark the spots, and either use paint or a high visibility tape in the area above your marks.
How do you remove soil from a cup cutter?
If the soil does fall out, carefully replace the cup cutter back into the hole, and once the cup cutter is completely in the hole, lift up one to two inches on the handle and push down gently to retrieve the soil that has fallen out. Again, slowly remove the cup cutter with the left /right rotation.
How do you use a cup cutter?
4:3715:57Basics of Cup Cutting - YouTubeYouTubeStart of suggested clipEnd of suggested clipInsert the cup cutter vertically into the putting surface to the full depth insert. The cup cutterMoreInsert the cup cutter vertically into the putting surface to the full depth insert. The cup cutter as smoothly as possible to avoid damaging the plug. And keep the cutter as straight as possible.
How does a golf hole cutter work?
How It Works: A hole cutter precisely places pin positions and deftly replaces plugsThe placement. The pin location is far from random. ... The cut. The wooden nozzle pushes the sharp cylinder through the grass, pristinely pulling the spherical mass from the ground. ... The extraction. ... The replacement.
How do you change cups on a golf course?
The actual way this is done varies from club to club, but the basics are still the same. Place the cup cutter straight over the desired area and with your feet shoulder width apart slowly apply pressure while mowing the cup cutter to the left, then to the right. Repeat. Go down only 2-3" and remove the cutter.
How do you change the cups on a golf green?
1:566:05How to change a cup on a golf course green - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn order to do that you first take out the flagstick. Set it off to the side you won't need thatMoreIn order to do that you first take out the flagstick. Set it off to the side you won't need that until the very end when you go to replace it. Then we use our cup removal tool our cup.
How deep should the Cup be in a golf hole?
between 4”-6”The Golf Cup is designed with a center hole for holding the flagstick which indicates where the hole is from far away. Golf Hole (Golf Cups) have a regulated diameter of 4.25” (108 mm) and total depth between 4”-6” (101.6-152.4 mm).
How deep should a golf hole be cut?
The Rules of Golf explicitly state that a hole must be 4.25 inches in diameter and at least 4 inches in depth.
How do you install golf cups?
Guide to Installing Golf Cups for the Best Putting GreensPrepare the Ground for Installation. ... Install the Putting Green Base. ... Decide Where to Place the Golf Cups. ... Make the Holes for the Golf Cups. ... Insert the Cups. ... Apply Concrete Around the Cup and Level It. ... Finalize the Base. ... Lay the Putting Green Turf over the Base.More items...•
How do you cut the green on a golf course?
0:000:51Cutting a Golf Green Part 1 of 2 - LandscapeSafety.com - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhile mowing it is not appropriate to slow the machine. You must keep a constant ground speed whenMoreWhile mowing it is not appropriate to slow the machine. You must keep a constant ground speed when the reels are touching the putting surface.
Why do golfers poke the green?
Aerating when grass is healthy and actively growing minimizes damage and allows for a quick return to optimal playing conditions. Aerating at other times may be more convenient for the golf schedule, but it lengthens recovery times, increases the risk of an invasion of weeds and could cause lasting damage.
How do you cut a green hole?
0:487:17Installing Putting Green Cups - Backyard Artificial Grass ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the sand is wet. It's not going to come out of the green very well and when you're trying to cut.MoreIf the sand is wet. It's not going to come out of the green very well and when you're trying to cut. This especially the shot-maker product which is almost an inch tall.
How do you set a putting green cup?
0:054:26putting green cup installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipPretty level by using a torpedo level it doesn't it's not real important right now depending on whatMorePretty level by using a torpedo level it doesn't it's not real important right now depending on what height your turf is is how high you'll set your cups and your cups will be adjustable.
How do you dig holes in golf?
0:182:19Fore The Golfer: Changing A Hole Location - YouTubeYouTubeStart of suggested clipEnd of suggested clipAs possible. The hole cutter tool removes. The plug and stores it within the sleeve of the device.MoreAs possible. The hole cutter tool removes. The plug and stores it within the sleeve of the device. The hole liner is then removed from the present hole location. And inserted into the new hole.
How to keep cup hole cutter sharp?
1. The cup hole cutter is sharpened weekly. 2. The cup hole cutter is carried in the cab of the transport vehicle, preferably with a rubber mat to protect the cu tting edge. 3.
How far above the green is a cup hole cutter?
2. Now that the hole position is determined, if you are using a twist in or rotating cup hole cutter, hold the cup hole cutter 18 to 24 inches above the green and release it.
How to remove soil plug from cutting cylinder?
Clean the cutting cylinder before you insert it into the hole. Place the cylinder into the hole, making sure it is all the way to the bottom of the hole. Release the soil plug while keeping the cylinder contacting the bottom of the hole. Once the soil plug is released, remove the cylinder from the hole.
How to get soil out of a cup cutter?
If the soil does fall out, carefully replace the cup cutter back into the hole, and once the cup cutter is completely in the hole, lift up one to two inches on the handle and push down gently to retrieve the soil that has fallen out . Again, slowly remove the cup cutter with the left /right rotation.
What is the most valuable area of a golf course?
Greens are the most valuable area of any golf course so daily cup hole cutting is an important task. The most valuable areas of a golf course are the greens . Any activity that occurs on the greens should be the most meticulous, cautious and professional activity that transpires any where on the golf course.
